Magiglo AFFINITY PLUS 20" User guide

Users,
Installation & Servicing
Instructions
MUST BE LEFT WITH THE USER
AFFINITY PLUS 16” &
ALLUSION PLUS 16”
Fuel Effect Options:
Coal Effect
Pebble Effect
Beachcomber Effect
Shoreline Effect
All available on NG & LPG
Control Options:
Upgradeable Manual Control
Remote Control (Response-S)
Optimum Control
Trim Switch Control
Total Control
For use on Natural Gas (G20) at a supply pressure of 20mbar
or Propane (G31) at a supply pressure of 37mbar in GB and IE
(Dependent upon model)

Manufacturer Contact Details:
Burley Appliances Ltd
Lands End Way
Oakham, Rutland, LE15 6RB
Tel: [phone]
Fax: [phone]
General E-Mail: [e-mail]
Web Site: www.magiglo.co.uk
Technical Support: Direct Dial on [phone] or email: [e-mail]
Magiglo Document Number:
MF446.31 CAS
Revision Date:
22 October 2009
Copyright:
This documentation is copyrighted by Burley Appliances Ltd. ©2009.
No part of this document may be copied, photocopied or reproduced in any form or by any
means without permission in writing from Burley Appliances Ltd.
Magiglo is a registered trademark of Burley Appliances Ltd.
Service Warranty:
In the unlikely event of a defect in materials or workmanship occurring within one year of
purchase, Burley Magiglo will arrange to repair or replace the item free of charge.
Any claims under this warranty must be made through the retailer from whom the product
was purchased.
As the purchaser’s contract of sale is with the retailer, Burley Magiglo are unable to enter
into discussions with the purchaser until the retailer has inspected any claim and deemed
it to be valid.
Burley Magiglo reserve the right to refuse service or make a charge for any service call,
when a defect is due to installation error or misuse.
Extended warranty (if purchased) commences after the first year; please see separate
registration for further information.
Appliance Details:
For future reference, please complete the following information at the time of installation.
Model and Serial Number details may be found on the data plate as shown.
Serial Number
Model
Installation Date
Installed By
Model
Serial
Number

Page i
Contents
1.GENERAL INFORMATION ........................................................................................................ 1
1.1.Important Note About ODS Pilot ................................................................................ 2
2.USER INSTRUCTIONS ............................................................................................................. 3
2.1.Lighting Procedure ..................................................................................................... 3
2.1.1.Lighting Procedure (Upgradeable Manual Control) ............................................. 4
2.1.2.Lighting Procedure (Remote Control) .................................................................. 5
2.1.3.Lighting Procedure (Optimum Control and Trim Switch Control)......................... 6
2.1.4.Lighting Procedure (Total Control)....................................................................... 7
2.1.5.Manual Operation (Total Control Model) ............................................................. 8
2.2.Battery Replacement (Remote Control & Total Control) ............................................ 9
2.2.1.Handset................................................................................................................ 9
2.2.2.Receiver Unit ....................................................................................................... 9
2.3.Battery Replacement (Optimum Control) ................................................................. 10
2.4.Battery Replacement (Trim Switch Control)............................................................. 10
2.5.Fuel Effect Layout .................................................................................................... 11
2.5.1.Coal Effect Layout.............................................................................................. 12
2.5.2.Pebble Effect Layout.......................................................................................... 14
2.5.3.Beachcomber Effect and Shoreline Effect Layout ............................................. 16
2.6.Home Improvements ................................................................................................ 18
2.7.Cleaning and Care Instructions ................................................................................ 19
2.7.1.Cleaning the Fire-Bed with Imitation Fuel Effect................................................ 19
2.7.2.Cleaning the Pilot............................................................................................... 20
2.7.3.Cleaning the Fire Back....................................................................................... 20
2.7.4.Painted Metal Surfaces...................................................................................... 20
2.7.5.Care of Ceramic Backs ...................................................................................... 20
3.INSTALLATION INSTRUCTIONS .............................................................................................. 21
3.1.General Safety Requirements.................................................................................. 21
3.2.Flue Requirements ................................................................................................... 21
3.2.1.Masonry Flue ..................................................................................................... 21
3.2.2.Installation into a 125mm (5”) Class 2 Metal Flue system ................................. 22
3.2.3.Installation Example using Existing Builder’s Opening ...................................... 23
3.3.General Dimensions................................................................................................. 23
3.4.Technical Data ......................................................................................................... 24
3.5.Pressure Test Point Locations ................................................................................. 24
3.6.Appliance Location ................................................................................................... 25
3.6.1.Raised Fireplace Opening ................................................................................. 26
3.6.2.Physical Barrier.................................................................................................. 27
3.7.Ventilation................................................................................................................. 29
3.8.Contents Checklist ................................................................................................... 29
3.9.Installation Procedure............................................................................................... 30
3.9.1.Initial Installation of Pure Additions Fascia (if applicable).................................. 30
3.9.2.Preparing the Firebox ........................................................................................ 30
3.9.3.Preparing the Fireplace Opening (all models) ................................................... 31
3.9.4.Installing the Firebox (all models) ...................................................................... 32
3.9.5.Connecting the Gas Supply ............................................................................... 33
3.9.6.Installation of Pure/Form Fascia Pack (Affinity) ................................................. 34
3.9.7.Installation of Dimension Fascia Pack (Allusion) ............................................... 35
3.9.8.Continuation of Installation - Remote Control Model ......................................... 36
3.9.9.Continuation of Installation - Optimum Control Model ....................................... 37
3.9.10.Continuation of Installation - Trim Switch Control Model ................................... 38
3.9.11.Continuation of Installation – Total Control........................................................ 38

