MadgeTech MadgeNet RFRHTemp2000A Specification sheet

RFRHTemp2000A
RFRHTemp2000A
Wireless Temperature and Humidity Data Logger
Product User Guide

Product User Guide
RFRHTemp2000A Data Logger
Quick Start Steps ........................................... 1
Product Overview .......................................... 2
Additional Features & Operation .................... 3
Mounting Instructions ................................... 4
Product Maintenance ..................................... 5
Recalibration .................................................. 5
RMA Instructions ............................................. 5
General Specifications.................................. 6-7
RFC1000 Transceiver
Product Overview .......................................... 9
Installation Guide ........................................... 9
Mounting Instruction ................................... 10
Channel Programming ................................. 11
Deployment & Activation .............................. 12
General Specifications................................... 12
Compliance Information................................ 13
Troubleshooting Tips ............ Back Cover
Table of Contents

1
1. Install the MadgeTech 4 Software and USB Drivers onto a Windows PC.
2. The RFC1000 interface device comes with a USB cable. Plug one end of the cable into
an available USB port on the PC and plug the opposite end of the cable into the
communication port on the RFC1000.
3. Push and hold the wireless button on the RFRHTemp2000A for 5 seconds to activate
wireless communication. The display will confirm “Wireless: ON” and the blue LED will
blink every 15 seconds.
4. Launch the MadgeTech 4 Software. All active MadgeTech Data Loggers that are within
range will automatically appear in the connected devices window. Each data logger in
the list can be identified by serial number (printed on the exterior of the logger).
5. To claim a device, select the desired data logger in the list and click the Claim icon.
6. Select the start method, reading rate and any other parameters appropriate for the
desired data logging application. Once configured, deploy the data logger by clicking
the Start icon.
7. To download data, select the device in the list, click the Stop icon, and then click the
Download icon. A graph will automatically display the data.
Quick Start Steps
1. Install the MadgeTech 4 Software and USB Drivers onto a Windows PC.
2. Before plugging the data logger in the computer, make sure the wireless setting on
the device is set to “Wireless: OFF”. If wireless mode is on, press and hold the Wireless
button on the device for 5 seconds.
3. The RFRHTemp2000A comes with a USB cable. Plug one end of the cable into an
available USB port on the PC and plug the opposite end of the cable into the
communication port on the RFRHTemp2000A.
4. Launch the MadgeTech 4 Software. The RFRHTemp2000A will appear in the connected
devices window indicating the device has been recognized.
5. Select the start method, reading rate and any other parameters appropriate for the
desired data logging application. Once configured, deploy the data logger by clicking
the Start icon.
6. To download data, select the device in the list, click the Stop icon, and then click the
Download icon. A graph will automatically display the data.
Product Operation (Plugged In)
Product Operation (Wireless)

Product User Guide
Product Overview
The RFRHTemp2000A is two-way Wireless temperature and humidity data logger with LCD.
Transmits up to 2000 ft maximum (outdoors unobstructed). Built-in memory also stores
data internally. This device is calibrated traceable to NIST and is available with a Calibration
Certificate. The RFRHTemp2000A is ideal for both industrial or laboratory applications
including supply chain storage facilities, incubator monitoring and HVAC studies. Designed
with external humidity and RTD based temperature sensors, the device provides a fast
response time for both parameters. The RFRHTemp2000A is a wireless temperature and
humidity data logging and alarming system with LCD display. A base is included with the
data logger for mounting purposes.
Selection Buttons
The logger is designed with 3 direct selection buttons: Scroll, Units and Wireless.
•Scroll: Allows user to scroll through current readings, average stats and device status
information displayed on the LCD Screen.
•Units: Allows user to change displayed units of measurement to either °F or °C.
•Wireless: Push and hold this button for 5 seconds to activate or deactivate wireless
communication.
•Manual Reset Option: Allows user to manually reset the statistics within the device to 0
without needing to use the MadgeTech software. Any data recorded up to that point is
recorded and saved. To apply the manual reset, press and hold the scroll key down for
three seconds.
LED Indicators
•Status: Green LED blinks every 5 seconds to indicate unit is logging.
•Wireless: Blue LED blinks every 15 seconds to indicate unit is operating in wireless mode.
•Alarm: Red LED blinks every 1 second to indicate an alarm condition.
2

