Magick Woods Elements GENEVA 30234 User manual

PACKAGE CONTENTS Vanity top, faucet and drain not included.
GENEVA VANITY BASE
INSTALLATION INSTRUCTIONS
White models: 30234, 30235, 30236, 30237, 30238, 30239
Gray models: 30242, 30243, 30244, 30245, 30246, 30247
Questions? Call our customer service department at 1-855-995-5578, 8:30 a.m. - 5 p.m., CST,
Monday - Friday or e-mail: [email protected].
Tools required for assembly (not included):
• tape measure
• electric drill with #2 drill bit (A)
• level
• (x2) #8 x 2” screws (B)
• (x2) wall anchors - if the vanity will not be screwed to wall studs (C)
Estimated installation time: 2-1/2 hours (including removal of
old vanity if applicable)
PREPARATION
White model - 30237
Gray model - 30245
48”W x 34-1/2”H x 21-3/4”D
White model - 30238
Gray model - 30246
60”W x 34-1/2”H x 21-3/4”D
White model - 30239
Gray model - 30247
60”W x 34-1/2”H x 21-3/4”D
White model - 30235
Gray model - 30243
30”W x 34-1/2”H x 21-3/4”D
White model - 30234
Gray model - 30242
24”W x 34-1/2”H x 21-3/4”D
White model - 30236
Gray model - 30244
36”W x 34-1/2”H x 21-3/4”D
Base (x1) Base (x1) Base (x1)
Base (x1) Base (x1) Base (x1)
WARNINGS & CAUTIONS
WARNING:
Two people are required for safe installation. Take
extra precautionary measures to ensure a secure
grip on the vanity base when lifting.
CAUTION:
The bathroom oor and wall must be nished prior
to installation of the vanity base.
CARE & MAINTENANCE
• To maintain the beauty of the furniture nish, avoid placing the vanity in direct sunlight.
• Avoid exposing the vanity to extreme temperatures by installing away from heat and air vents.
• Dust frequently with a clean, soft and dry cloth.
• Wipe away any water or liquid spills on the vanity base immediately with a clean, soft and dry cloth.

Figure 1
NOTE: Recommended bowl
depth is less than or equal to
5-1/2”.
1: Removing old vanity (if applicable): 1) Turn o󰀨 the water
supply and take the drain out. 2) Disconnect the supply lines from
the faucet. 3) Remove the old vanity top and vanity. NOTE: If the
new vanity is not installed immediately, temporarily stu󰀨 a rag into
the drain pipe.
2: Using a level, locate any uneven oor and/or wall areas where
your vanity will be installed. Unevenness can cause your vanity
to become misaligned resulting in twisting of the cabinet. Repair
any uneven areas by reducing high spots or shimming low spots.
3: 1) Place the vanity in the desired position taking into account
the location of your plumbing. 2) Ensure the vanity is level front to
back and at both sides.
4: Secure the vanity to the wall by inserting (x2) #8 x 2” screws
(B - not included) through the back rail of the vanity. Figure 1.
NOTE: It is recommended that the vanity be installed to at least
one wall stud. If you are unable to locate wall studs, it is
recommended that you use wall anchors (C - not included) to
secure the vanity.
5: Install the vanity top, faucet and drain (each not included) as
per the instruction sheets provided with those items and ensure
that there is no leakage.
INSTALLATION Model 30237 shown in illustrations
A
A
TROUBLESHOOTING
Problem:
1) Vanity doors or drawers rub against
another surface.
2) There is an uneven gap between the
doors or drawers and cabinet.
Possible Cause:
Floor or vanity is not level.
Corrective Action:
1) Use a shim to ensure the vanity is level.
2) Adjust the door hinges or drawer slides.
Figures 2 and 3.
Side adjustment:
Using a Phillips screwdriver, rotate screw
(1) clockwise to move the door left and
counter-clockwise to move the door right.
Moves the door up to 2 mm.
Depth adjustment:
Using a Phillips screwdriver, rotate screw
(2) clockwise to move the door forward and
counter- clockwise to move the door backwards.
Moves the door up to 2 mm.
Height adjustment:
Using a Phillips screwdriver, rotate screw
(3) clockwise to move the door upward and
counter-clockwise to move the door
downward. Moves the door up to 2 mm.
Figure 2 - Adjusting Hinges

