Magiglo DUO POWER SV Series User guide

Users,
Installation & Servicing
Instructions
MUST BE LEFT WITH THE USER
DUO POWER SV
Please Note: These instructions do not cover Duo Power 2 models
Models:
SV – Side and Top Venting
Fuel Effect Options:
Coal Effect
Pebble Effect
Both available on NG & LPG
Control Options:
Manual Control
Installation Options:
Installation using Freedom Surround
For use on Natural Gas (G20) at a supply pressure of 20mbar
or Propane (G31) at a supply pressure of 37mbar in GB and IE
(Dependent upon model)

Manufacturer Contact Details:
Burley Appliances Ltd.
Lands End Way
Oakham, Rutland, LE15 6RB
Tel: [phone]
Fax: [phone]
General E-Mail: [e-mail]
Web Site: www.magiglo.co.uk
Technical Support: Direct Dial on [phone] or email: [e-mail]
Burley Magiglo Document Number:
BMF167.121CAS
Revision Date:
23 September 2009
Copyright:
This documentation is copyrighted by Burley Magiglo. ©2009.
No part of this document may be copied, photocopied or reproduced in any form or by any
means without permission in writing from Burley Magiglo.
Magiglo is a registered trademark of Burley Appliances Ltd.
Service Warranty:
In the unlikely event of a defect in materials or workmanship occurring within one year of
purchase, Burley Magiglo will arrange to repair or replace the item free of charge.
Any claims under this warranty must be made through the retailer from whom the product
was purchased.
As the purchaser’s contract of sale is with the retailer, Burley Magiglo are unable to enter
into discussions with the purchaser until the retailer has inspected any claim and deemed
it to be valid.
Burley Magiglo reserve the right to refuse service or make a charge for any service call,
when a defect is due to installation error or misuse.
Extended warranty (if purchased) commences after the first year; please see separate
registration for further information.
Appliance Details:
For future reference, please complete the following information at the time of installation.
Model and Serial Number details may be found on the data plate as shown.
Serial Number
Model
Installation Date
Installed By
Model
Serial
Number

Page i
Contents
1.General Information........................................................................................................... 1
1.1.Important Note About ODS Pilot ................................................................................ 3
1.2.Fire Fret Dimensions .................................................................................................. 4
2.User Instructions ............................................................................................................... 5
2.1.Lighting the Pilot......................................................................................................... 5
2.2.Lighting the Main Burner ............................................................................................ 6
2.3.Turning the Fan Off .................................................................................................... 6
2.4.Fuel Effect Layout ...................................................................................................... 7
2.4.1.Coal Effect Layout................................................................................................ 8
2.4.2.Pebble Effect Layout............................................................................................ 9
2.5.Fitting Standard Trim (if supplied) ............................................................................ 10
2.6.Fitting ioss Fascia (if supplied) ................................................................................. 10
2.7.Home Improvements ................................................................................................ 11
2.8.Cleaning and Care Instructions ................................................................................ 12
2.8.1.Cleaning the Fire-Bed and the Imitation Coals/Pebbles .................................... 12
2.8.2.Cleaning the Pilot............................................................................................... 13
2.8.3.Cleaning the Fire Back....................................................................................... 13
2.8.4.Painted Metal Surfaces...................................................................................... 13
2.8.5.Brass or Chrome Surfaces................................................................................. 14
2.8.6.Stainless Steel ................................................................................................... 14
2.8.7.Care of Ceramic Backs ...................................................................................... 14
3.Installation Instructions .................................................................................................. 15
3.1.General Safety Requirements .................................................................................. 15
3.2.General Dimensions................................................................................................. 15
3.2.1.Dimensions for Standard Duo Power (excluding Freedom Surround)............... 15
3.2.2.Additional Dimensions for Duo Power with Freedom Surround......................... 16
3.3.Appliance Location ................................................................................................... 17
3.3.1.Floor Level and Raised Fireplace Openings...................................................... 18
3.3.2.Physical Barrier.................................................................................................. 19
3.3.3.Flue Terminal Location ...................................................................................... 21
3.4.Ventilation................................................................................................................. 22
3.5.Technical Data ......................................................................................................... 22
3.6.Contents Checklist ................................................................................................... 23
3.7.Installation Procedure (Examples) ........................................................................... 24
3.7.1.Examples of Installation (without Freedom Surround)....................................... 24
3.7.2.Examples of Installation with Freedom Surround .............................................. 25
3.8.Installation Procedure............................................................................................... 27
3.8.1.General Assembly.............................................................................................. 27
3.8.2.Examples of Flueing Options............................................................................. 28
3.8.3.Spare Parts ........................................................................................................ 29
3.8.4.Preparing the fireplace....................................................................................... 30
3.8.5.Preparation for Installation (all Models) ............................................................. 30
3.8.6.Installing the fire without Freedom Surround ..................................................... 31
3.8.7.Installing the fire with Freedom Surround .......................................................... 31
3.8.8.Preparing the Flue Ducts (for Hearth Mounting) ................................................ 32
3.8.9.Preparing the Flue Ducts (for Hole in the Wall Mounting) ................................. 32
3.8.10.Installing the Fan Chamber................................................................................ 33
3.8.11.Installing the Fan Box ........................................................................................ 34
3.8.12.Fitting the Gas Supply........................................................................................ 34
3.9.Completing the Installation ....................................................................................... 35
3.9.1.Electrical Wiring ................................................................................................. 35