Page ii
3.9.12.Commissioning .................................................................................................. 39
3.9.13.Checking for Spillage ......................................................................................... 40
3.9.14.Instructing the User............................................................................................ 40
4.SERVICING INSTRUCTIONS ................................................................................................... 41
4.1.General Requirements ............................................................................................. 41
4.2.Servicing Instructions ............................................................................................... 41
4.3.Replacing Parts ........................................................................................................ 42
4.3.1.Pilot Assembly Replacement ............................................................................. 42
4.3.2.Injector Replacement ......................................................................................... 42
4.3.3.Control Valve Replacement (Mertik GV34)........................................................ 42
4.3.4.Motor Replacement (Remote/Optimum/Trim Switch Control)............................ 43
4.3.5.Replacing Mertik GV60 Valve (Total Control).................................................... 44
4.3.6.Replacing the Receiver (Total Control).............................................................. 44
4.3.7.Programming Handset to Receiver (Total Control)............................................ 44
4.3.8.Replacing the Ceramic Back and Sides ............................................................ 45
4.4.Installation and Operational Troubleshooting........................................................... 46

Page 1
1. GENERAL INFORMATION
Introduction
1. This appliance is suitable for installation in GB and IE and should be installed in
accordance with the rules in force.
In GB, the installation must be carried out by a Gas Safe Registered Installer registered for
working on this type of appliance. It must be carried out in accordance with the relevant
requirements of the:
•Gas Safety (Installation and Use) Regulations.
•The appropriate Building Regulations either The Building Regulations, The
Building Regulations (Scotland), Building Regulations (Northern Ireland).
•The Current I.E.E. Wiring Regulations.
Where no specific instructions are given, reference should be made to the relevant British
Standard Code of Practice (see item 2).
In IE, the installation must be carried out by a Competent Person and installed in
accordance with the current edition of I.S.813 “Domestic Gas Installations”, the current
Building Regulations and reference should be made to the current ETCI rules for electrical
installation.
On completion of an installation in IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance to I.S.813.
2. It is important for correct combustion of this fire that the imitation fuel is placed in
accordance with the instructions given in this booklet. Only approved imitation fuel,
available from Burley Magiglo., should be used with this appliance.
3. It is recommended that a fire guard complying with BS 8423 be fitted for the protection of
young children, the elderly or infirm.
4. The user is warned not to throw any rubbish onto the fire or to disturb the fuel bed.
5. The user is advised that the ceramics used within this appliance require extra care whilst
cleaning. Please refer to the Cleaning Instructions.
6. It is important for this fire to be serviced regularly depending on usage. An annual service
is recommended.
Efficiency Declaration
The efficiency of this appliance has been measured as specified in BS 7977: Part 1 and a
value of up to 53.5%* was achieved. The gross calorific value of the fuel has been used for
this efficiency calculation. The test data from which it has been calculated has been certified
by Advantica Ltd. The efficiency value may be used in the UK Government’s Standard
Assessment Procedure (SAP) for energy rating of dwellings (* 59.3% net efficiency).
Ventilation Requirements
1. This appliance does not normally require any ventilation in the room it is fitted in. In GB
reference should be made to BS 5871 Part 2, and in IE reference should be made to the
current edition of I.S.813 which makes clear the conditions that must be met to
demonstrate that sufficient ventilation is available.
2. If provided, any purpose provided ventilation must be checked periodically to ensure it is
free from obstructions.

