Magiglo ACCOLADE User guide

Users,
Installation & Servicing
Instructions
MUST BE LEFT WITH THE USER
ACCOLADE
Fuel Effect Options:
Coal Effect – NG and LPG
Pebble Effect – NG and LPG
Control Options:
Manual BM Control
Upgradeable Manual Control
Remote Control
Optimum Control
For use on Natural Gas (G20) at a supply pressure of 20mbar
or Propane (G31) at a supply pressure of 37mbar in GB and IE
(Dependent upon model)

Manufacturer Contact Details:
Burley Appliances Ltd
Lands End Way
Oakham, Rutland, LE15 6RB
Tel: [phone]
Fax: [phone]
General E-Mail: [e-mail]
Web Site: www.magiglo.co.uk
Technical Support: Direct Dial on [phone] or email: [e-mail]
Burley Magiglo Document Number:
MF420.61 CAS
Revision Date:
15 October 2009
Copyright:
This documentation is copyrighted by Burley Appliances Ltd. ©2009.
No part of this document may be copied, photocopied or reproduced in any form or by any
means without permission in writing from Burley Magiglo.
Burley Magiglo is a registered trademark of Burley Appliances Ltd.
Service Warranty:
In the unlikely event of a defect in materials or workmanship occurring within one year of
purchase, Burley Magiglo will arrange to repair or replace the item free of charge.
Any claims under this warranty must be made through the retailer from whom the product
was purchased.
As the purchaser’s contract of sale is with the retailer, Burley Magiglo are unable to enter
into discussions with the purchaser until the retailer has inspected any claim and deemed
it to be valid.
Burley Magiglo reserve the right to refuse service or make a charge for any service call,
when a defect is due to installation error or misuse.
Extended warranty (if purchased) commences after the first year; please see separate
registration for further information.
Appliance Details:
For future reference, please complete the following information at the time of installation.
Model and Serial Number details may be found on the data plate as shown.
Serial Number
Model
Installation Date
Installed By
Model
Serial
Number

Page i
Contents
1.General Information........................................................................................................... 1
1.1.Important Note About ODS Pilot ................................................................................ 2
1.2.Fire Fret Dimensions .................................................................................................. 3
2.User Instructions ............................................................................................................... 5
2.1.Lighting Procedure ..................................................................................................... 5
2.1.1.Lighting Procedure (Manual BM Control) ............................................................ 6
2.1.2.Lighting Procedure (Upgradeable Manual Control) ............................................. 7
2.1.3.Lighting Procedure (Remote Control) .................................................................. 8
2.1.4.Lighting Procedure (Optimum Control) ................................................................ 9
2.2.Battery Replacement (Remote Control) ................................................................... 10
2.2.1.Handset.............................................................................................................. 10
2.2.2.Receiver Unit ..................................................................................................... 10
2.3.Battery Replacement (Optimum Control) ................................................................. 12
2.4.Fuel Effect Layout .................................................................................................... 13
2.4.1.Coal Effect Layout.............................................................................................. 14
2.4.2.Pebble Effect Layout.......................................................................................... 16
2.5.Fitting a Standard Trim (If supplied) ......................................................................... 17
2.6.Fitting an ioss Firebox Fascia (if supplied)............................................................... 17
2.7.Home Improvements ................................................................................................ 18
2.8.Cleaning and Care Instructions ................................................................................ 19
2.8.1.Cleaning the Fire-Bed and the Imitation Coals/Pebbles .................................... 19
2.8.2.Cleaning the Pilot............................................................................................... 20
2.8.3.Cleaning the Fire Back....................................................................................... 20
2.8.4.Black Painted Metal Surfaces ............................................................................ 20
2.8.5.Brass or Polished Surfaces................................................................................ 22
2.8.6.Stainless Steel ................................................................................................... 22
2.8.7.Care of Ceramic Backs ...................................................................................... 22
3.Installation Instructions .................................................................................................. 23
3.1.General Safety Requirements .................................................................................. 23
3.2.Flue Requirements ................................................................................................... 23
3.3.General Dimensions................................................................................................. 25
3.4.Appliance Location ................................................................................................... 25
3.4.1.Floor Level and Raised Fireplace Openings...................................................... 26
3.4.2.Physical Barrier.................................................................................................. 27
3.5.Ventilation................................................................................................................. 30
3.6.Technical Data ......................................................................................................... 30
3.7.Pressure Test Point Location ................................................................................... 30
3.8.Contents Checklist ................................................................................................... 31
3.9.Installation Procedure............................................................................................... 32
3.9.1.Preparing the Firebox ........................................................................................ 32
3.9.2.Fitting the Flue Restrictor................................................................................... 33
3.9.3.Preparing the Fireplace Opening ....................................................................... 33
3.9.4.Installing the Firebox.......................................................................................... 34
3.9.5.Connecting the Gas Supply ............................................................................... 35
3.9.6.Continuation of Installation - Remote Control Model ......................................... 36
3.9.7.Continuation of Installation - Optimum Control Model ....................................... 37
3.9.8.Commissioning .................................................................................................. 38
3.9.9.Checking for Spillage ......................................................................................... 39
3.9.10.Instructing the User............................................................................................ 39
4.Servicing Instructions ..................................................................................................... 40