Page ii
3.9.2.Fitting the Fire Tray............................................................................................ 35
3.9.3.Commissioning the Installation .......................................................................... 36
3.9.4.Checking for Spillage ......................................................................................... 37
3.9.5.Fitting the Terminal Guard ................................................................................. 37
3.9.6.Instructing the User............................................................................................ 37
4.Servicing Instructions ..................................................................................................... 39
4.1.General Requirements ............................................................................................. 39
4.2.Servicing Instructions ............................................................................................... 39
4.2.1.Fan and Flue Servicing ...................................................................................... 39
4.2.2.Cleaning the Fan Impeller.................................................................................. 39
4.2.3.Servicing the Fire ............................................................................................... 39
4.3.Replacing Parts ........................................................................................................ 40
4.3.1.Removing the Fire Tray ..................................................................................... 40
4.3.2.Fire Back Replacement...................................................................................... 40
4.3.3.Pilot Assembly Replacement ............................................................................. 41
4.3.4.Injector Replacement ......................................................................................... 42
4.3.5.BM Control Valve Replacement......................................................................... 42
4.3.6.Replacing the Solenoid Valve ............................................................................ 42
4.3.7.Fan Replacement............................................................................................... 42
4.4.Installation and Operational Troubleshooting........................................................... 43
4.4.1.Electrical Fault Finding Chart............................................................................. 45
4.5.Fan Box Assembly Schematic.................................................................................. 46
4.6.Wiring in Fan Box Schematic ................................................................................... 46
4.7.Circuit Diagram......................................................................................................... 47
4.8.Wiring inside Control Box ......................................................................................... 47

