Magiglo Elite ME16T User guide

Users,
Installation & Servicing
Instructions
MUST BE LEFT WITH THE USER
ELITE
Models:
ME16T & ME18T 16” & 18” Fires
ET16 & ET18 16” & 18” Fires c/w Thermobox
EV16 & EV18 16” & 18” Victorian Fires
(LPG models prefixed with the letter L)
Fuel Effect Options:
Coal Effect – NG and LPG
Pebble Effect - NG Only
Control Options:
Manual Control
Remote Control (Response-S)
Optimum Control
Trim Switch Control
For use on Natural Gas (G20) at a supply pressure of 20mbar
or Propane (G31) at a supply pressure of 37mbar in GB and IE
(Dependent upon model)

Manufacturer Contact Details:
Burley Magiglo
Lands End Way
Oakham, Rutland, LE15 6RB
Tel: [phone]
Fax: [phone]
General E-Mail: [e-mail]
Web Site: www.magiglo.co.uk
Technical Support: Direct Dial on [phone] or email: [e-mail]
Magiglo Document Number:
BMF281.91
Revision Date:
23 September 2009
Copyright:
This documentation is copyrighted by Burley Magiglo. ©2009.
No part of this document may be copied, photocopied or reproduced in any form or by any
means without permission in writing from Burley Magiglo.
Magiglo is a registered trademark of Burley Appliances Ltd
Service Warranty:
In the unlikely event of a defect in materials or workmanship occurring within one year of
purchase, Burley Magiglo will arrange to repair or replace the item free of charge.
Any claims under this warranty must be made through the retailer from whom the product
was purchased.
As the purchaser’s contract of sale is with the retailer, Burley Magiglo are unable to enter
into discussions with the purchaser until the retailer has inspected any claim and deemed
it to be valid.
Burley Magiglo reserve the right to refuse service or make a charge for any service call,
when a defect is due to installation error or misuse.
Extended warranty (if purchased) commences after the first year; please see separate
registration for further information.
Appliance Details:
For future reference, please complete the following information at the time of installation.
Model and Serial Number details may be found on the data plate as shown.
Serial Number
Model
Installation Date
Installed By
Model
Serial
Number

Page i
Contents
1. General Information...........................................................................................................1
1.1. Important Note About ODS Pilot ................................................................................2
1.2. Fire Fret Dimensions..................................................................................................3
2. User Instructions ...............................................................................................................5
2.1. Lighting Procedure.....................................................................................................5
2.1.1. Lighting Procedure (Manual BM Control) ............................................................6
2.1.2. Lighting Procedure (Manual Mertik Control)........................................................7
2.1.3. Lighting Procedure (Remote Control)..................................................................8
2.1.4. Lighting Procedure (Optimum Control and Trim Switch Control).........................9
2.2. Battery Replacement (Remote Control)...................................................................10
2.2.1. Handset..............................................................................................................10
2.2.2. Receiver Unit .....................................................................................................10
2.3. Battery Replacement (Optimum Control).................................................................11
2.4. Battery Replacement (Trim Switch Control).............................................................11
2.5. Fuel Effect Layout ....................................................................................................12
2.5.1. Coal Effect Layout..............................................................................................14
2.5.2. Pebble Effect Layout (Natural Gas Only)...........................................................16
2.6. Fitting the Trim (Thermobox Only) ...........................................................................18
2.7. Home Improvements................................................................................................19
2.8. Cleaning and Care Instructions................................................................................20
2.8.1. Cleaning the Fire-Bed and the Imitation Coals/Pebbles....................................20
2.8.2. Cleaning the Pilot...............................................................................................21
2.8.3. Cleaning the Fire Back (Thermobox Only).........................................................21
2.8.4. Black Painted Metal Surfaces............................................................................21
2.8.5. Brass or Chrome Surfaces.................................................................................22
2.8.6. Stainless Steel...................................................................................................22
2.8.7. Care of Ceramic Backs......................................................................................22
3. Installation Instructions ..................................................................................................23
3.1. General Safety Requirements..................................................................................23
3.2. Flue Requirements...................................................................................................23
3.2.1. Masonry Flue .....................................................................................................23
3.2.2. Installation of Burley Magiglo Elite 16” Models (only) into a 125mm (5”) Class 2
Metal Flue system...........................................................................................................24
3.2.3. Installation Example using Metal Flue Box........................................................24
3.2.4. Installation Example using Existing Building Opening.......................................25
3.2.5. Installation Example using Existing Milner (Clay) Fireback ...............................25
3.3. Technical Data .........................................................................................................26
3.4. Burner Tray Layouts.................................................................................................27
3.5. Appliance Location...................................................................................................28
3.5.1. Floor Level and Raised Fireplace Openings......................................................29
3.5.2. Physical Barrier..................................................................................................30
3.6. Ventilation.................................................................................................................32
3.7. Contents Checklist ...................................................................................................32
3.8. Installation Procedure (Thermobox).........................................................................33
3.8.1. Burley Magiglo Thermobox Installation Instructions ..........................................33
3.8.2. Initial Installation (All Models) ............................................................................33
3.8.3. Installation (Deluxe Thermobox Only)................................................................33
3.8.4. Installation (Standard Thermobox Only)............................................................34
3.8.5. Installation (Slimline Thermobox Only)..............................................................34
3.8.6. Alternative Ceramic Box Installation..................................................................35