Page ii
4.1.General Requirements ............................................................................................. 40
4.2.Servicing Instructions ............................................................................................... 40
4.3.Replacing Parts ........................................................................................................ 41
4.3.1.Pilot Assembly Replacement ............................................................................. 41
4.3.2.Injector Replacement ......................................................................................... 41
4.3.3.Control Valve Replacement ............................................................................... 42
4.3.4.Motor Replacement (Remote Control / Optimum Control Models) .................... 42
4.4.Installation and Operational Troubleshooting........................................................... 43

Page 1
1. GENERAL INFORMATION
Introduction
1. This appliance is suitable for installation in GB and IE and should be installed in
accordance with the rules in force.
In GB, the installation must be carried out by a Gas Safe Registered Installer registered for
working on this type of appliance. It must be carried out in accordance with the relevant
requirements of the:
•Gas Safety (Installation and Use) Regulations.
•The appropriate Building Regulations either The Building Regulations, The
Building Regulations (Scotland), Building Regulations (Northern Ireland).
Where no specific instructions are given, reference should be made to the relevant British
Standard Code of Practice (see item 2).
In IE, the installation must be carried out by a Competent Person and installed in
accordance with the current edition of I.S.813 “Domestic Gas Installations”, the current
Building Regulations and reference should be made to the current ETCI rules for electrical
installation.
On completion of an installation in IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance to I.S.813.
2. The installation of the fire in GB should follow the recommendations of the following
current British Standards:
BS 5871: Pt 2 Installation of Inset Live Fuel Effect Gas Fires
BS 6891 Pipe work Installation
BS 5440: Pts 1 & 2 Flues and Ventilation
BS EN 1856 Chimneys - Requirements for metal chimneys - System chimney
products
BS 715 Metal flue boxes
BS EN 1858 Chimney – Components – Concrete flue blocks
IGE/UP/7 IGE document for gas installations in Timber Frame Buildings
(Available from CORGI or Institute of Gas Engineers)
3. In other EC countries equivalent rules in force must be used.
4. It is important for correct combustion of this fire that the imitation fuel is placed in
accordance with the instructions given in this and associated booklets. Only approved
imitation fuel, available from Burley Magiglo., should be used with this appliance.
5. It is recommended that a fire guard complying with BS 8423 be fitted for the protection of
young children, the elderly or infirm.
6. The user is warned not to throw any rubbish onto the fire or to disturb the fuel bed.
7. The user is advised that the ceramics used within this appliance require extra care whilst
cleaning. Please refer to the Cleaning Instructions.
8. It is important for the fire to be serviced regularly. An annual service is recommended.
Efficiency Declaration
he efficiency of this appliance has been measured as specified in BS 7977-1 and the result of
55.3% (61.3% net) was achieved. The gross calorific value of the fuel has been used for this