Page 1
1. GENERAL INFORMATION
Introduction
1. This appliance is suitable for installation in GB and IE and should be installed in
accordance with the rules in force.
In GB, the installation must be carried out by a Gas Safe Registered Installer registered for
working on this type of appliance. It must be carried out in accordance with the relevant
requirements of the:
•Gas Safety (Installation and Use) Regulations.
•The appropriate Building Regulations either The Building Regulations, The
Building Regulations (Scotland), Building Regulations (Northern Ireland).
•The Current I.E.E. Wiring Regulations.
Where no specific instructions are given, reference should be made to the relevant British
Standard Code of Practice (see item 2).
In IE, the installation must be carried out by a Competent Person and installed in
accordance with the current edition of I.S.813 “Domestic Gas Installations”, the current
Building Regulations and reference should be made to the current ETCI rules for electrical
installation.
On completion of an installation in IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance to I.S.813.
2. The installation of the fire in GB should follow the recommendations of the following
current British Standards:
BS 5871: Pt 2 Installation of ILFE Gas Fires
BS 6891 Pipe work Installation
BS 5440: Pts 1 & 2 Flues and Ventilation
IGE/UP/7 IGE document for gas installations in Timber Frame Buildings
(Available from CORGI or Institute of Gas Engineers)
3. In other EC countries equivalent rules in force must be used.
4. It is important for correct combustion of this fire that the imitation fuel is placed in
accordance with the instructions given in this and associated booklets. Only approved
imitation fuel, available from Burley Magiglo., should be used with this appliance.
5. It is recommended that a fire guard complying with BS 8423 be fitted for the protection of
young children, the elderly or infirm.
6. This fire is intended for decorative purposes only.
7. The user is warned not to throw any rubbish onto the fire or to disturb the fuel bed.
8. The user is advised that the ceramics used within this appliance require extra care whilst
cleaning. Please refer to the Cleaning Instructions.
9. It is important for the fire to be serviced regularly. An annual service is recommended.
Ventilation Requirements
1. For models with heat inputs not exceeding 6.9kW, normal adventitious ventilation is
usually sufficient to satisfy the ventilation requirements of these appliances. In GB
reference should be made to BS 5871 Part 2, and in IE reference should be made to the

Page 2
current edition of I.S.813 which makes clear the conditions that must be met to
demonstrate that sufficient ventilation is available.
2. If provided, any purpose provided ventilation must be checked periodically to ensure it is
free from obstructions.
3. When fitting the fire in Northern Ireland (NI), purpose provided ventilation must be
provided in accordance with the rules in force.
4. In other EC countries equivalent rules in force must be used.
Flue Requirements
This product is supplied as a complete system, including all necessary flue components.
Gas Supply
1. This range of decorative gas fires are suitable for use with either Natural Gas (G20) at
20mbar supply pressure, or LPG (G31) at 37mbar supply pressure (please check
appliance data plate for compatibility).
2. A separate means of isolating the gas supply should be provided near to the appliance to
facilitate servicing. For this, an isolation valve has been supplied with the appliance.
Electrical Supply
Connection can be made using one of the following methods:
a) A fused spur providing 230v 50Hz AC, protected with 3A fuse, located adjacent to the
appliance.
b) A BS1363/A approved (three pin) plug with a 3 Amp rated fuse, can be fitted to the
power supply cable on the appliance and plugging into a suitable wall socket nearby.
The wires in the mains power supply lead on the appliance must be connected to the
plug in accordance with the diagram below.
Connect BLUE
to N(neutral)
Outer Sleeve
firmly clamped
Cable grip
Connect BROWN
to L (live)
3Amp fuse approved
to BS1362
Connect GREEN/YELLOW
to E or (earth)
Figure 1
In case the appliance needs to be isolated from the power supply (e.g. during
servicing) switch off at the wall socket and REMOVE THE PLUG from the socket.
The electrical Installation must be carried out in accordance with The Current I.E.E.
Wiring Regulations.

Page 3
1.1. Important Note About ODS Pilot
This fire is fitted with an ODS pilot which causes the appliance to shut down in the event of a
reduction of oxygen (e.g. caused by poor ventilation) in the room. Should this happen, follow
the lighting instructions to re-light the fire. In the event that the fire should shut down again,
do NOT attempt to re-light it but contact your gas installer for remedial action to be taken.
Under no circumstances should it be adjusted or put out of action by the installer
or the user. In case the pilot needs replacing, only the approved part (available
from your supplier or Burley Magiglo.) should be fitted. Note: if any part of the
pilot assembly becomes faulty the complete assembly will need replacing.