Page ii
3.9. Installation Procedure (Fire).....................................................................................36
3.9.1. Continuation of Installation - Remote Control Model .........................................36
3.9.2. Continuation of Installation - Optimum Control Model .......................................37
3.9.3. Continuation of Installation - Trim Switch Control Model...................................38
3.9.4. Installation of the Glass (Physical) Barrier (if supplied) .....................................38
3.9.5. Commissioning ..................................................................................................39
3.9.6. Checking for Spillage.........................................................................................40
3.9.7. Instructing the User............................................................................................40
4. Servicing Instructions.....................................................................................................41
4.1. General Requirements.............................................................................................41
4.2. Servicing Instructions...............................................................................................41
4.3. Replacing Parts........................................................................................................42
4.3.1. Pilot Assembly Replacement.............................................................................42
4.3.2. Injector Replacement.........................................................................................42
4.3.3. Control Valve Replacement...............................................................................42
4.3.4. Motor Replacement (Remote Control / Optimum Control Models / Trim Switch
Models)...........................................................................................................................43
4.4. Installation and Operational Troubleshooting...........................................................44

Page 1
1.GENERAL INFORMATION
Introduction
1. This appliance is suitable for installation in GB and IE and should be installed in
accordance with the rules in force.
In GB, the installation must be carried out by a CORGI Registered Installer. It must be
carried out in accordance with the relevant requirements of the:
•Gas Safety (Installation and Use) Regulations.
•The appropriate Building Regulations either The Building Regulations, The
Building Regulations (Scotland), Building Regulations (Northern Ireland).
•The Current I.E.E. Wiring Regulations.
Where no specific instructions are given, reference should be made to the relevant British
Standard Code of Practice (see item 2).
In IE, the installation must be carried out by a Competent Person and installed in
accordance with the current edition of I.S.813 “Domestic Gas Installations”, the current
Building Regulations and reference should be made to the current ETCI rules for electrical
installation.
On completion of an installation in IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance to I.S.813.
2. The installation of the fire in GB should follow the recommendations of the following
current British Standards:
BS 5871: Pt 3 Installation of Decorative Fuel Effect Gas Fires
BS 6891 Pipe work Installation
BS 5440: Pts 1 & 2 Flues and Ventilation
BS EN 1856 Chimneys - Requirements for metal chimneys - System chimney
products
BS 715 Metal flue boxes
3. In other EC countries equivalent rules in force must be used.
4. It is important for correct combustion of this fire that the imitation fuel is placed in
accordance with the instructions given in this and associated booklets. Only approved
imitation fuel, available from Burley Magiglo., should be used with this appliance.
5. It is recommended that a fire guard complying with BS 8423 be fitted for the protection of
young children, the elderly or infirm.
6. This fire is intended for decorative purposes only.
7. The user is warned not to throw any rubbish onto the fire or to disturb the fuel bed.
8. The user is advised that the ceramics used within this appliance require extra care whilst
cleaning. Please refer to the Cleaning Instructions.
Ventilation Requirements
1. For models with heat inputs not exceeding 6.9kW additional ventilation is not normally
required in the room that the fire is fitted. However, if spillage is detected during spillage
test additional ventilation may be required. In GB reference should be made to BS
5871:Part 3, and in IE, reference should be made to the current edition of I.S.813 which