Page 2
3. When fitting the fire in Northern Ireland (NI), purpose provided ventilation must be
provided in accordance with the rules in force.
4. In other EC countries equivalent rules in force must be used.
Flue Requirements
Class 1 Masonry Flue - A flue having no cross sectional dimension less than 175mm (7”)
e.g. 225mm (9”) by 225mm (9”) Masonry chimney or 175mm (7”) diameter clay liner.
Class 1 Masonry Flue with liner – A masonry flue having a flexible metal flue liner with a
cross sectional dimension no less than 125mm.
Class 2 – A metal flue having no cross sectional dimension less than 125mm (5”).
Please refer to the full Flue and Chimney Requirements within the Installation Instruction
section. The chimney must be checked regularly to ensure that all the products of
combustion are entering the flue and there is no excessive build up of soot.
Gas Supply
1. This gas fire is suitable for use with either Natural Gas (G20) at 20mbar supply pressure
or with Propane (G31) at 37mbar supply pressure.
2. Connection to the gas supply must be made using rigid or semi-rigid tubing.
3. A separate means of isolating the gas supply should be provided near to the appliance to
facilitate servicing. An isolating valve has been supplied for this purpose.
Electrical Supply
Not applicable to this range of appliances.
1.1. Important Note About ODS Pilot
This fire is fitted with an ODS pilot which causes the appliance to shut down in the event of a
reduction of oxygen (e.g. caused by poor ventilation) in the room. Should this happen, follow
the lighting instructions to re-light the fire. In the event that the fire should shut down again,
do NOT attempt to re-light it but contact your gas installer for remedial action to be taken.
Under no circumstances should it be adjusted or put out of action by the installer
or the user. In case the pilot needs replacing, only the approved part (available
from your supplier or Burley Magiglo.) should be fitted. Note: if any part of the
pilot assembly becomes faulty the complete assembly will need replacing.

Page 3
2. USER INSTRUCTIONS
2.1. Lighting Procedure
Your fire will be fitted with one of the five different types of gas control. Identify the control
system on your fire as shown and follow the appropriate operating instructions in the
appropriate section.
Control Valve Operation Control Type
+
Manual =
Upgradable
Manual
Control
See
Section 2.1.1
on Page 4
+
=
Remote
Control
See
Section 2.1.2
on Page 5
+
=
Optimum
Control
See
Section 2.1.3
on Page 6
+=
Trim Switch
Control
See
Section 2.1.3
on Page 6
+
=
Total
Control
See
Sections
2.1.4 & 2.1.5
on Pages
7 & 8