Page 2
efficiency calculation. The test data from which it has been calculated has been certified by
Advantica Ltd. The efficiency value may be used in the UK Government’s Standard
Assessment Procedure (SAP) for energy rating of dwellings.
Ventilation Requirements
1. This appliance does not normally require any ventilation in the room it is fitted in. In GB
reference should be made to BS 5871 Part 2, and in IE reference should be made to the
current edition of I.S.813 which makes clear the conditions that must be met to
demonstrate that sufficient ventilation is available.
2. If provided, any purpose provided ventilation must be checked periodically to ensure it is
free from obstructions.
3. When fitting the fire in Northern Ireland (NI), purpose provided ventilation must be
provided in accordance with the rules in force.
4. In other EC countries equivalent rules in force must be used.
Flue Requirements
Class 1 - A flue having no cross sectional dimension less than 175mm (7”) e.g. 225mm
(9”) by 225mm (9”) Masonry chimney or 175mm (7”) diameter clay liner.
Class 2 - A flue having no cross sectional dimension less than 125mm (5”).
Class 2 Pre-cast - A flue constructed of pre-cast concrete/terracotta blocks conforming to
BS EN 1858 or BS 1289: Pt. 1 and having a minimum cross sectional area of 12,272mm2
with the smallest dimension being no less than 63mm.
Please refer to the full Flue and Chimney Requirements within the Installation Instruction
section.
Gas Supply
1. This range of gas fires are suitable for use with either Natural Gas (G20) at 20mbar supply
pressure, or LPG (G31) at 37mbar supply pressure (please check appliance data plate for
compatibility).
2. A separate means of isolating the gas supply should be provided near to the appliance to
facilitate servicing. An isolation valve (with a pressure test point) has been supplied for
this purpose.
Electrical Supply
Not applicable to this range of appliances.
1.1. Important Note About ODS Pilot
This fire is fitted with an ODS pilot which causes the appliance to shut down in the event of a
reduction of oxygen (e.g. caused by poor ventilation) in the room. Should this happen, follow
the lighting instructions to re-light the fire. In the event that the fire should shut down again,
do NOT attempt to re-light it but contact your gas installer for remedial action to be taken.
Under no circumstances should it be adjusted or put out of action by the installer
or the user. In case the pilot needs replacing, only the approved part (available
from your supplier or Burley Magiglo.) should be fitted. Note: if any part of the
pilot assembly becomes faulty the complete assembly will need replacing.

Page 3
1.2. Fire Fret Dimensions
All models can be used with the Burley Magiglo range of frets or any other fire fret that
falls within the dimensions shown below
The fireplace opening must be suitable in size to accommodate the fire being
installed. If the appliance is to be used with other fireplace components, the
installation must allow a minimum of 5 square inches of free air space below the
base of the fire.
Minimum opening
(free air) in fire fret
Minimum opening
(free air) in ash pan cover
Figure 1
Fire Front Specification
Height to Centre (A) Maximum 9 Inches (23cm)
Minimum 7.5 Inches (19cm)
Ash Pan Cover Height (B) Maximum 3.5 Inches (9cm)
Minimum 2.5 Inches (6.4cm)
Ash Pan Cover Free Air Opening Minimum 5 sq. Inches (32.3cm2)
Fire Fret Free Air Opening Minimum 15% of total fire front
area above the base of
the fire
Ash Pan Cover Length (C) Maximum 13.5 Inches (34cm)
Minimum 12.5 Inches (32cm)