Page 2
makes clear the conditions that must be met to demonstrate that sufficient ventilation is
available.
2. Models with heat inputs in excess of 6.9kW require a minimum of 100cm2ventilation in the
room where the fire is installed when installed in Great Britain (GB) and in IE, reference
should be made to the current edition of I.S.813 which makes clear the conditions that
must be met to demonstrate that sufficient ventilation is available.
3. Any purpose provided ventilation must be checked periodically to ensure it is free from
obstructions.
4. When fitting the fire in Northern Ireland (NI), purpose provided ventilation must be
provided in accordance with the rules in force.
5. In other EC countries equivalent rules in force must be used.
Flue Requirements
The flue serving this appliance shall have no cross sectional dimension less than 175mm
(7”) e.g. 225mm (9”) by 225mm (9”) Masonry chimney or 175mm (7”) diameter clay liner.
However, should the model being installed have a heat input of 6.9kW then the flue
requirements as set out in SECTION 3.2.2 may be applicable. Please refer to the full Flue
and Chimney Requirements within the Installation Instruction section.
Gas Supply
1. This range of decorative gas fires are suitable for use with either Natural Gas (G20) at
20mbar supply pressure, or LPG (G31) at 37mbar supply pressure (please check
appliance data plate for compatibility).
2. A separate means of isolating the gas supply should be provided near to the appliance to
facilitate servicing. For this an isolating valve has been supplied.
Electrical Supply
Not applicable to this range of appliances.
1.1. Important Note About ODS Pilot
This fire is fitted with an ODS pilot which causes the appliance to shut down in the event of a
reduction of oxygen (e.g. caused by poor ventilation) in the room. Should this happen, follow
the lighting instructions to re-light the fire. In the event that the fire should shut down again,
do NOT attempt to re-light it but contact your gas installer for remedial action to be taken.
Under no circumstances should it be adjusted or put out of action by the installer
or the user. In case the pilot needs replacing, only the approved part (available
from your supplier or Burley Magiglo.) should be fitted. Note: if any part of the
pilot assembly becomes faulty the complete assembly will need replacing.

Page 3
1.2. Fire Fret Dimensions
All models can be used with the Burley Magiglo range of frets or any other fire fret that
falls within the dimensions shown below
The fireplace opening must be suitable in size to accommodate the fire being
installed. If the appliance is to be used with other fireplace components, the
installation must allow a minimum of 5 square inches of free air space below the
base of the fire.
Minimum opening
(free air) in fire fret
Minimum opening
(free air) in ash pan cover
Figure 1
Fire Front Specification
Height to Centre (A) Maximum 9 Inches (23cm)
Minimum 7.5 Inches (19cm)
Ash Pan Cover Height (B) Maximum 3.5 Inches (9cm)
Minimum 2.5 Inches (6.4cm)
Ash Pan Cover Free Air Opening Minimum 5 sq. Inches (32.3cm2)
Fire Fret Free Air Opening Minimum 15% of total fire front
area above the base of
the fire
Ash Pan Cover Length (C) Maximum 13.5 Inches (34cm)
Minimum 12.5 Inches (32cm)