Page 4
1.2. Fire Fret Dimensions
All models can be used with the Burley Magiglo range of frets or any other fire fret that
falls within the dimensions shown below
The fireplace opening must be suitable in size to accommodate the fire being
installed. If the appliance is to be used with other fireplace components, the
installation must allow a minimum of 5 square inches of free air space below the
base of the fire.
Minimum opening
(free air) in fire fret
Minimum opening
(free air) in ash pan cover
Figure 2
Fire Front Specification
Height to Centre (A) Maximum 9 Inches (23cm)
Minimum 7.5 Inches (19cm)
Ash Pan Cover Height (B) Maximum 3.5 Inches (9cm)
Minimum 2.5 Inches (6.4cm)
Ash Pan Cover Free Air Opening Minimum 5 sq. Inches (32.3cm2)
Fire Fret Free Air Opening Minimum 15% of total fire front
area above the base of
the fire
Ash Pan Cover Length (C) Maximum 13.5 Inches (34cm)
Minimum 12.5 Inches (32cm)

Page 5
2. USER INSTRUCTIONS
2.1. Lighting the Pilot
1. Ensure that the Fan switch (Figure 3) is
in the OFF position then switch on the
mains electrical supply to the appliance.
2. Switch the fan ON – you should hear the
fan start and a few seconds later, the
green neon will illuminate. This neon is
located below the fire.
3. Ensure that the arrow on the control
knob is pointing towards the OFF
position as shown in Figure 4. Press in
the knob and slowly turn anti-clockwise
until a click is heard. The spark should
now light the pilot. On first lighting, it
may require several attempts to allow the
pilot light to be purged of air.
4. The pilot can be viewed at the front
centre of the fire.
5. Once the pilot flame is established, hold
the control knob in for approximately 10-
20 seconds and release. The pilot
should now remain alight. Repeat the
procedure if necessary.
6. The arrow should now be pointing to the
PILOT position as shown in Figure 5.
7. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionall
y
.
IO
Fan Switch
OnOff
Gas on
indication
Figure 3 - Duo Power Fan Control (Standard)
Figure 4 - Off Position
Figure 5 - Ignition Position

Page 6
2.2. Lighting the Main Burner
1. Once the pilot is established, the main
burner can be operated by turning the
control knob anti-clockwise. The preset
minimum is found with the arrow in the
9 o’clock position as shown in Figure 6.
2. The preset maximum (as shown in
Figure 7 is found by turning the control
knob fully anti-clockwise. The control is
infinitely variable between the two preset
limits.
3. To extinguish the main burner, push the
control knob in and turn clockwise until
the arrow is in the PILOT position, then
release.
4. To extinguish the pilot, push the control
knob in and turn it clockwise until the
arrow is in the OFF position, then
release.
NOTE: The main burner will not
light unless the fan is switched
on.
Figure 6 - Minimum Position
Figure 7 - Maximum Position
WARNING: Always turn on/off
the main burner using the
control valve and NOT by
means of any power supply
switches.
2.3. Turning the Fan Off
Once the main burner has been
extinguished, the fan can be switched off.
NOTE: If the fire has been
operating for a long period, it
may prove desirable to leave
the fan operating for 5 minutes
after turning the burner off.