RFRHTemp2000A
Additional Features and Operation
Alarm Settings/Rules
In MadgeTech 4, alarms can be created
on two levels; in the software itself, and
programmed specifically to the data logger.
Creating alarm rules in the software allows
the user to utilize alarms while real time
recording, and have the added benefit of
features such as e-mail and SMS notification.
An alarm that is programmed on the data
logger will only alert the user from the
device itself, whether that is by a flashing
LED, audible alarm, or local LCD notification.
Creating a Real time Alarm Rule
1. Within the Device tab in MadgeTech 4, in the Alarms group, click Manage Rules,
then select New.
2. Enter a name in the Rule name box, and select whether notifications will occur when
All conditions are met or Any condition is met.
3. Select the desired conditions to have met before notifications occur, and select which
notifications will occur from the drop down menus.
4. If selecting to receive notifications by email or text message, click Email settings and
make sure the correct info has been entered. Email and text message notifications will
not be received if settings are incorrect.
5. Click OK. The OK button will be disabled if the Rule name box is empty.
Changing the Alarm Settings of a Device
1. In the Connected devices panel, select the RFRHTemp2000A device.
2. Click the Properties button under the device tab at the top of the software, and select
the Alarm tab in the Properties window.
3. The High and Low settings indicate reading thresholds at which the alarm becomes active.
4. The Delay setting indicates how long to wait before the alarm becomes active after
passing an alarm threshold.
5. The Use cumulative alarm delay checkbox indicates whether the alarm delay should
reset when reading values fall back within the alarm threshold.
6. Once the alarm is configured appropriately, click Apply to save the settings.
**Please refer to the Help file in the MadgeTech software for more information regarding alarm settings**
3

Product User Guide
The base provided with the RFRHTemp2000A can be used in two ways.
• The bottom of the logger snaps in place to use and mount the unit on a table top or
horizontal surface.
• The base can also securely snap to the backside of the logger for wall mounting if desired
(as shown below).
• There are two holes in the base to allow for screws for mounting.
Mounting Instructions
4
Still need help? For more troubleshooting tips and information, refer to the built in help
section of the MadgeTech 4 software, visit our Knowledge Base online at
www.madgetech.com/kbase or contact us for customer support at 603-456-2011.

RFRHTemp2000A
Product Maintenance
Battery Replacement
Materials: U9VL-J Battery
1. On the bottom of the enclosure, open the battery compartment by pulling in on the
cover tab.
2. Remove the battery by pulling it from the compartment.
3. Install the new battery, taking note of the polarity.
4. Push the cover closed until it clicks.
Recalibration
Standard recalibration for the RFRHTemp2000A is one point at 25 °C for the internal
temperature channel, and two points at 25 %RH and 75 %RH for the humidity channel.
Recalibration is recommended annually for any MadgeTech data logger; a reminder is
automatically displayed in the software when the device is due.
Countries approved for use, purchase and distribution of the RFRHTemp2000A:
Australia, Austria, Belgium, Bulgaria, Canada, Chile, China, Columbia, Croatia, Cyprus, Czech Republic, Denmark,
Ecuador, Estonia, Finland, France, Germany, Greece, Honduras, Hungary, Iceland, Ireland, Israel, Japan, Latvia,
Liechtenstein, Lithuania, Luxembourg, Malaysia, Malta, Mexico, New Zealand, Norway, Peru, Poland, Portugal,
Romania, Saudi Arabia, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sweden, Switzerland,
Thailand, The Netherlands, Turkey, United Kingdom, United States, Venezuela, Vietnam
5

