Magick Woods Elements BRISTOL VANITY 49191 User manual

1: Removing old vanity (if applicable): 1) Turn off the water supply and drain out. 2) Disconnect the supply lines from
the faucet. 3) Remove the old vanity top and vanity. If the new vanity is not installed immediately, temporarily stuff
a rag into the drain pipes.
2: Using a level, locate any uneven oor and/or wall areas where your vanity will be installed. Unevenness can cause
your vanity to become misaligned resulting in twisting of the cabinet. Repair any uneven areas by reducing high spots
or shimming low spots.
3: Provide sufcient protection on the oor to protect the vanity from damage. Tilt the vanity backwards and remove
the shipping feet from the bottom of the vanity base using a pair of pliers (A - not included). Figure 1.
4: 1) Place the vanity in the desired position taking into account the location of your plumbing. 2) Ensure the vanity
is level front to back and at both sides.
5: Secure the vanity to the wall by inserting (x 2) #8 x 2” screws (C - not included) through the back rail of the vanity.
Figure 2. It is recommended that the vanity be installed to at least one wall stud. If you are unable to locate wall
studs, it is recommended that you use wall anchors (D - not included) to secure the vanity.
6: Attach the (x 2) knobs by using (x 2) 1” screws. Figure 3.
7: 1) Place the sink upside down (provide sufcient protection on the oor to protect the sink from damage).
2) Sit the nylon bush (chamfer face down) and the gasket on the drainer body. Figure 4. 3) Insert the drainer
body through the sink drain hole with the bottom of the drainer body facing upward.
8: Fasten the jamb locknut onto the drainer body threads, turning counter-clockwise and
hand-tighten. Figure 5.
9: 1) Place the washer onto the drainer body over the jamb locknut. 2) Fasten the drain pipe coupler onto the
drainer body threads (overtop of the washer), turning counter-clockwise and hand-tighten. Figure 6.
10: Fasten the tail piece onto the drain pipe coupler threads, turning counter-clockwise and hand-tighten.
Figure 7.
11: Return the sink facing upward and place the sink centered on the vanity base. Figure 8. For additional
stability, clear silicone (E - not included) may be used to secure the sink onto the vanity base (optional).
12: Sit the strainer into the strainer hole located on the top of the sink. Figure 9.
13: Connect the faucet and the remainder of the plumbing components as per the instruction sheets provided
with those items and ensure that there is no leakage. If required, clear silicone (E - not included) can be applied.
Tools required for assembly
(not included):
• pliers (A)
• tape measure
• electric drill with #2 drill bit (B)
• level
• (x 2) #8 x 2” screws (C)
• (x 2) wall anchors - if the
vanity will not be screwed
to wall studs (D)
• silicone (optional) (E)
Estimated installation time:
2-1/2 hours (including removal
of old vanity if applicable)
PREPARATION
INSTALLATION
PACKAGE CONTENTS
CARE & MAINTENANCE
• To maintain the beauty of the furniture nish, avoid placing the vanity in direct sunlight.
• Avoid exposing the vanity to extreme temperatures by installing away from heat and air vents.
• Dust frequently with a clean, soft and dry cloth.
• Wipe away any water or liquid spills on the vanity base immediately with a clean, soft and
dry cloth.
• Clean the sink only with non-abrasive cleaners or mild detergents - do not use powder
cleansers. For extremely stubborn stains, use a small amount of acetone on a cloth and gently
rub out the stain.
Base (x 1)
1” screws (x 2)
Knobs (x 2)
Bumpers (x 4)
Sink Drain
Assembly (x 1) Strainer (x 1)
Tail Piece
(x 1)
Figure 1
A
B
C
Figure 2
Figure 3
B
Faucet not included.
BRISTOL VANITY ENSEMBLE
MODEL 49191 • INSTALLATION INSTRUCTIONS
Sink (x 1)
Questions? Call our customer service department at 1-855-995-5578, 8:30 a.m. - 5 p.m., EST, Monday - Friday or e-mail: [email protected].
WARNINGS & CAUTIONS
WARNING:
Two people are required for safe installation. Take extra precautionary measures to
ensure a secure grip on the vanity base and sink when lifting.
CAUTION:
• The bathroom oor and wall must be nished prior to installation of the base
and sink.
• Do not use water that exceeds temperatures of 140°F/46°C.
• Do not place any sharp or abrasive objects on the bare surface of the sink.
Drain Pipe Coupler
Washer
Jamb Locknut
Nylon Bush
Rubber Gasket
Drainer Body
Sink (Bottom View)
PARTS FOR SINK DRAIN ASSEMBLY
Chamfer Face Down
Nylon Bush
Rubber Gasket
Drainer Body
Sink Hole
Sink
(Bottom View)
Figure 4
OVERALL DIMENSIONS (WITH SINK):
30-1/8” W x 34-1/4” H x 19-1/8” D
76.51 cm W x 86.99 cm H x 48.57 cm D

Figure 10
Bumper
Figure 11: Assembled
Bumper
Sink: Bottom View
Jamb Locknut
Nylon Bush,
Rubber Gasket
& Drainer Body
After Assembly
Figure 5
Drain Pipe Coupler
Washer
Jamb Locknut,
Nylon Bush,
Rubber Gasket
& Drainer Body
After Assembly
Figure 6
View with Sink
Figure 7
Tail Piece
Figure 8
Strainer
Figure 9
TROUBLESHOOTING
Problem: 1) Vanity doors rub against
another surface.