Page 4
This page is left intentionally blank

Page 5
2. USER INSTRUCTIONS
2.1. Lighting Procedure
Your fire will be fitted with one of the following different types of gas control valves. Identify the
control system on your fire as shown and follow the appropriate operating instructions in the
appropriate section.
Control Valve Operation Control Type
+
Manual =
Manual BM
Control
See
Section X2.1.1X
on Page X6X
+
Manual =
60BUpgradeable
Manual Control
See
Section X2.1.2X
on Page X7X
+ =
61BRemote Control
See
Section X2.1.3X
on Page X8X
+ =
62BOptimum Control
See
Section X2.1.4X
on Page X9X

Page 6
2.1.1. Lighting Procedure (Manual BM Control)
1. Ensure that the arrow on the control
knob is pointing towards the OFF
position as shown in XFigure 2X. Press in
the knob and slowly turn anti-clockwise
until a click is heard. The spark should
now light the pilot. On first lighting, it
may require several attempts to allow the
pilot light to be purged of air.
2. The pilot can be viewed through the slot
on front panel behind the fire front (See
XFigure 6X).
3. Once the pilot flame is established, hold
the control knob in for approximately 10-
20 seconds and release. The pilot
should now remain alight. Repeat the
procedure if necessary.
4. The arrow should now be pointing to the
PILOT position as shown in XFigure 3X.
5. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.
6. Once the pilot is established, the main
burner can be operated by turning the
control knob anti-clockwise. The preset
minimum is found with the arrow in the 9
o’clock position as shown in XFigure 4X.
7. The preset maximum (as shown in
XFigure 5X) is found by turning the control
knob fully anti-clockwise. The control is
infinitely variable between the two preset
limits.
8. To extinguish the main burner, push the
control knob in and turn clockwise until
the arrow is in the PILOT position, then
release.
9. To extinguish the pilot, push the control
knob in and turn it clockwise until the
arrow is in the OFF position, then
release.
Figure 2 - Off Position
Figure 3 - Ignition Position
Figure 4 - Minimum Position
Figure 5 - Maximum Position
Pilot viewing
slot
Figure 6 - Pilot Viewing Slot

Page 7
2.1.2. Lighting Procedure (Upgradeable Manual Control)
1. Whilst pushing the IGNITION KNOB in
(see XFigure 7X), turn it anticlockwise to
the pilot flame position as shown in
XFigure 8X. During this process, the
spark ignition will have operated and lit
the pilot flame. On lighting the pilot
flame continue to depress the ignition
knob for a further 10 - 12 seconds then
slowly release. The pilot flame should
stay alight. If the flame goes out repeat
the procedure above to establish the
pilot.
2. If the spark unit fails to light the pilot,
the appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
3. Turn the IGNITION KNOB anticlockwise
to the main flame position as shown in
XFigure 9X.
4. Turn the GAS RATE ADJUSTING
KNOB fully anticlockwise (until you
reach the stop position) i.e. the
maximum gas rate. See XFigure 10X.
5. The main burner will have cross-lit from
the pilot.
6. Now the gas rate can be adjusted to the
desired setting by turning the GAS
RATE ADJUSTING KNOB to any
position between the pre-set high and
low.
7. To switch off the main burner turn the
IGNITION KNOB to the ‘Pilot burner
only Position’ as shown in XFigure 8X.
The appliance may be left in this
standby mode if desired.
8. To turn the pilot off turn the Ignition
Knob on the control valve fully
clockwise to ‘¦’ position.
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.
Ignition knob
Gas rate adjusting knob
Figure 7 - Off Position
Figure 8 – Pilot burner only
Figure 9 – Main burner operational, but gas flow off
Figure 10 - Main Burner operational & Maximum Gas
Rate