Product User Guide
Reading Rate 1 reading every second up to 1 reading every 24 hours
Memory 16,128 readings
LED Functionality
• Green LED blinks every 5 seconds to indicate unit is logging
• Blue LED blinks every 15 seconds to indicate unit is in wireless mode
• Red LED blinks every 1 second to indicate alarm condition
Memory Wrap
Around Yes
Start Modes Immediate Start
Calibration Digital calibration through software
Calibration Date Automatically recorded within device
Battery Type Ultralife 9V lithium battery included; user replaceable
Battery Life 3 years typical at 1 minute reading rate
Data Format
• For Display: °C or °F, %RH
• For Software: Date and time stamped °C, K, °F, or °R ,%RH, mg/mL,
Dew Point - °C/K/°F/°R
Time Accuracy ±1 minute/month
Computer Interface USB to mini USB, 250,000 baud for standalone operation or RFC1000
required for wireless operation
Software XP SP3/Vista/Windows 7/Windows 8 (MadgeTech 4 only)
Operating
Environment -20 °C to +60 °C (-4 °F to +140 °F); 0 %RH to 95 %RH non-condensing
Dimensions 3.0 in x 3.5 in x 0.95 in
(76.2 mm x 88.9 mm x 24.1 mm) - Data logger only
Weight 4.1 oz (0.2563 lbs)
Enclosure Material ABS Plastic
Alarm
User configurable audible, on-screen, email and text (SMS) alarms.
Alarm Delay: A cumulative alarm delay may be set in which the device
will activate the alarm (via LED) only when the device has recorded a
user specified time duration of data.
Audible Alarm
Functionality 1 Beep per second for reading alarm above/below threshold
Approvals US (FCC), CA (IC), CE, South Korea (KCC), China (CMIIT), Japan (LCIE)
RFRHTemp2000A General Specifications
6
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or
more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation
at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.

RFRHTemp2000A
Internal Channel
Temperature Range -20 °C to +60 °C (-4 °F to +140 °F)
Temperature Resolution 0.01 °C (0.02 °F)
Calibrated Accuracy ±0.5 °C/± 0.9 °F (0 °C to +55 °C/32 °F to 131 °F )
Response Time 10 minutes free air
Temperature
Humidity Range 0 %RH to 95 %RH
Humidity Resolution 0.1 %RH
Humidity Calibrated
Accuracy
±3.0 %RH, ±2.0 %RH typical @ 25 °C
(10 %RH to 90 %RH; 5 °C to 55 °C)
Response Time 2 minutes to 63% of change
Humidity
RF Frequency 2.45 GHz IEEE 802.15.4 ultra-low power wireless transceiver
with fully bi-directional communication
Band ISM band 2.405-2.475 GHz
Operation (channels 11 through 25) @ 250 kbps
Maximum Output
Power +0 dBm typical
Receiver Sensitivity
(RFC1000) -95 dBm typical
Transmission Distance
(to other RFC1000’s)
• RFC1000
4,000 ft max. outdoors - line of sight unobstructed
1,000 ft max. indoors - typical urban environment
• RFC1000-CE
2,500 ft max. outdoors - line of sight unobstructed
700 ft max. indoors - typical urban environment
• RFC1000-IP69K
4,000 ft max. outdoors - line of sight unobstructed
1,000 ft max. indoors - typical urban environment
Transmission Distance
(to data loggers)
• RFC1000, RFC1000-CE & RFC1000-IP69K
2,000 ft max. outdoors - line of sight unobstructed
500 ft max. indoors - typical urban environment
Wireless
7
Battery Warning
WARNING: BATTERY MAY LEAK, FLAME OR EXPLODE IF DISASSEMBLED, SHORTED, CHARGED, CONNECTED TOGETHER,
MIXED WITH USED OR OTHER BATTERIES, AND/OR EXPOSED TO FIRE/HIGH TEMPERATURE. DISCARD USED BATTERY
PROMPTLY, KEEP OUT OF REACH OF CHILDREN.
Specifications subject to change.
See MadgeTech’s terms and conditions at www.madgetech.com

Product User Guide
RFC1000
Wireless Transceiver
8
Other models available:
RFC1000-CE - Approved for
European markets
RFC1000-IP69K - Splash Proof
for harsh environments