Page 4
2.1.1. Lighting Procedure (Upgradeable Manual Control)
1. Whilst pushing the IGNITION KNOB in
(see Figure 1), turn it anticlockwise to
the pilot flame position as shown in
Figure 2. During this process, the spark
ignition will have operated and lit the pilot
flame. On lighting the pilot flame
continue to depress the ignition knob for
a further 10 - 12 seconds then slowly
release. The pilot flame should stay
alight. If the flame goes out repeat the
procedure above to establish the pilot.
2. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
3. Turn the IGNITION KNOB anticlockwise
to the main flame position as shown in
Figure 3.
4. Turn the GAS RATE ADJUSTING KNOB
fully anticlockwise (until you reach the
stop position) i.e. the maximum gas rate.
See Figure 4.
5. The main burner will have cross-lit from
the pilot.
6. Now the gas rate can be adjusted to the
desired setting by turning the GAS RATE
ADJUSTING KNOB to any position
between the pre-set high and low.
7. To switch off the main burner turn the
IGNITION KNOB to the ‘Pilot burner only
Position’ as shown in Figure 2. The
appliance may be left in this standby
mode if desired.
8. To turn the pilot off turn the Ignition Knob
on the control valve fully clockwise to ‘¦’
position.
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.
Ignition knob
Gas rate adjusting knob
Figure 1 - Off Position
Figure 2 – Pilot burner only
Figure 3 – Main burner operational, but gas flow off
Figure 4 - Main Burner operational & Maximum Gas
Rate

Page 5
2.1.2. Lighting Procedure (Remote Control)
1. Press the bottom button on the remote
handset until clicking is heard on the
valve, and the gas rate adjustment knob
is at the off position.
2. With gas available at the valve press the
IGNITION KNOB in and turn it
anticlockwise to the pilot flame position.
A click of the piezo igniter will be heard
and a spark will appear at the electrode.
At the same time the gas will flow to the
pilot burner and should be ignited by the
spark. Repeat the procedure until the
pilot flame is established.
3. Keep the knob pressed in for a further 10
- 12 seconds and slowly release it. The
pilot flame should stay alight. If the
flame goes out repeat the procedure
above to establish the pilot.
4. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
5. Turn the IGNITION KNOB
anticlockwise to the Main Burner
Operation position as shown in Figure
5.
6. Using the HANDSET (as shown in
Figure 6) press and hold both the top
and the small button together until the
main burner goes to full rate and clicking
can be heard from the valve. During this
process the main burner will ignite from
the pilot.
7. By pressing the two buttons together (to
increase the gas rate) and the lower
button only (to decrease the gas rate)
the valve can be manipulated to select
the desired gas rate between maximum
and minimum. By pressing the buttons
in short bursts you will be able to adjust
the gas rate in small steps.
8. To turn the fire off, continuously press
the lower button until the flame dies
down and clicks can be heard from the
valve. Release the button as soon as
the clicks are heard.
9. The fire can safely be left in this position
at all times, however to prevent
unauthorised or accidental use (say by
children) it is recommended to turn the
IGNITION KNOB to the pilot flame
position by turning it 90 degrees
clockwise. To turn the pilot off, turn the
IGNITION KNOB fully clockwise.
NOTE: The clicking sound
made by the valve is the
operation of the valve clutch,
and indicates either maximum
or off position.
IGNITION
KNOB
FULL RATE
POSITION
MAIN BURNER
OFF POSITION
PILOT ONLY
POSITION
MAIN BURNER
OPERATION
GAS RATE
ADJUSTMENT
KNOB
Figure 5 – Gas Valve
Press these
two buttons
together to
increase
gas rate
Press this
button to
decrease
gas rate
Figure 6 - Handset Operation
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.

Page 6
2.1.3. Lighting Procedure (Optimum Control and Trim Switch Control)
1. Ensure the main burner is off by pressing
the button on the trim marked
(‘small flame/dot’) until clicking is heard
on the valve (see Figure 7/Figure 8).
2. With the gas available at the valve press
in the IGNITION KNOB and turn it
anticlockwise to the pilot flame position
(see Figure 9). A click of the piezo
igniter will be heard and a spark will
appear at the electrode. At the same
time the gas will flow to the pilot burner
and will be ignited by the spark. Repeat
the procedure until the pilot flame is
established.
3. Keep the knob pressed in for a further 10
- 12 seconds and slowly release. The
pilot flame should stay alight. If the flame
goes out repeat procedure above to
establish the pilot.
4. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
5. Turn the IGNITION KNOB anticlockwise
to the main flame position.
6. Press and hold the (‘large flame’)
button (in Figure 7/Figure 8) until
clicking is heard (fully open).
7. The main burner will have cross-lit from
the pilot.
8. Now the gas rate can be adjusted to the
desired setting by pressing the
(‘small flame/dot’) button. Any rate
between the pre-set high and low can be
obtained using the two buttons.
9. To switch off the main burner press and
hold the (‘small flame/dot’) button
until clicking is heard from the valve
(OFF position).
10. The fire can safely be left in this position
at all times, however to prevent
unauthorised or accidental use (say by
children) it is recommended to turn the
IGNITION KNOB to the pilot flame
position by turning it 90 degrees
clockwise. To turn the pilot off, turn the
IGNITION KNOB fully clockwise.
NOTE: The clicking sound
made by the valve is the
operation of the valve clutch,
and indicates either maximum
or off position.
Figure 7 – Trim Switch
Figure 8 - Wall Switch
IGNITION
KNOB
GAS RATE
ADJUSTING
KNOB
GAS VALVE
Figure 9
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.
High
Low/Off