Page 7
2.4. Fuel Effect Layout
You fire has been supplied with either Coal or Pebble effect. Please refer to the relevant
section for instructions on how to arrange the imitation fuels.
Fuel Effect Tray Type Refer to
Coal Effect Natural Gas & LPG Section 2.4.1
Pebble Effect Natural Gas & LPG Section 2.4.2
It is recommended that the imitation fuel be left alone once the desired flame pattern has been
achieved. Constant moving of the imitation fuel will cause the fuel to disintegrate
and/or cause discolouration.
RCF Advice:
This product may use Components (Coals, Pebbles & Ceramic backs)
containing Refractory Ceramic Fibres (RCF), which are man-made vitreous
silicate fibres. Excessive exposure to this material may cause irritation to eyes,
skin and respiratory tract.
Therefore during installation and servicing we recommend that you use a HEPA
filtered vacuum to remove any dust and soot accumulated in and around the fire
before and after working on the fire, to ensure that the release of fibres from
these RCF articles is kept to a minimum.
We recommend that you should follow the normal hygiene rules of not smoking,
eating or drinking in the work area.
When replacing Components containing Refractory Ceramic Fibres (RCF), we
recommend that the replaced items are not broken up, but are sealed within
heavy duty polythene bags, and clearly labelled as RCF waste. RCF waste may
be disposed of in suitably licensed landfill sites.
WARNING: Do not touch the fire when it is alight. The fire will remain very hot for
a while after extinguishing.
Some sooting on the pebbles may be observed. This is perfectly normal.
Periodically operating the Fire at various rates will burn this soot away. If
excessive sooting is observed, this is an indication that the pebbles are laid
incorrectly – please refer to instructions.

Page 8
2.4.1. Coal Effect Layout
This fire is supplied with different sizes of
ceramic coal as follows:
Qty
Small Square Coals 8
Medium Square Coals 4
Random Coals 8
Small Random Coals 9
Aeration Tubes 2
½ Aeration Tubes 1
Proceed with the coal layout as follows: -
1. Following the appropriate set of
drawings, form the first layer, using the
Small square and Medium square
coals, placing the aeration tubes as
shown.
2. Unpack the Random and small
Random coals and form the second
layer, ensuring that none of these coals
come into contact with the burner board.
3. Using more of the small random coals,
form the final layer.
4. Packing the coals too tightly together will
result in a poor flame picture. The best
results come from a ‘loose’ fuel build.
5. Do not place any coals immediately over
the pilot assembly.
6. After the appliance has been allowed to
warm up, small adjustments (using a
small pair of tongs) may be made to the
top layer to achieve the desired flame
picture.
7. It is recommended that the coals be left
alone once the desired flame picture has
been achieved. Constant moving of the
coals causes the coals to disintegrate
and/or cause discolouration.
WARNING: Do not touch the
fire when it is alight. The fire will
remain very hot for a while after
extinguishing.
Medium Squa re Coals
equally spaced
Aeration
Tubes
Small Square Coals
equally spaced Cross lighting slot Pilot
Gas outlet
ports
Figure 8
4 Random coals
6 Small Random coals
Gaps
Gaps
Figure 9
3 Small Random coals
4 Random Coals
Figure 10

Page 9
2.4.2. Pebble Effect Layout
The fire is supplied with ceramic pebble sets
as follows:-
Qty
Large Pebbles (A, B & K) 9
Medium Pebbles (C & D) 6
Small Pebbles (G) 3
Flat Pebbles (H) 4
Front Pebbles (E & J) 6
Aeration Tubes 2
½ Aeration Tubes 1
NOTE: When placing pebbles on the tray
ensure the lettering on them is facing down
and into the fire. After every step of pebble
laying ensure that they are stable.
Proceed with the pebble layout as follows:-
1. Unpack the aeration tubes, pebbles H,
E & J and place them on the tray as
shown in Figure 11 ensuring that the
port holes and the cross ignition slot
remain clear. Note that the aeration
tubes should be placed on their back,
with the legs facing up ensuring that
none of the port holes are blocked.
2. Place pebbles C & D in position as
shown in Figure 12.
3. Place pebbles A, B, C & in position as
shown in Figure 13.
4. Place pebbles A, G & K in Figure 14
and Figure 15 to complete the fuel effect
layout.
5. Small adjustments to the top layer may
be made to alter the flame pattern if
desired flame after the fire has been
turned on. A small pair of tongs should
be used for this.
6. It is recommended that the pebbles be
left alone once the desired flame pattern
has been achieved. Constant
movement of the pebbles causes the
pebbles to disintegrate and/or cause
discolouration.
WARNING: Do not touch the
fire when it is alight. The fire
will remain very hot for a while
after extinguishing.
Figure 11
HHH
CDC
Figure 12
HHH
B
B
A
A
A
D
B
D
C
Figure 13
HHH
KK
A
Figure 14
HHH
GG
G
Figure 15