Page 8
2.1.3. Lighting Procedure (Remote Control)
1. Press the bottom button on the remote
handset until clicking is heard on the
valve, and the gas rate adjustment knob
is at the off position.
2. With gas available at the valve press the
IGNITION KNOB in and turn it
anticlockwise to the pilot flame position.
A click of the piezo igniter will be heard
and a spark will appear at the electrode.
At the same time the gas will flow to the
pilot burner and should be ignited by the
spark. Repeat the procedure until the
pilot flame is established.
3. The pilot can be viewed through the slot
on front panel behind the fire front (See
XFigure 6X).
4. Keep the knob pressed in for a further 10
- 12 seconds and slowly release it. The
pilot flame should stay alight. If the
flame goes out repeat the procedure
above to establish the pilot.
5. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
6. Turn the IGNITION KNOB
anticlockwise to the Main Burner
Operation position as shown in XFigure
11X.
7. Using the HANDSET (as shown in
XFigure 12X) press and hold both the top
and the small button together until the
main burner goes to full rate and clicking
can be heard from the valve. During this
process the main burner will ignite from
the pilot.
8. By pressing the two buttons together (to
increase the gas rate) and the lower
button only (to decrease the gas rate)
the valve can be manipulated to select
the desired gas rate between maximum
and minimum. By pressing the buttons
in short bursts you will be able to adjust
the gas rate in small steps.
9. To turn the fire off, continuously press
the lower button until the flame dies
down and clicks can be heard from the
valve. Release the button as soon as
the clicks are heard.
10. The fire can safely be left in this position
at all times, however to prevent
unauthorised or accidental use (say by
children) it is recommended to turn the
IGNITION KNOB to the pilot flame
position by turning it 90 degrees
clockwise. To turn the pilot off, turn the
IGNITION KNOB fully clockwise.
NOTE: The clicking sound
made by the valve is the
operation of the valve clutch,
and indicates either maximum
or minimum positions.
GAS RATE
AD JU STMEN T
KN O B
PIL O T O N LY
PO SITIO N
IG N IT IO N
KN O B
MAIN BURNER
O PER ATIO N
FU LL R ATE
PO SITIO N
MAIN BURNER
O FF PO SITIO N
Figure 11 – Gas Valve
Press these
two buttons
together to
increase
gas rate
Press this
button to
decrease
gas rate
Figure 12 - Handset Operation
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.

Page 9
2.1.4. Lighting Procedure (Optimum Control)
1. Ensure the main burner is off by pressing
the button on the trim marked
(‘small flame/dot’) until clicking is heard
on the valve (see XFigure 13X).
2. With the gas available at the valve press
in the IGNITION KNOB and turn it
anticlockwise to the pilot flame position
(see XFigure 14X). A click of the piezo
igniter will be heard and a spark will
appear at the electrode. At the same
time the gas will flow to the pilot burner
and will be ignited by the spark. Repeat
the procedure until the pilot flame is
established.
3. The pilot can be viewed through the slot
on front panel behind the fire front (See
XFigure 6X).
4. Keep the knob pressed in for a further 10
- 12 seconds and slowly release. The
pilot flame should stay alight. If the
flame goes out repeat procedure above
to establish the pilot.
5. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
6. Turn the IGNITION KNOB
anticlockwise to the main flame
position.
7. Press and hold the (‘large flame’)
button (in XFigure 13X) until clicking is
heard (fully open).
8. The main burner will have cross-lit from
the pilot.
9. Now the gas rate can be adjusted to the
desired setting by pressing the
(‘small flame/dot’) button. Any rate
between the pre-set high and low can be
obtained using the two buttons.
10. To switch off the main burner press and
hold the (‘small flame/dot’) button
until clicking is heard from the valve
(OFF position).
11. The fire can safely be left in this position
at all times, however to prevent
unauthorised or accidental use (say by
children) it is recommended to turn the
IGNITION KNOB to the pilot flame
position by turning it 90 degrees
clockwise. To turn the pilot off, turn the
IGNITION KNOB fully clockwise.
NOTE: The clicking sound
made by the valve is the
operation of the valve clutch,
and indicates either maximum
or minimum positions.
Figure 13 - Wall Switch
GAS RATE
AD JU STMEN T
KN O B
PIL O T O N LY
PO SITIO N
IG N IT IO N
KN O B
MAIN BURNER
O PER ATIO N
FU LL R ATE
PO SITIO N
MAIN BURNER
O FF PO SITIO N
Figure 14 – Gas Valve
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.