RFC1000
Product Overview
MadgeTech has designed the RFC1000, a high powered transceiver that has a substantially
long transmission range, providing enhanced performance in occluded environments
(ovens, refrigerators, etc.). The RFC1000 also features an external antenna, allowing more
flexibility with mounting positions in both orientation and proximity to metal walls. The
device may be used as a repeater, or directly plugged into the Windows PC.
Transmission Distance
The RFC1000 transmits to other RFC1000s up to 4000 feet maximum typical outdoors/
line of sight, 1000 feet maximum typical indoors/urban. The RFC1000 transmits to data
loggers up to 2000 feet maximum typical outdoors/line of sight, 500 feet maximum typical
indoors/urban. The RFC1000 can connect to a maximum of 64 data loggers. The RFC1000
transmits on a frequency of 2.405 GHz - 2.475 GHz.
Operating Environment
The RFC1000 is rated for use in an environment with temperatures from -20 °C to 85 °C
and a humidity range of 0 %RH to 95 %RH non-condensing. The RFC1000 is rated IP40
and is protected against solids that are greater than 1mm in size. This device is not water
resistant.
LEDs
The red LED indicates that the device has power. The green LED will blink when
communicating with other MadgeTech devices.
9
Installation Guide
1. Locate the Autorun.exe file on the MadgeTech 4 Software Flash Drive.
2. Select “MadgeTech Software” in the MadgeTech Installer Options window panel.
3. If the Windows PC doesn’t already have .NET 4.0 Framework, installation may be
required. Note: To see if the .NET 4.0 Framework is installed, go to the Windows Control
Panel and select Programs. “Microsoft .NET Framework 4.0” would be listed as a Windows
program.
Select “Install MadgeTech Software” if .NET framework is installed on the Windows PC,
or if installing on a Windows 8 machine.
Installing the MadgeTech 4 Software
Insert the MadgeTech 4 Software Flash Drive into an open USB
port on a Windows PC. If the autorun does not appear, locate the
drive on the computer and double click on Autorun.exe. Follow
the instructions provided in the Installation Wizard.

Product User Guide
Mounting Instructions
For best wireless performance, both the RFC1000 and the MadgeTech data loggers should
be mounted in the same orientation. This usually means that the external antenna should
be pointing straight up. The antenna can pivot to accommodate either a wall mount or a
desk mount.
10

RFC1000
Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 Channel 16
Channel 17 Channel 18 Channel 19 Channel 20 Channel 21 Channel 22
Channel 23 Channel 24 Channel 25 Channel 26
(not supported)
Channel Programming
The RFC1000 transmits data on the 2.4 GHz band and is programmed by default on
channel 11. Each MadgeTech Wireless Data Logger and RFC1000 has a set of dip switches
with which the channel may be programmed.
Different wireless channels may be used to create multiple networks in one area, or to avoid
wireless interference from other devices. Any MadgeTech data logger or RFC1000 that is on
the same network is required to use the same channel. If all of the devices are not on the
same channel, the devices will not communicate with one another.
The images below show the orientations available of the switches for each channel. Channel 26
(all switches in the up position) is not supported.
11
Follow the instructions below to configure the channel settings of the RFC1000
1. To program the channel on an RFC1000, first unplug the RFC1000.
2. Use a Phillips head screwdriver to unscrew the enclosure.
3. Find the dip switches located on the front of the PCB circuit board.
4. Change the dip switches to match the desired channel using the diagram above.
5. Screw the enclosure back together and reconnect the RFC1000.
Close-up

Product User Guide
RFRHTemp2000A: To program the channel on the RFRHTemp2000A data logger, start by switching
the wireless mode to OFF by holding down the Wireless button on the data logger for 5 seconds.
Step 1: Use the USB Cable, plug the USB end of the cable into an available USB port on the PC.
Step 2: Plug the opposite end of the cable into the communication port on the RFRHTemp2000A.
Step 3: Open the MadgeTech Software. Locate and select the RFRHTemp2000A in the Connected
Devices panel.
Step 4: In the Device tab, click the Properties icon. The Properties screen will display information
about the device including Wireless setting.
Step 5: Under the Wireless tab, select a desired channel (11-25) that will match with the RFC1000.
Save all changes, disconnect the data logger, and return the device to wireless mode by
holding down the Wireless button for 5 seconds.
Deploying and Activating Devices
Step 1: Plug the RFC1000 into the USB port on the base station computer. (Additional RFC1000s
can be used as repeaters to transmit over greater distances)
Step 2: If using multiple RFC1000s plug each one into a wall outlet in the desired locations.
(If transmitting over a distance greater than 1000 feet indoors or 4000 feet outdoors or there
are walls/obstacles/corners that need to be maneuvered around, set up additional RFC1000s
as needed.)
Step 3: Verify that the data loggers are in wireless transmission mode. (See Channel Programming
steps above)
Step 4: On a Windows PC, launch the Madgetech 4 software program. All active data loggers will
be listed in the software showing that the device(s) are recognized.
Step 5: To activate the data loggers, click on one to highlight, then click the Claim icon, and then
click the Start button. Do this for each logger in the list that needs to be activated.
RFC1000 General Specifications
12
Interface Type USB (to PC) / Wireless (to Data Logger)
Operating Environment -20 °C to +85 °C, 0 %RH to 95 %RH non-condensing
LED Indicators Red & Green
Enclosure Materials ABS Plastic (body), PVC Plastic (antenna)
Dimensions Enclosure: 3.8 in x 1.6 in x 0.8 in / Antenna: 7.2 in
Approvals FCC ID: OA3MRF24J40MC, IC#: 7693A-24J40MC
Transmission Distance
(To other RFC1000’s)
• RFC1000 & RFC1000-IP69K
4,000 ft max. outdoors - line of sight unobstructed
1,000 ft max. indoors - typical urban environment
• RFC1000-CE
2,500 ft max. outdoors - line of sight unobstructed
700 ft max. indoors - typical urban environment
Transmission Distance
(To data loggers)
• RFC1000, RFC1000-CE & RFC1000-IP69K
2,000 ft max. outdoors - line of sight unobstructed
500 ft max. indoors - typical urban environment
Maximum number of
connected data loggers 64
Frequency 2.405 GHz - 2.475 GHz
Ingress Protection IP40