2) There is a large uneven gap
between the doors and cabinet.
Possible Cause: Floor is not level.
Corrective Action: 1) Use a shim
to ensure the vanity is level.
2) Adjust the door hinges.
Problem: Sink wobbles when placed
on the vanity base.
Possible Cause: 1) The vanity base
is not installed level and plumb.
2) The under side of the sink is
uneven: this can be a common
occurrence in porcelain sinks due
to the manufacturing process.
Corrective Action: 1) Ensure the
vanity base is level and plumb. It
may be necessary to use shims if
the base sits uneven (see Step 2
in the Installation section).
2a) Identify which corners have the
wobble. 2b) Carefully remove the
sink and turn it over.
2c) Apply the bumpers adhesive side
down on the corners of the sink that
you identied in Step 2a. Figure 10.
2d) Carefully place the sink back
onto the vanity base and make any
necessary adjustments to the bumper
placement(s) until the sink does not
wobble.
WARRANTY
All products should be checked for
defects or damages prior to installation
and any defects or damages should be
notied to Magick Woods Exports Pvt. Ltd.
What This Warranty Covers:
Magick Woods Exports Pvt. Ltd.
warrants its products to be free from
substantial defects in materials and
workmanship from the original date of
purchase under normal home use. This
warranty is offered only to the original
consumer purchaser and may not be transferred.
Magick Woods Exports Pvt. Ltd. is only
responsible for the actual purchase price.
How Long The Warranty Lasts:
Coverage for all vanity cabinets, xed vanities, drawer
banks, bath storage cabinets, linen cabinets, wall hutches,
llers, toe kicks, medicine cabinets, mirrors and accessories
lasts from 3 years from the original date of purchase.
Coverage for all porcelain sinks lasts from 1 year from the
original date of purchase.
What Magick Woods Exports Pvt. Ltd. Will Do Under
The Warranty:
During the warranty period, Magick Woods Exports Pvt. Ltd.,
at its option, will repair or replace any part or product that
proves to have substantial defects in materials or
workmanship, or Magick Woods Exports Pvt. Ltd.
will provide an equivalent replacement product.
Magick Woods Exports Pvt. Ltd. reserves
the right to change specications in
design and materials without notice and
with no obligation to replace products
that were previously manufactured.
Implied Warranties: Magick Woods
Exports Pvt. Ltd. disclaims any implied
warranty of merchantability, and there are
no warranties that extend beyond the
descriptions on the face hereof.
Wood, Aging and Appearing in Printed Materials:
Because of the varying natural characteristics of wood
and the effects of aging, product shown in displays and/or printed materials (such as product photos printed in brochures, iers, catalogs,
etc.) will not be an exact match to the cabinetry you will receive. Depending on the wood characteristics, the age of a sample and the
environment of the showroom, samples will show some degree of variation from new product. In addition, you should not expect all doors,
drawer fronts, trim, or moulding to match exactly in either nish or grain. Variation in wood is normal and unavoidable. In addition, it is not
possible to exactly match our colors in printed materials. Therefore, you should view the actual samples when making your color selection.
What This Warranty Does Not Cover: This warranty does not cover any problems or damage which result from improper transportation,
improper installation, mishandling, misuse, abuse, neglect, abnormal use, commercial use, improper maintenance, unauthorized repairs,
accidents, or acts of God, such as hurricanes, re, earthquakes or oods. The warranty and any applicable implied warranties do not
cover incidental or consequential damages arising from any defects in the product such as labor charges for installation or removal of
the product or any associated products. Magick Woods Exports Pvt. Ltd. is not responsible for any installation charges. For all bath
furniture: This warranty does not cover defects or damage caused by normal wear and tear, alterations, environmental conditions, humidity
absorption, or mold. In addition, variations in wood grain, nish color, aging, or other natural wood stain characteristics are not considered defects
and are not covered by this warranty. For all porcelain sinks: This warranty does not cover defects or damage caused by normal wear and tear,
alterations, environmental conditions, or misuse including placing sharp or abrasive objects on the sink surface, cleaning the sink with abrasive tools or cleansers, dropping any large or
heavy objects onto the sink, or using water that exceeds a temperature of 140o Fahrenheit/46oCelsius.
How to Obtain Warranty Service: If you need replacement parts or would like to make a warranty claim, please contact our Customer Service Representative by mail, email, fax, or
telephone at the address, email or telephone/fax number listed. All warranty claims must include the model number of the product, copy of the original receipt, and the nature of the
problem. In addition, Magick Woods Exports Pvt. Ltd. may at its discretion require inspection of the installation site, photography, or authorize the prepaid return of the claimed defective
part. Merchandise not pre-approved for return will not be accepted and the associated claim not accepted. If upon inspection you nd your product is damaged or missing parts, it is not
necessary to return the unit to the store of purchase. Please contact Magick Woods Exports Pvt. Ltd. Customer Service to obtain a replacement part.
Magick Woods Exports Pvt. Ltd. Customer Service: Phone: [phone] • Fax: [phone] • Email: [email protected]
REPLACEMENT PARTS
Door: R16945 Sink/top: R87261
Door hinges (x 2): R16946 Sink strainer: R31010
Door knob (with screws): R31017 Sink drain pipe: R31011