Page 10
2.2. Battery Replacement (Remote Control)
2.2.1. Handset
1. On the reverse of the handset remove
the battery cover by pressing down at
the top of the cover and sliding down.
2. Remove and unclip the old battery and
replace with a new PP3 9V battery.
3. Replace the cover.
Figure 15 – Handset
Press here and
slide down
Figure 16
2.2.2. Receiver Unit
1. Remove the receiver unit from under the
fire burner (or from wherever positioned
if mounted remotely) and remove the
battery compartment cover (see
diagram).
2. Replace the old batteries with new ones,
ensuring they are inserted in the correct
polarity.
3. Replace the cover on the receiver unit,
ensuring that it is securely closed.
4. Return the receiver unit to its original
mounting position.
Figure 17
CAUTION: With the exception of battery replacement, the battery holder must be
located within the heat shield at all times.

Page 11
2.3. Battery Replacement (Optimum Control)
1. The battery pack is mounted inside the
wall-mounting box behind the wall switch
plate.
2. To change the batteries remove the two
small screws securing the wall plate
using a small screwdriver.
3. Remove the battery pack from the wall
box and replace the spent batteries with
new ones (4 off 1.5V AA batteries)
ensuring correct polarity.
4. Insert the battery pack back into the wall
box and refit the wall plate ensuring that
it is the right way up.
5. Secure with screws.
REAR OF WALL
PLATE
CABLE TO
VALVE
BATTERY
PACK
(4 x 1.5 V AA
BATTERIES)
LOW/OFF
SWITCH
HIGH
SWITCH
brown brown
brown
blue
blue
blue
white
black
Figure 18

Page 12
2.4. Fuel Effect Layout
You fire has been supplied with either Coal or Pebble effect. Please refer to the relevant
section for instructions on how to arrange the imitation fuels.
Fuel Effect Tray Type Refer to
Coal Effect Natural Gas & LPG Section X2.4.1X
Pebble Effect Natural Gas & LPG Section X2.4.2X
It is recommended that the imitation fuel be left alone once the desired flame pattern has been
achieved. Constant moving of the imitation fuel will cause the fuel to disintegrate
and/or cause discolouration.
RCF Advice:
This product may use Components (Coals, Pebbles & Ceramic backs)
containing Refractory Ceramic Fibres (RCF), which are man-made vitreous
silicate fibres. Excessive exposure to this material may cause irritation to eyes,
skin and respiratory tract.
Therefore during installation and servicing we recommend that you use a HEPA
filtered vacuum to remove any dust and soot accumulated in and around the fire
before and after working on the fire, to ensure that the release of fibres from
these RCF articles is kept to a minimum.
We recommend that you should follow the normal hygiene rules of not smoking,
eating or drinking in the work area.
When replacing Components containing Refractory Ceramic Fibres (RCF), we
recommend that the replaced items are not broken up, but are sealed within
heavy duty polythene bags, and clearly labelled as RCF waste. RCF waste may
be disposed of in suitably licensed landfill sites.
WARNING: Do not touch the fire when it is alight. The fire will remain very hot for
a while after extinguishing.
Some sooting on the pebbles may be observed. This is perfectly normal.
Periodically operating the Fire at various rates will burn this soot away. If
excessive sooting is observed, this is an indication that the pebbles are laid
incorrectly – please refer to instructions.