Page 10
2.5. Fitting Standard Trim (if supplied)
1. Most trims are coated with a protective
film. This must be removed by peeling
off before fitting the trim.
2. The trim is held on by four magnets.
These will either be attached to the trim
or supplied loose in a separate envelope.
Space them as shown in Figure 16.
3. Offer the trim onto the flange of the
firebox. The magnets will hold the trim in
position.
4. Centralise the trim as necessary.
Magnets
Figure 16
2.6. Fitting ioss Fascia (if supplied)
1. The Fascia is coated with a protective
film. This must be removed by peeling
off before fitting the fascia.
2. The fascia is held on by four magnets.
These will either be attached to the trim
or supplied loose in a separate envelope.
Position them as shown in Figure 17.
3. Offer the fascia onto the flange of the
firebox. The magnets will hold the fascia
in position.
4. Centralise the trim as necessary.
5. The removable cover can be lifted off to
access the controls.
MAGNETS
Removable
cover to access
controls
MAGNETS
Figure 17

Page 11
2.7. Home Improvements
WARNING: If after installation of this fire any home improvements (e.g. double
glazing, secondary double glazing, draught proofing, fitting extractor fans,
laminate flooring etc.) are carried out to the property it is essential to carry out a
spillage test on the fire to ensure that the flue is still operating satisfactorily.
NOTICE: Discolouration of wall surfaces
Generally, heating appliances will create warm air convection currents that will
transfer heat to any wall surface against which they are located.
Some soft furnishings (including blown vinyl wallpapers) may not be suitable for
use where they are likely to encounter temperatures above the normal room
level. For this reason, the manufacturer’s advice should be sought before using
this type of wall covering adjacent to any heating appliance.
The likelihood of wall staining caused from convected air currents will be
increased in areas where high levels of tobacco smoke or other contaminants
exist.

Page 12
2.8. Cleaning and Care Instructions
CAUTION: Ensure that the appliance is off (including the pilot light) and has
completely cooled (off for at least 2 hours) before carrying out any cleaning or
maintenance.
RCF Advice:
This product may use Components (Coals, Pebbles & Ceramic backs)
containing Refractory Ceramic Fibres (RCF), which are man-made vitreous
silicate fibres. Excessive exposure to this material may cause irritation to eyes,
skin and respiratory tract.
Therefore during installation and servicing we recommend that you use a HEPA
filtered vacuum to remove any dust and soot accumulated in and around the fire
before and after working on the fire, to ensure that the release of fibres from
these RCF articles is kept to a minimum.
We recommend that you should follow the normal hygiene rules of not smoking,
eating or drinking in the work area.
When replacing Components containing Refractory Ceramic Fibres (RCF), we
recommend that the replaced items are not broken up, but are sealed within
heavy duty polythene bags, and clearly labelled as RCF waste. RCF waste may
be disposed of in suitably licensed landfill sites.
2.8.1. Cleaning the Fire-Bed and the Imitation Coals/Pebbles
1. If excessive debris is observed on the
imitation fuels or fire-bed, this must be
removed before further using the fire.
2. Carefully remove all the imitation fuel
from the fire-bed. Any soot or debris on
the fuel can be gently brushed away with
a soft brush - DO NOT use a vacuum
cleaner.
3. Use a low powered HEPA filtered
vacuum cleaner with a small nozzle to
clean the burner board by gently
sweeping the nozzle above the surface
of the board. Clean the ports (small
holes on the board) in a similar fashion.
4. Relay the imitation fuel after cleaning, in
accordance with the layout instructions in
this booklet.
5. When satisfactory flame appearance has
been achieved after positioning the
coals, they should not be moved
unnecessarily. Constant moving of the
imitation fuels will damage and/or
cause discolouration.