Page 7
2.1.4. Lighting Procedure (Total Control)
1. Ensure that gas is available at the valve
and the ON/OFF switch in the ON
position (–).
2. Simultaneously press and hold the
(red circle) and (large flame)
buttons until a short acoustic signal
confirms the start sequence has begun,
then release the buttons (see Figure
10).
3. Continuing signals confirm the ignition is
in process. Once the pilot is lit the gas
rate adjusting knob automatically
turns to high gas rate. The main
burner cross-lights from the pilot.
4. To adjust the gas rate to desired setting
press the (large flame) to increase the
flame height or (small flame) to
decrease the flame height on the
handset (see Figure 11).
5. For fine adjustment tap the or
buttons.
6. To leave the burner in the standby
mode press the (small flame) until the
main burner goes out. In the standby
mode the pilot stays alight.
7. To turn off the main burner and the pilot
press the ‘OFF’ button on the hand set.
WARNING: Ensure that the
fire is operated only whilst
present in the room where it
is fitted either intentionally
or unintentionally.
Manual
Knob
Gas Rate
Adjusting
Kno
b
ON/OFF Switch
NO
MAN
ON
OFF
Figure 10 – Total Control Gas Valve
Press
these two
buttons
together to
light the
burner
Once lit
use this
button to
increase
gas rate
Once lit
use this
button to
decrease
gas rate
Figure 11 – Total Control Handset

Page 8
2.1.5. Manual Operation (Total Control Model)
In emergency the appliance can be operated
manually as follows:
1. Turn the Gas Rate Adjusting knob fully
clockwise to the OFF position. A
clicking sound will be audible, but this is
perfectly alright.
2. Turn the Manual knob clockwise to
MAN position (see Figure 12).
3. Ensure that the ON/OFF switch is in the
ON (–) position.
4. Using a rigid slender object (like a
screwdriver) depress the pilot valve
operator through the large hole in the
knob (see Figure 13) and light the pilot
using a match or lighted taper.
5. Keep the valve operator depressed for
a further 10 seconds and slowly
release. The pilot should stay alight.
Repeat step 4 if necessary.
6. Turn Manual knob anticlockwise to ON
position.
7. Turn the Gas Rate adjusting knob
anticlockwise to ON position to turn the
main burner on. Adjust this knob to get
the desired gas rate between maximum
and minimum.
8. To turn the main burner off but, leaving
the pilot on, turn the Gas Rate adjusting
knob fully clockwise past the OFF
position.
9. To turn the pilot off place the ON/OFF
switch to OFF (O) position.
MAN
NO
ON/OFF Switch
Manual
Knob
Gas Rate
Adjusting
Knob
ON
OFF
Figure 12
MAN
NO
Gas Rate
Adjusting
Knob
O
N
OFF
Figure 13
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.

Page 9
2.2. Battery Replacement (Remote Control & Total
Control)
2.2.1. Handset
1. On the reverse of the handset remove
the battery cover by pressing down at
the top of the cover and sliding down.
2. Remove and unclip the old battery and
replace with a new PP3 9V battery.
3. Replace the cover.
Press here and
slide down
Figure 14
2.2.2. Receiver Unit
1. Remove the receiver unit from under the
fire burner (or from wherever positioned
if mounted remotely) and remove the
battery compartment cover (see Figure
15).
2. Replace the old batteries with new ones,
ensuring they are inserted in the correct
polarity.
3. Replace the cover on the receiver unit,
ensuring that it is securely closed.
4. Return the receiver unit to its original
mounting position.
Figure 15 – Receiver for Remote Control Option
CAUTION: With the exception of battery replacement, the battery holder must be
located within the heat shield at all times.