Page 13
2.4.1. Coal Effect Layout
This fire is supplied with different sizes of
ceramic coals as follows:
Qty
Small Coals 6
Large Rounded Coals 4
LargeTriangular Coals 3
Rear matrix 1
Front matrix 1
Proceed with the layout as follows:
1. Position the rear matrix behind the
burner as shown in XFigure 19X.
2. Position the front matrix in front of the
burner and ensure that it rests on the
base (see XFigure 20X).
3. Position two Large Rounded coals on
the two ends of the front matrix as shown
in XFigure 21X. Ensure that the flat faces
on the coals are facing into the fire,
vertical and level with the inner face of
the matrix.
4. Place the other two Large Rounded
coals in the middle of the matrix (see
XFigure 22X) such that the flat face of the
coals are bridging between the front
matrix and the rear matrix (see XFigure
23X). XFigure 24Xshows how not to lay the
rounded coals.
5. Bridge the three Large Triangular
coals between the rear matrix and the
rounded coals such that the points of the
triangular shapes on the underside of the
coals are facing forward. (See XFigure
25X).
6. Place the 6 Small coals around the sides
and the back as shown in XFigure 26X.
7. Gently tip the middle two rounded coals
forward so that the flat faces are
distanced away from the rear matrix by
about 10mm (see XFigure 27X).
8. After the appliance has been allowed to
warm up, small adjustments (using a pair
of tongs) may be made to the coals to
achieve the desired flame picture.
9. It is recommended that the coals be left
alone once the desired flame picture has
been achieved. Constant moving of
the coals causes the coals to
disintegrate and/or cause
discolouration.
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24

Page 14
Figure 25
Figure 26
Gap
Tip
Forward
Figure 27
WARNING: Do not touch the
fire when it is alight. The fire
will remain very hot for a while
after extinguishing.

Page 15
2.4.2. Pebble Effect Layout
The fire is supplied with ceramic pebble sets
as follows:-
Qty
Large Pebbles (A, B, K, L & M) 7
Small Pebbles (E & G) 6
Rear Matrix 1
Front Matrix 1
NOTE: When placing pebbles on the tray
ensure the lettering on them is facing down
and into the fire. After every step of pebble
laying ensure that they are stable.
Proceed with the pebble layout as follows:-
1. Position the rear matrix behind the
burner as shown in XFigure 28X.
2. Position the front matrix in front of the
burner and ensure that it rests on the
base (see XFigure 29X).
3. Place pebbles K, L & M in the order
shown in XFigure 30Xsuch that they are
bridging between the front and rear
matrix.
4. Place pebbles A & B on the rear matrix
as shown in Figure 8 such that they are
supported in front by the pebbles laid in
step 3.
5. Place the E & G pebbles on the sides
and around the back as shown in XFigure
31X.
6. After the appliance has been allowed to
warm up, small adjustments (using a
small pair of tongs) may be made to the
pebbles to achieve the desired flame
picture.
7. It is recommended that the pebbles be
left alone once the desired flame pattern
has been achieved. Constant
movement of the pebbles causes the
pebbles to disintegrate and/or cause
discolouration.
WARNING: Do not touch the
fire when it is alight. The fire
will remain very hot for a while
after extinguishing.
Figure 28
Figure 29
A & 2xB
KK
LM
Figure 30
EE
G
Figure 31

Page 16
2.5. Fitting a Standard Trim (If supplied)
1. Most trims are coated with a protective
film. This must be removed by peeling
off before fitting the trim.
2. The trim is held on by four magnets.
These will either be attached to the trim
or supplied loose in a separate envelope.
Space them as shown in XFigure 32X.
3. Offer the trim onto the flange of the
firebox. The magnets will hold the trim in
position.
4. Centralise the trim as necessary.
Magnets
Figure 32
2.6. Fitting an ioss Firebox Fascia (if supplied)
1. The Fascia is coated with a protective
film. This must be removed by peeling
off before fitting the fascia.
2. The fascia is held on by four magnets.
These will either be attached to the trim
or supplied loose in a separate envelope.
Position them as shown in XFigure 33X.
3. Offer the fascia onto the flange of the
firebox. The magnets will hold the fascia
in position.
4. Centralise the trim as necessary.
5. The removable cover can be lifted off to
access the controls.
MAGNETS
Removable
cover to access
controls
MAGNETS
Figure 33