Page 13
2.8.2. Cleaning the Pilot
The oxygen depletion sensing pilot fitted to
your Burley Magiglo fire is a highly reliable
safety device which causes the fire to shut
down in the unlikely event of a reduction of
oxygen in the room where the fire is fitted.
After a period of time, it is possible for lint
(carpet fluff, pet hair, dust, etc.) to build up
on the lint guard assembly (see diagram)
causing some of the following symptoms:
1. The pilot does not light readily.
2. Yellow flame on pilot burner.
3. Fire shuts down unexpectedly.
4. The pilot does not stay alight after
releasing the control lever.
If any of the above symptoms show, follow
the instructions below for removing the
offending blockage:
1. Using a pair of tweezers (if available) or
a piece of fine soft wire, pick out the lint
from the lint guard.
2. With the aid of a small nozzle attachment
on your vacuum cleaner, apply suction at
the lint guard on the pilot. Very carefully,
do the same on the pilot head.
If, after carrying out the above procedure,
there is no improvement to the performance
of the fire, seek expert help.
Lint Guard
Figure 18
2.8.3. Cleaning the Fire Back
You should not attempt to clean the fireback,
as it is made of soft ceramic fibre, which is
easily damaged. However, if it should be
required, a light dusting with a very soft
brush will remove any soot or dust marks.
NOTE: Any attempt to clean the
fire back using an alternative
method, will result in irreparable
damage leading to a
replacement back being
required.
2.8.4. Painted Metal Surfaces
These surfaces should be dusted regularly
and any marks removed with a soft damp
cloth.

Page 14
2.8.5. Brass or Chrome Surfaces
These surfaces should be cleaned with a proprietary non-abrasive metal cleaner.
Remove the trim (if fitted), the fret and the ash-pan cover before cleaning.
The trim is held in place by means of four magnets at the rear of the trim. The fret and the
ash-pan cover are free standing in front of the fire.
2.8.6. Stainless Steel
Stainless steels need to be cleaned for aesthetic considerations and to preserve corrosion
resistance.
Oil and finger marks can be removed using a glass cleaner or preferably a mild solution of
warm water and detergent.
Scratches can be removed by gently rubbing in the direction of the grain with a 240 grit emery
cloth (or similar). Once the scratch has been completely removed the surface can then be re-
polished using 3M Scotchbrite pads - Fine Grade.
Periodically it may be necessary to coat the entire surface in order to achieve a uniform finish.
This can be achieved by applying a light coat of oil (baby oil) using a soft lint free cloth, then
buffing in line with the grain until the excess is removed.
NOTE: After any cleaning process the surface must be thoroughly dried.
2.8.7. Care of Ceramic Backs
The ceramic fireback on this appliance must NOT be sprayed with any type of solvent-based
high temperature paint.
The very high temperatures produced within the appliance will cause the paint to bubble
and/or burn off rendering the fireback looking unsightly.
Minor surface scuffs may be treated using a water based touch up stain available at Burley
Magiglo fire retailers.
Extreme care should be taken when handling and installing products containing
ceramic interiors, so as not to cause damage.

Page 15
3. INSTALLATION INSTRUCTIONS
Before installation, ensure that the local distribution conditions (identification of the
type of gas and pressure) and the adjustment of the appliance are compatible
3.1. General Safety Requirements
Before commencing installation, ensure that the intended installation will comply
with details in General Information on Page 1.
3.2. General Dimensions
3.2.1. Dimensions for Standard Duo Power (excluding Freedom
Surround)
E
A
B
C
D
Figure 19 – Standard Box Dimensions
(refer to Table 1)
Side Vent Trim
Switch
A
580mm 580mm
B 575mm 575mm
C 400mm 400mm
D180mm 155mm
E 486mm 486mm
Table 1

Page 16
3.2.2. Additional Dimensions for Duo Power with Freedom Surround
FLUE
A
DAPTER
675mm
700mm
545mm
570mm
180mm
Figure 20