Page 10
2.3. Battery Replacement (Optimum Control)
1. The battery pack is mounted inside the
wall-mounting box behind the wall switch
plate.
2. To change the batteries remove the two
small screws securing the wall plate
using a small screwdriver.
3. Remove the battery pack from the wall
box and replace the spent batteries with
new ones (4 off 1.5V AA batteries)
ensuring correct polarity.
4. Insert the battery pack back into the wall
box and refit the wall plate ensuring that
it is the right way up.
5. Secure with screws.
REAR OF WALL
PLATE
CABLE TO
VALVE
BATTERY
PACK
(4 x 1.5 V AA
BATTERIES)
LOW/OFF
SWITCH
HIGH
SWITCH
brown brown
brown
blue
blue
blue
white
black
Figure 16
2.4. Battery Replacement (Trim Switch Control)
1. Open the fascia door.
2. Slide out the battery holder from under
the fire.
3. Replace all batteries with new ones (4 x
AA batteries required). Ensure that the
batteries are inserted with correct
polarity in the holder.
4. Replace the battery holder into the
compartment under the heat shield.
5. Close the fascia door.
Heat
Shield
Battery
Holder
Bur ner Tray
Tray
Fixing
Screw
Tr ay
Fixing
Screw
Figure 17
CAUTION: With the exception of battery replacement, the battery holder must be
located within the heat shield at all times.

Page 11
2.5. Fuel Effect Layout
You fire has been supplied with Coal, Pebble, Beachcomber or Shoreline effect fuel bed.
Please refer to the relevant section for instructions on how to arrange the imitation fuels.
It is recommended that the imitation fuel be left alone once the desired flame pattern has been
achieved. Constant moving of the imitation fuel will cause the fuel to disintegrate and/or
cause discolouration.
RCF Advice:
This product may use Components (Coals, Pebbles, Driftwood & Ceramic backs)
containing Refractory Ceramic Fibres (RCF), which are man-made vitreous
silicate fibres. Excessive exposure to this material may cause irritation to eyes,
skin and respiratory tract.
Therefore during installation and servicing we recommend that you use a HEPA
filtered vacuum to remove any dust and soot accumulated in and around the fire
before and after working on the fire, to ensure that the release of fibres from
these RCF articles is kept to a minimum.
We recommend that you should follow the normal hygiene rules of not smoking,
eating or drinking in the work area.
When replacing Components containing Refractory Ceramic Fibres (RCF), we
recommend that the replaced items are not broken up, but are sealed within
heavy duty polythene bags, and clearly labelled as RCF waste. RCF waste may
be disposed of in suitably licensed landfill sites.
WARNING: Do not touch the fire when it is alight. The fire will remain very hot
for a while after extinguishing.
Some sooting on the fuel bed may be observed. This is perfectly normal.
Periodically operating the fire at various rates will burn this soot away. If
excessive sooting is observed, this is an indication that the fuel bed is laid
incorrectly – please refer to instructions.