Page 4
This page is left intentionally blank

Page 5
2.USER INSTRUCTIONS
2.1. Lighting Procedure
Your fire will be fitted with one of the following different types of gas control valves. Identify the
control system on your fire as shown and follow the appropriate operating instructions in the
appropriate section.
Control Valve Operation Control Type
+Manual =
Manual BM
Control
See
Section 2.1.1
on Page 6
+Manual =Manual Mertik
Control
See
Section 2.1.2
on Page 7
+ =
Remote Control
See
Section 2.1.2
on Page 7
+
=
Optimum Control
See
Section 2.1.4
on Page 9
+=
Trim Switch
Control
See
Section 2.1.4
on Page 9

Page 6
2.1.1. Lighting Procedure (Manual BM Control)
1. Ensure that the arrow on the control
knob is pointing towards the OFF
position as shown in Figure 2. Press in
the knob and slowly turn anti-clockwise
until a click is heard. The spark should
now light the pilot. On first lighting, it
may require several attempts to allow the
pilot light to be purged of air.
2. The pilot can be viewed either at the
front centre of the fire, or to the right
hand side.
3. Once the pilot flame is established, hold
the control knob in for approximately 10-
20 seconds and release. The pilot
should now remain alight. Repeat the
procedure if necessary.
4. The arrow should now be pointing to the
PILOT position as shown in Figure 3.
5. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.
6. Once the pilot is established, the main
burner can be operated by turning the
control knob anti-clockwise. The preset
minimum is found with the arrow in the 9
o’clock position as shown in Figure 4.
7. The preset maximum (as shown in
Figure 5) is found by turning the control
knob fully anti-clockwise. The control is
infinitely variable between the two preset
limits.
8. To extinguish the main burner, push the
control knob in and turn clockwise until
the arrow is in the PILOT position, then
release.
9. To extinguish the pilot, push the control
knob in and turn it clockwise until the
arrow is in the OFF position, then
release.
Figure 2 - Off Position
Figure 3 - Ignition Position
Figure 4 - Minimum Position
Figure 5 - Maximum Position

Page 7
2.1.2. Lighting Procedure (Manual Mertik Control)
1. Whilst pushing the IGNITION KNOB in
(see Figure 6), turn it anticlockwise to
the pilot flame position as shown in
Figure 7. During this process, the
spark ignition will have operated and lit
the pilot flame. On lighting the pilot
flame continue to depress the ignition
knob for a further 10 - 12 seconds then
slowly release. The pilot flame should
stay alight. If the flame goes out repeat
the procedure above to establish the
pilot.
2. If the spark unit fails to light the pilot,
the appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
3. Turn the IGNITION KNOB anticlockwise
to the main flame position as shown in
Figure 8.
4. Turn the GAS RATE ADJUSTING
KNOB fully anticlockwise (until you
reach the stop position) i.e. the
maximum gas rate. See Figure 9.
5. The main burner will have cross-lit from
the pilot.
6. Now the gas rate can be adjusted to the
desired setting by turning the GAS
RATE ADJUSTING KNOB to any
position between the pre-set high and
low.
7. To switch off the main burner turn the
IGNITION KNOB to the ‘Pilot burner
only Position’ as shown in Figure 7.
The appliance may be left in this
standby mode if desired.
8. To turn the pilot off turn the Ignition
Knob on the control valve fully
clockwise to ‘¦’ position.
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.
Ignition knob
Gas rate adjusting knob
Figure 6 - Off Position
Figure 7 – Pilot burner only
Figure 8 – Main burner operational, but gas flow off
Figure 9 - Main Burner operational & Maximum Gas
Rate

