MadgeTech RFPulse2000A User manual

RFPulse2000A
RFPulse2000A
Wireless Pulse Data Logger
Product User Guide
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

Product User Guide
RFPulse2000A Data Logger
Quick Start Steps ........................................... 1
Product Overview .......................................... 2
Additional Features & Operation .................... 3
Mounting Instructions ................................... 4
Product Maintenance ..................................... 5
General Specifications.................................. 6-7
RFC1000 Transceiver
Product Overview .......................................... 9
Installation Guide ........................................... 9
Mounting Instruction ................................... 10
Channel Programming ................................. 11
Deployment & Activation .............................. 12
General Specifications................................... 12
Compliance Information................................ 13
Troubleshooting Tips ............ Back Cover
Table of Contents
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

1
1. Install the MadgeTech 4 Software and USB Drivers onto a Windows PC.
2. The RFC1000 interface device comes with a USB cable. Plug one end of the cable into
an available USB port on the PC and plug the opposite end of the cable into the
communication port on the RFC1000.
3. Push and hold the wireless button on the RFPulse2000A for 5 seconds to activate
wireless communication. The display will confirm “Wireless: ON” and the blue LED
will blink every 15 seconds.
4. Launch the MadgeTech 4 Software. All active MadgeTech Data Loggers that are within
range will automatically appear in the connected devices window. Each data logger in
the list can be identified by serial number (printed on the exterior of the logger).
5. To claim a device, select the desired data logger in the list and click the Claim icon.
6. Select the start method, reading rate and any other parameters appropriate for the
desired data logging application. Once configured, deploy the data logger by clicking
the Start icon.
7. To download data, select the device in the list, click the Stop icon, and then click the
Download icon. A graph will automatically display the data.
Quick Start Steps
1. Install the MadgeTech 4 Software and USB Drivers onto a Windows PC.
2. Before plugging the data logger in the computer, make sure the wireless setting on
the device is set to “Wireless: OFF”. If wireless mode is on, press and hold the Wireless
button on the device for 5 seconds.
3. The RFPulse2000A comes with a USB cable. Plug one end of the cable into an available
USB port on the PC and plug the opposite end of the cable into the communication
port on the RFPulse2000A.
4. Launch the MadgeTech 4 Software. The RFPulse2000A will appear in the connected
devices window indicating the device has been recognized.
5. Select the start method, reading rate and any other parameters appropriate for the
desired data logging application. Once configured, deploy the data logger by clicking
the Start icon.
6. To download data, select the device in the list, click the Stop icon, and then click the
Download icon. A graph will automatically display the data.
Product Operation (Plugged In)
Product Operation (Wireless)
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

Product User Guide
Product Overview
The RFPulse2000A is a wireless data logger that records pulse output signals from various
sensors such as flow meters and anemometers. When started, the data logger samples at
100Hz and at the user specified reading rate.
The RFPulse2000A features a display screen which provides instant access to the current
reading, minimum, maximum and average statistics. Through the software the device
can be programmed to convert the pulse output into a different unit of measure such as
gallons per minute or miles per hour. This information is available on the LCD screen of the
data logger as well as in the software.
The RFPulse2000A is unique in that it not only calculates pulse count, but it also calculates
pulse rate. Engineering units can be programmed into the device as a rate, which allows
the device to calculate the measurement unit in rates per second, minute, hour or per
day. This provides more useful statistics to the user when data logging over long periods
of time.
Selection Buttons
The logger is designed with 3 direct selection buttons: Scroll, Units and Wireless.
• Scroll: Allows user to scroll through current readings, average stats and device status
information displayed on the LCD Screen.
•Units: Allows user to change displayed units of measure to pulses per sec/min/hour/day/
total number of pulses.
•Wireless: Push and hold this button for 5 seconds to activate or deactivate wireless
communication.
•Manual Reset Option: Allows user to manually reset the statistics within the device to 0
without needing to use the MadgeTech software. Any data recorded up to that point is
recorded and saved.
LED Indicators
• Status: Green LED blinks every 5 seconds to indicate unit is logging.
• Wireless: Blue LED blinks every 15 seconds to indicate unit is operating in wireless mode.
• Alarm: Red LED blinks every 1 second to indicate an alarm condition.
Connecting Information
Port Information
The RFPulse2000A data logger terminal ports are located on the bottom of the device, one
positive and one negative. RFPulse2000A provides an internal pull up 2.88V@ 250uA.
Note about polarity: If the input signal has an external power supply, (I.E. a 9V Logic) connect
the (+) to the 9V and the (-) to the ground connection. Maximum input Voltage is 30V. If the
internal pull-up is sufficient, connect the (+) to the internal positive and the (-) to the ground. If
a connection to a switch is desired, either port can be used.
2
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

RFPulse2000A
Additional Features and Operation
Alarm Settings/Rules
In MadgeTech 4, alarms can be created
on two levels; in the software itself, and
programmed specifically to the data logger.
Creating alarm rules in the software allows
the user to utilize alarms while real time
recording, and have the added benefit of
features such as e-mail and SMS notification.
An alarm that is programmed on the data
logger will only alert the user from the
device itself, whether that is by a flashing
LED, audible alarm, or local LCD notification.
Creating a Real time Alarm Rule
1. Within the Device tab in MadgeTech 4, in the Alarms group, click Manage Rules,
then select New.
2. Enter a name in the Rule name box, and select whether notifications will occur when
All conditions are met or Any condition is met.
3. Select the desired conditions to have met before notifications occur, and select which
notifications will occur from the drop down menus.
4. If selecting to receive notifications by email or text message, click Email settings and
make sure the correct info has been entered. Email and text message notifications will
not be received if settings are incorrect.
5. Click OK. The OK button will be disabled if the Rule name box is empty.
Changing the Alarm Settings of a Device
1. In the Connected devices panel, select the RFPulse2000A device.
2. Click the Properties button under the device tab at the top of the software, and select
the Alarm tab in the Properties window.
3. The High and Low settings indicate reading thresholds at which the alarm becomes active.
4. The Delay setting indicates how long to wait before the alarm becomes active after
passing an alarm threshold.
5. The Use cumulative alarm delay checkbox indicates whether the alarm delay should
reset when reading values fall back within the alarm threshold.
6. Once the alarm is configured appropriately, click Apply to save the settings.
**Please refer to the Help file in the MadgeTech software for more information regarding alarm settings**
3
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