Page 12
2.5.1. Coal Effect Layout
This fire is supplied with different sizes of
ceramic coal :
Qty
Small Square Coals 5
Medium Square Coals 1
Random Coals 18
Small random coals 5
Matrices 2
Proceed with the coal layout as follows: -
1. Having unpacked all the fuel-bed
components proceed with placing the
rear matrix centrally and to the rear of
the burner tray ensuring that it touches
the ceramic fire-back.
2. Place the middle matrix onto the burner
board so that it keys into the triangular
depression on the board (see Figure
18).
3. Insert the front fuel spike between the
board and the front of the metal tray (see
Figure 18).
4. Unpack the square coals and insert them
into the spikes as shown in Figure 19.
Then place Large Random coals on the
middle matrix such that they are bridging
across to the rear matrix.
5. Continue laying the coals as shown in
Figure 20 to Figure 23 ensuring that the
coals are placed ‘loosely’. Packing the
coals too tightly together will result in a
poor flame picture. The best results
come from a ‘loose’ fuel build.
6. After the appliance has been allowed to
warm up, small adjustments (using a
small pair of tongs) may be made to the
top layer to achieve the desired flame
picture.
7. It is recommended that the coals be left
alone once the desired flame picture has
been achieved. Constant moving of
the coals causes the coals to
disintegrate and/or cause
discolouration.
Rear matri
x
Middle Ma tr i x
FrontFuel Spikes
Burner Board
Figure 18
Medium
Square
Coal
Small
Square
Coals
Random
Coals
Figure 19
Random
Coals
Figure 20
Random
Coals
Figure 21
WARNING: Do not touch the
fire when it is alight. The fire
will remain very hot for a while
after extinguishing.

Page 13
Random
Coals
Figure 22
Small
Random
Coals
Figure 23

Page 14
2.5.2. Pebble Effect Layout
The fire is supplied with ceramic pebble sets
as follows:-
Qty
Large Pebbles (A, B & K) 15
Medium Pebbles (C & D) 8
Medium Pebbles (F) 2
Front Pebbles (E/J) 6
Matrices 2
NOTE: When placing pebbles on the burner
tray, ensure the lettering on them is facing
down and towards the fire. After every step
of pebble laying, ensure that they are stable.
1. Having unpacked all the fuel-bed
components proceed with placing the
rear matrix centrally and to the rear of
the burner tray ensuring that it touches
the ceramic fire-back.
2. Place the middle matrix onto the burner
board so that it keys into the triangular
depression on the board (see Figure
24).
3. Insert the front fuel spike between the
board and the front of the metal tray (see
Figure 24).
4. Insert the J & E pebbles onto the spikes
and place the A & B pebbles on the
middle matrix ensuring the same
orientation as shown in Figure 25.
5. Proceed with laying the rest of the
pebbles in accordance with Figure 26 to
Figure 29.
6. It is recommended that the pebbles be
left alone once the desired flame pattern
has been achieved. Constant moving
of the pebbles causes the pebbles to
disintegrate and/or cause
discolouration.
WARNING: Do not touch the
fire when it is alight. The fire
will remain very hot for a while
after extinguishing.
R
ear matr
i
x
Middle Matrix
Front Fuel Spi kes Burner Board
Figure 24
BA
BA B
JJ J JJE
Figure 25
KKKK
Figure 26
KK CC
B
Figure 27
ADBDK
Figure 28

Page 15
FDCF
D
C
Figure 29
Some sooting on the fuel pebbles may be observed. This is perfectly normal.
Periodically operating the Fire at various rates will burn this soot away. If
excessive sooting is observed, this is an indication that the pebbles are laid
incorrectly – please refer to instructions.

Page 16
2.5.3. Beachcomber Effect and Shoreline Effect Layout
The fire is supplied with ceramic pebble and
driftwood set as follows:
Pebbles
Qty
Large Pebbles (A, B & K) 7
Medium Pebbles (C, D & F) 5
Small Pebbles (E/J) 11
Matrices 2
Driftwood
Figure 30
NOTE: When placing pebbles and driftwood
on the burner tray, ensure that the lettering
on them is facing down and towards the fire.
After every step of pebble and driftwood
laying, ensure that they are stable.
1. Having unpacked all the fuel-bed
components proceed with placing the
rear matrix pieces centrally and to the
rear of the burner tray ensuring that it
touches the ceramic fire-back (see
Figure 31).
2. Place the middle matrix pieces onto the
burner board so that they key into the
triangular depression on the board (see
Figure 31).
3. Insert the front fuel spike between the
board and the front of the metal tray (see
Figure 31).
4. Insert the J & E pebbles centrally onto
the spikes and place the B, C& D
pebbles on the middle matrix ensuring
the same orientation as shown in Figure
32.
Rear matrix
Mi d d l e Matr i x
FrontFuel Spikes
Burner Board
Figure 31
CBBBD
JJJ
JJE
D
Figure 32
A C
G E
B
K
J