Page 8
2.1.3. Lighting Procedure (Remote Control)
1. Press the bottom button on the remote
handset until clicking is heard on the
valve, and the gas rate adjustment knob
is at the off position.
2. With gas available at the valve press the
IGNITION KNOB in and turn it
anticlockwise to the pilot flame position.
A click of the piezo igniter will be heard
and a spark will appear at the electrode.
At the same time the gas will flow to the
pilot burner and should be ignited by the
spark. Repeat the procedure until the
pilot flame is established.
3. Keep the knob pressed in for a further 10
- 12 seconds and slowly release it. The
pilot flame should stay alight. If the
flame goes out repeat the procedure
above to establish the pilot.
4. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
5. Turn the IGNITION KNOB
anticlockwise to the Main Burner
Operation position as shown in Figure
10.
6. Using the HANDSET (as shown in
Figure 11) press and hold both the top
and the small button together until the
main burner goes to full rate and clicking
can be heard from the valve. During this
process the main burner will ignite from
the pilot.
7. By pressing the two buttons together (to
increase the gas rate) and the lower
button only (to decrease the gas rate)
the valve can be manipulated to select
the desired gas rate between maximum
and minimum. By pressing the buttons
in short bursts you will be able to adjust
the gas rate in small steps.
8. To turn the fire off, continuously press
the lower button until the flame dies
down and clicks can be heard from the
valve. Release the button as soon as
the clicks are heard.
9. The fire can safely be left in this position
at all times, however to prevent
unauthorised or accidental use (say by
children) it is recommended to turn the
IGNITION KNOB to the pilot flame
position by turning it 90 degrees
clockwise. To turn the pilot off, turn the
IGNITION KNOB fully clockwise.
NOTE: The clicking sound
made by the valve is the
operation of the valve clutch,
and indicates either maximum
or minimum positions.
IGNITION
KNOB
FULL RATE
POSITION
MAIN BURNER
OFF POSITION
PILOT ONLY
POSITION
MAIN BURNER
OPERATION
GAS RATE
ADJUSTMENT
KNOB
Figure 10 – Gas Valve
Press these
two buttons
together to
increase
gas rate
Press this
button to
decrease
gas rate
Figure 11 - Handset Operation
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.

Page 9
2.1.4. Lighting Procedure (Optimum Control and Trim Switch Control)
1. Ensure the main burner is off by pressing
the button on the trim marked
(‘small flame/dot’) until clicking is heard
on the valve (see Figure 12/Figure 13).
2. With the gas available at the valve press
in the IGNITION KNOB and turn it
anticlockwise to the pilot flame position
(see Figure 14). A click of the piezo
igniter will be heard and a spark will
appear at the electrode. At the same
time the gas will flow to the pilot burner
and will be ignited by the spark. Repeat
the procedure until the pilot flame is
established.
3. Keep the knob pressed in for a further 10
- 12 seconds and slowly release. The
pilot flame should stay alight. If the
flame goes out repeat procedure above
to establish the pilot.
4. If the spark unit fails to light the pilot, the
appliance may be lit manually by
applying a lighted match or taper to the
pilot jet and following the above
procedure.
5. Turn the IGNITION KNOB
anticlockwise to the main flame
position.
6. Press and hold the (‘large flame’)
button (in Figure 12/Figure 13) until
clicking is heard (fully open).
7. The main burner will have cross-lit from
the pilot.
8. Now the gas rate can be adjusted to the
desired setting by pressing the
(‘small flame/dot’) button. Any rate
between the pre-set high and low can be
obtained using the two buttons.
9. To switch off the main burner press and
hold the (‘small flame/dot’) button
until clicking is heard from the valve
(OFF position).
10. The fire can safely be left in this position
at all times, however to prevent
unauthorised or accidental use (say by
children) it is recommended to turn the
IGNITION KNOB to the pilot flame
position by turning it 90 degrees
clockwise. To turn the pilot off, turn the
IGNITION KNOB fully clockwise.
NOTE: The clicking sound
made by the valve is the
operation of the valve clutch,
and indicates either maximum
or minimum positions.
TRIM HIGH
LOW
OFF
/
Figure 12 – Trim Switch
Figure 13 - Wall Switch
IGNITION
KNOB
GAS RATE
ADJUSTING
KNOB
GAS VALVE
Figure 14
NOTE: No attempt should be
made to relight the fire for at
least 3 minutes after the pilot
flame has been extinguished
either intentionally or
unintentionally.