RFC1000
• “This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.”
• “To satisfy FCC RF Exposure requirements for mobile and base station transmission devices,
a separation distance of 20cm or more should be maintained between the antenna of
this device and persons during operation. To ensure compliance, operation at closer than
this distance is not recommended. The antenna(s) used for this transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.”
• “This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.”
• “Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé
pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain
de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire à l’établissement d’une communication satisfaisante.”
Compliance Information
13

Troubleshooting Tips
Why is the wireless data logger not appearing in the software?
If the RFRHTemp2000A doesn’t appear in the Connected Devices panel, or an error message is
received while using the RFRHTemp2000A, try the following:
• Check that the RFC1000 is properly connected. For more information, see Troubleshooting Interface
Cable problems (below).
• Ensure that the battery is not discharged. For best voltage accuracy, use a voltage meter connected to
the battery of the device. If possible, try switching the battery with a new 9V lithium.
• Ensure that no other MadgeTech software (such as MadgeTech 2, or MadgeNET) is running in the
background.
• Ensure that MadgeTech 4 is being used. MadgeTech 2 and MadgeNET are not the correct software for
connecting with the RFRHTemp2000A.
• Ensure that the Connected Devices panel is large enough to display devices. This can be verified by
positioning the cursor on the edge of the Connected Devices panel until the resize cursor appears, then
dragging the edge of the panel to resize it. The screen layout may also be reset in the options menu by
selecting File, Options, and scrolling to the bottom.
Troubleshooting Interface Cable problems
Check that the software properly recognizes the connected RFC1000 wireless transceiver.
If the wireless data logger is not appearing in the Connected Devices list, it may be that the RFC1000 is
not properly connected.
1. In the software, click the File button, then click Options.
2. In the Options window, click Communications.
3. The Detected Interfaces box will list all of the available communication interfaces. If the RFC1000 is
listed here, then the software has correctly recognized and is ready to use it.
Check that Windows recognizes the connected RFC1000 wireless transceiver.
If the software does not recognize the RFC1000, there may be a problem with Windows or the USB drivers.
1. In Windows, click Start, right-click Computer and choose Properties or press Windows+Break as a
keyboard shortcut.
2. Click Device Manager in the left hand column.
3. Double click Universal Serial Bus Controllers.
4. Look for an entry for Data logger Interface.
5. If the entry is present, and there are no warning messages or icons, then windows has correctly
recognized the connected RFC1000.
6. If the entry is not present, or has an exclamation point icon next to it, the USB drivers may need to
be installed. These are available on the software flash drive included with the RFC1000, and on the
MadgeTech website.
Ensure that the USB end of the RFC1000 is securely connected to the computer.
1. Locate the USB-A plug of the RFC1000.
2. If the interface cable is connected to the PC, unplug it. Wait ten seconds.
3. Reconnect the cable to the PC.
4. Check to make sure that the red LED is lit, indicating a successful connection.
DOC 1268036-00 REV 6 2015.01.02