WARRANTY
All products should be checked for defects or damages prior to installation and any defects or damages should be notied to Magick Woods Exports Pvt. Ltd.
What This Warranty Covers: Magick Woods Exports Pvt. Ltd. warrants its products to be free from substantial defects in materials and workmanship
from the original date of purchase under normal home use. This warranty is o󰀨ered only to the original consumer purchaser and may not be transferred.
Magick Woods Exports Pvt. Ltd. is only responsible for the actual purchase price.
How Long The Warranty Lasts: Coverage for all vanity cabinets, xed vanities, drawer banks, bath storage cabinets, linen cabinets, wall hutches,
llers, toe kicks, medicine cabinets, mirrors, and accessories lasts from 3 years from the original date of purchase.
What Magick Woods Exports Pvt. Ltd. Will Do Under The Warranty: During the warranty period, Magick Woods Exports Pvt. Ltd., at its option, will
repair or replace any part or product that proves to have substantial defects in materials or workmanship, or Magick Woods Exports Pvt. Ltd. will provide
an equivalent replacement product. Magick Woods Exports Pvt. Ltd. reserves the right to change specications in design and materials without notice
and with no obligation to replace products that were previously manufactured.
Implied Warranties: Magick Woods Exports Pvt. Ltd. disclaims any implied warranty of merchantability, and there are no warranties that extend beyond
the descriptions on the face hereof.
Wood, Aging and Appearing in Printed Materials: Because of the varying natural characteristics of wood and the e󰀨ects of aging, product shown in
displays and / or printed materials (such as product photos printed in brochures, iers, catalogs, etc.) will not be an exact match to the cabinetry you will
receive. Depending on the wood characteristics, the age of a sample and the environment of the showroom, samples will show some degree of variation
from new product. In addition, you should not expect all doors, drawer fronts, trim, or moulding to match exactly in either nish or grain. Variation in wood
is normal and unavoidable. In addition, it is not possible to exactly match our colors in printed materials. Therefore, you should view the actual samples
when making your color selection.
What This Warranty Does Not Cover: This warranty does not cover any problems or damage which result from improper transportation, improper
installation, mishandling, misuse, abuse, neglect, abnormal use, commercial use, improper maintenance, unauthorized repairs, accidents, or acts of
God, such as hurricanes, re, earthquakes or oods. The warranty and any applicable implied warranties do not cover incidental or consequential
damages arising from any defects in the product such as labor charges for installation or removal of the product or any associated products. Magick
Woods Exports Pvt. Ltd. is not responsible for any installation charges. This warranty does not cover defects or damage caused by normal wear and tear,
alterations, environmental conditions, humidity absorption, or mold. In addition, variations in wood grain, nish color, aging, or other natural wood stain
characteristics are not considered defects and are not covered by this warranty.
How to Obtain Warranty Service: If you need replacement parts or would like to make a warranty claim, please contact our Customer Service
Representative by email, fax, or telephone at the email or telephone / fax numbers listed. All warranty claims must include the model number of the
product, copy of the original receipt, and the nature of the problem. In addition, Magick Woods Exports Pvt. Ltd. may at its discretion require inspection
of the installation site, photography, or authorize the prepaid return of the claimed defective part. Merchandise not pre-approved for return will not be
accepted and the associated claim not accepted. If upon inspection you nd your product is damaged or missing parts, it is not necessary to return the
unit to the store of purchase. Please contact Magick Woods Exports Pvt. Ltd. Customer Service to obtain a replacement part.
Magick Woods Exports Pvt. Ltd. Customer Service:
Phone: [phone] • Fax: [phone] • Email: [email protected]
Front slope angle adjustment:
Using a Phillips head screwdriver, rotate screw (4) clockwise to tilt the
drawer up, up to 4 mm.
Drawer front removal:
Using a Phillips head screwdriver, flip up the lever and rotate screw (3)
clockwise for both sides to remove the drawer front out from the drawer box.
Up & down adjustment:
Using a Phillips head screwdriver, rotate screw (2) clockwise to move the
drawer up and counter clockwise to move the drawer down, up to 2 mm.
Left & right adjustment:
Using a Phillips head screwdriver, rotate screw (1) clockwise to move the
drawer front left and counter clockwise to move the drawer front right, up
to 1 mm.
Figure 3 - Adjusting Drawers

GENEVA COLLECTION
SKU # 605-4788
60"W x 34-1/2"H x 21-3/4"D
60" Geneva single-bowl vanity base
60"
Product Specifications:
Replacement parts:
1. R18244 - Left door - (503 x 302 x 18)
2. R18230 - Right door - (503 x 302 x 18)
3. R18249 - Bottom drawer front - (454 x 250 x18)
4. R18242 - Top drawer front left & right - (454 x 503 x 18)
5. R18226 - Mid drawer front - (607 x 250 x 18)
6. R37628 - Hinge 'O' slow close 52cc taiming
7. R37629 - Hinge fixing plate with screw
8. R37614 - Female assembly bracket - CP6721122G
9. R37615 - Male assembly bracket - CP672112G
10. R31222 - 808-185 x 400mm slim meta box gray SC
11. R31223 - 808-89 x 400mm slim meta box gray SC
12. R31217 - U-shape plastic 240 x 130 x 83 gray (HT-01.U01)
13. R37027 - CSK (No:8) 3.5 x 16mm star head-913799200
14. R31206 - 4x16 pan head screw w/extended pitch
15. R37421 - Euro head screw 6.3 x 12.5mm - 921985100
• 2 soft-close doors and 5 drawers
• Cabinet interior in matte white finish,
drawer box (excluding drawer front) in warm gray finish
• Cabinet exterior: matte gray finish
• Doors and drawers: high gloss gray finish
• On-trend handeless j-pull door/drawer design
• The 2 doors have the appearance of 4 drawers/
2 deep drawers have the appearance of 4 drawers
• Vanity top, faucet and drain not included