Product User Guide
The base provided with the RFPulse2000A can be used in two ways.
• The bottom of the logger snaps in place to use and mount the unit on a table top or
horizontal surface.
• The base can also securely snap to the backside of the logger for wall mounting if desired
(as shown below).
• There are two holes in the base to allow for screws for mounting.
Mounting Instructions
4
Still need help? For more troubleshooting tips and information, refer to the built in help
section of the MadgeTech 4 software, visit our Knowledge Base online at
www.madgetech.com/kbase or contact us for customer support at 603-456-2011.
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

RFPulse2000A
Product Maintenance
Battery Replacement
Materials: U9VL-J Battery
1. On the bottom of the enclosure, open the battery compartment by pulling in on the
cover tab.
2. Remove the battery by pulling it from the compartment.
3. Install the new battery, taking note of the polarity.
4. Push the cover closed until it clicks.
5
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

Product User Guide
Reading Rate 1 reading every second up to 1 reading every 24 hours
Memory 16,128 readings
LED Functionality
• Green LED blinks every 5 seconds to indicate unit is logging
• Blue LED blinks every 15 seconds to indicate unit is in wireless mode
• Red LED blinks every 1 second to indicate alarm condition
Wrap Around Yes
Start Modes Immediate Start & Delay Start
Battery Type Ultralife 9V lithium battery included; user replaceable
Battery Life 5 years typical at 10 minute reading rate
Display Details Displays Pulse/Interval Count & Total Count
Time Accuracy ±1 minute/month
Computer Interface USB to mini USB, 250,000 baud for standalone operation or RFC1000
required for wireless operation
Software XP SP3/Vista/Windows 7/Windows 8 (MadgeTech 4 only)
Operating
Environment -20°C to +60°C (-4°F to +140°F); 0 to 95% RH non-condensing
Dimensions 3.5” x 3.0” x 0.95” (88.9mm x 76.2mm x 24.1mm) - Data logger only
Weight 4.1 oz (0.2563 lbs)
Enclosure Material ABS Plastic
Alarm
User configurable audible, on-screen, email and text (SMS) alarms.
Alarm Delay: A cumulative alarm delay may be set in which the device
will activate the alarm (via LED) only when the device has recorded a
user specified time duration of data.
Audible Alarm
Functionality 1 Beep per second for reading alarm above/below threshold
Overload Protection ±30 Volts (V) for 2 seconds
Approval US (FCC), CA (IC), CE, South Korea (KCC)
RFPulse2000A General Specifications
6
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm
or more should be maintained between the antenna of this device and persons during operation. To ensure compliance,
operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

RFPulse2000A
Sensor Type Channel 1: Ambient; Pulse Detection Circuit
Channel 2: Mathematic; Phantom Total Channel
Response Time 10 microseconds
Input Range 0 to 4,294,967,295 Pulses
RF Frequency 2.45GHz IEEE 802.15.4 ultra-low power MadgeNET wireless
transceiver with fully bi-directional communication
Band ISM band 2.405-2.475 GHz
Operation (channels 11 through 25) @ 250 kbps
Maximum Output
Power +0dBm typical
Receiver Sensitivity
(RFC1000) -95dBm typical
Range 2000’ max. outdoors (line of sight unobstructed)
500’ max. indoors (typical urban)
Transmission Distance
(to other RFC1000’s)
• RFC1000
4,000’ max. outdoors - line of sight unobstructed
1,000’ max. indoors - typical urban environment
• RFC1000-CE
2,500’ max. outdoors - line of sight unobstructed
700’ max. indoors - typical urban environment
• RFC1000-IP69K
4,000’ max. outdoors - line of sight unobstructed
1,000’ max. indoors - typical urban environment
Transmission Distance
(to data loggers)
• RFC1000, RFC1000-CE & RFC1000-IP69K
2,000’ max. outdoors - line of sight unobstructed
500’ max. indoors - typical urban environment
Measurement
Wireless
Battery Warning
WARNING: MAY LEAK, FLAME OR EXPLODE IF DISASSEMBLED, SHORTED, CHARGED,
CONNECTED TOGETHER, MIXED WITH USED OR OTHER BATTERIES, AND/OR EXPOSED TO FIRE/
HIGH TEMPERATURE. DISCARD USED BATTERY PROMPTLY, KEEP OUT OF REACH OF CHILDREN.
Specifications subject to change.
See MadgeTech’s terms and conditions at www.madgetech.com
7
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk

Product User Guide
RFC1000
Wireless Transceiver
8
Other models available:
RFC1000-CE - Approved for
European markets
RFC1000-IP69K - Splash Proof
for harsh environments
Distributor: LoggerShop Technologies | Dorset
Tel: [phone] Fax: [phone] | Email: [email protected] | www.loggershop.co.uk