Page 10
2.2. Battery Replacement (Remote Control)
2.2.1. Handset
1. On the reverse of the handset remove
the battery cover by pressing down at
the top of the cover and sliding down.
2. Remove and unclip the old battery and
replace with a new PP3 9V battery.
3. Replace the cover.
Figure 15 – Handset
Press here and
slide down
Figure 16
2.2.2. Receiver Unit
1. Remove the receiver unit from under the
fire burner (or from wherever positioned
if mounted remotely) and remove the
battery compartment cover (see
diagram).
2. Replace the old batteries with new ones,
ensuring they are inserted in the correct
polarity.
3. Replace the cover on the receiver unit,
ensuring that it is securely closed.
4. Return the receiver unit to its original
mounting position.
Figure 17
CAUTION: With the exception of battery replacement, the battery holder must be
located within the heat shield at all times.

Page 11
2.3. Battery Replacement (Optimum Control)
1. The battery pack is mounted inside the
wall-mounting box behind the wall switch
plate.
2. To change the batteries remove the two
small screws securing the wall plate
using a small screwdriver.
3. Remove the battery pack from the wall
box and replace the spent batteries with
new ones (4 off 1.5V AA batteries)
ensuring correct polarity.
4. Insert the battery pack back into the wall
box and refit the wall plate ensuring that
it is the right way up.
5. Secure with screws.
REAR OF WALL
PLATE
CABLE TO
VALVE
BATTERY
PACK
(4 x 1.5 VAA
BATTERIES)
LOW/OFF
SWITCH
HIGH
SWITCH
brown brown
brown
blue
blue
blue white
black
Figure 18
2.4. Battery Replacement (Trim Switch Control)
1. Open the Control Cover.
2. Slide out the battery holder from under
the fire.
6. Replace all batteries with new ones (4 x
AA batteries required). Ensure that the
batteries are inserted with correct
polarity in the holder.
7. Replace the battery holder into the
battery compartment.
8. Close the Control Cover
BATTERY
HOLDER
HEAT
SHIELD
Figure 19
CAUTION: With the exception of battery replacement, the battery holder must be
located within the heat shield at all times.

Page 12
2.5. Fuel Effect Layout
You fire has been supplied with either Coal or Pebble effect. Please refer to the relevant
section for instructions on how to arrange the imitation fuels.
Fuel Effect Tray Type Refer to
Coal Effect Natural Gas & LPG Section 0
Pebble Effect Natural Gas Section 2.5.2
It is recommended that the imitation fuel be left alone once the desired flame pattern has been
achieved. Constant moving of the imitation fuel will cause the fuel to disintegrate
and/or cause discolouration.
RCF Advice:
This product may use Components (Coals, Pebbles & Ceramic backs)
containing Refractory Ceramic Fibres (RCF), which are man-made vitreous
silicate fibres. Excessive exposure to this material may cause irritation to eyes,
skin and respiratory tract.
Therefore during installation and servicing we recommend that you use a HEPA
filtered vacuum to remove any dust and soot accumulated in and around the fire
before and after working on the fire, to ensure that the release of fibres from
these RCF articles is kept to a minimum.
We recommend that you should follow the normal hygiene rules of not smoking,
eating or drinking in the work area.
When replacing Components containing Refractory Ceramic Fibres (RCF), we
recommend that the replaced items are not broken up, but are sealed within
heavy duty polythene bags, and clearly labelled as RCF waste. RCF waste may
be disposed of in suitably licensed landfill sites.
WARNING: Do not touch the fire when it is alight. The fire will remain very hot
for a while after extinguishing.
Sooting on the pebbles may be observed. This is perfectly normal. Periodically
operating the Fire at various rates may burn this soot away. If excessive sooting
is observed, this may be an indication that the pebbles are laid incorrectly –
please refer to instructions.

Page 13
For clarity, the Coal Effect Layouts start on the next page

Page 14
2.5.1. Coal Effect Layout
This fire is supplied with different sizes of
ceramic coal, with the quantity supplied
being dependant upon the type of burner:
E16 E18 EV16 EV18
Small
Square
Coals 6 7 6 7
Medium
Square
Coals 9 10 9 10
Random
Coals 21 24 20 25
Half Size
Coals 3
(LPG
Only)
4
(LPG
Only)
3
(LPG
Only)
4
(LPG
Only)
Aeration
Tubes 2 3 2 3
Proceed with the coal layout as follows: -
1. Following the appropriate set of
drawings, form the first layer, using the
Small square and Medium square
coals, placing the aeration tubes on the
shaded areas.
2. Unpack the Random coals and form the
second layer, ensuring that none of
these coals come into contact with the
burner board.
3. Using more of the Random coals, form
the front and top layers.
4. Packing the coals too tightly together will
result in a poor flame picture. The best
results come from a ‘loose’ fuel build.
5. Do not place any coals immediately over
the pilot assembly.
6. After the appliance has been allowed to
warm up (operated on high setting for
10-15 minutes), small adjustments (using
a small pair of tongs) may be made to
the top layer to achieve the desired
flame picture.
7. It is recommended that the coals be left
alone once the desired flame picture has
been achieved. Constant moving of
the coals causes the coals to
disintegrate and/or cause
discolouration.
WARNING: Do not touch the
fire when it is alight. The fire will
remain very hot for a while after
extinguishing.
370mm
196mm
Medium
Square Coals
Aeration Tubes
Equally spaced
Small Square Coals
Half Size Coals
(LPG Only)
Random Coals
Figure 20 – Elite 16” Fire
Medium
Square Coals
Aeration Tubes
Equally spaced
Small Square Coals
Half Size Coals
(LPGOnly)
196mm
420mm
Random CoalsRandom Coals
Figure 21 – Elite 18” Fire

Page 15
MEDIUM
SQUARE
COALS
AERATION TUBES
SMALL SQUARE
COALS
HALF SIZE
COALS
(LPG Only)
RANDOM
COALS
Figure 22 – Elite 16” Victorian
MEDIUM
SQUARE
COALS
AERATION TUBES
SMALL SQUARE
COALS
HALF SIZE
COALS
(ON LPG
BURNERS
ONLY)
RANDOM COALS
Figure 23 – Elite 18” Victorian

Page 16
2.5.2. Pebble Effect Layout (Natural Gas Only)
The fire is supplied with ceramic pebble sets
as follows:-
E16 E18 EV16 EV18
Large
Pebbles
(A, B & K) 18 22 15 18
Medium
Pebbles
(
C & D
)
3 4 8 10
Flat
Pebbles
(
H
)
4 4 4 4
Front
Pebbles
(E) 6 7 6 7
Aeration
Tubes 4 6 4 6
For models ME16 and ET16 refer to Figure
24.
For models ME18 and ET18 refer to Figure
25.
For model EV16 refer to Figure 26.
For model EV18 refer to Figure 27.
NOTE: When placing pebbles on the tray
ensure the lettering on them is facing down
and into the fire. After every step of pebble
laying ensure that they are stable.
Proceed with the pebble layout as follows:-
1. Unpack the aeration tubes, Pebbles H,
& E and place them on the tray as
shown in the relevant figure ensuring
that the port holes and the cross ignition
slot on the right hand side remain clear.
Note that the aeration tubes should be
placed on their back, with the legs facing
up ensuring that as few port holes are
blocked as possible.
2. Using Pebbles A, B & K position as
shown to form the second layer.
3. Using Pebbles A, B, C & D position as
shown to form the front and third layers.
4. Using the remaining Pebbles A, form the
final layer.
5. Small adjustments to the top layer may
be made to alter the flame pattern if
desired flame after the fire has been
turned on. A small pair of tongs should
be used for this.
6. It is recommended that the pebbles be
left alone once the desired flame pattern
has been achieved. Constant moving
of the pebbles causes the pebbles to
disintegrate and/or cause
discolouration.