Makita ML700 User manual

Rechargeable Torch
Power source
Makitabattery pack
Model 7000
QC7.2
V
(rechargeable Ni - cd
MODEL MLTOO
Net
weight
Bulb Switch Dimensions
7.2 V.
See-sawtype 67 mmx 70 mm x 268 mm
550 mA ON-OFF (2-5/8") x (2-3/4") x (10-1/2") 2oog
INSTRUCTION MANUAL

Thank you for your purchase of this Makita Rechargeable Torch.
To use the torch effectively and obtain maximum performance, you are encouraged to
read these instructionscarefully before operation. Keep the instructionsto refer to later
on
as well.
SEVEN POINTS TO REMEMBER:
1. The finish on the reflector is the result of special surface treatment. Never remove the
lens and attempt to wipe or touch the reflector surface with your hand.
.
2. Never attempt to short the bulb using
tweezers, metal tools, etc.
.
3. Use only the Makitapower pack (batterycartridge Model 7000).
4. Do not wash the torch with water or keep it in a damp place.
5. Although the torch is ruggedly constructed, handle it gently, do not disassemble it
6, Check the charge level at least once a month, especially ifyou use the torch for emer-
7. If the torch gets wet, dry it off as soon as possible before use. Be sure to switch
needlessly or forcibly twist the head.
gency purposes(inyour car, etc.).
"OFF" after using. It the light seems dimmer, recharge the battery pack.
HOW TO USE
LOADING BATTERY CARTRl DG E
Open the set plate inthe heel of the torch.
It snaps open with thumb or finger pres-
sure. The minus
(-) terminal side should
be on the groove side of the torch barrel,
when you insert the battery pack. Slide in
pack
all the way before snapping set plate
firmly back into position.
2

TORCH OPERATION
1. Press in the ON portion of the switch
to put the torch on.
Depressthe OFF portionto put
it off.
2. The head has three angle settings to
enable use in tight quarters or for angl-
ing the beam in
a given direction.
ATTACHING RED FILTER
Secure the red filter ring onto the lanyard to prevent loss. Filter slips onto torch head in
arrow direction.
REPLACING LIGHT BULB
1. There is a spare bulb kept inside the torchcase. Always switch OFF the torch before
replacingthe bulb.
2. The ring screws clockwise for installa-
I
3. Unscrew the ring and remove together the ring, reflector and bulb. By unscrewing
(counterclockwise) the black fitting holding the bulb, the bulb can be removed from
the back of the reflector.
4. To reinstall the bulb, follow the reverse of the above procedure.
5. See your nearest Makita representative or the point of purchase when buying new
bulbs. Be sure touse the same type bulb
(7.2 V, 550mA).
3

MAINTENANCE
Use a cloth dampened in a mild detergent to clean off the torch from time to time.
Then wipe dry with
a dry cloth. Benzene, thinner and other volatile agents will damage
the plastic,
so never use them.
ACCESSORIES
Red filter, lanyard(cord)
SERVICE
If any problemsdevelop, consult your nearest Makitaservice center or dealer
Recycling the Battery
The only way to dispose of a Makita battery is
to recycle it. The law prohibits any other
method
of disposal.
I
@
Ni-Cd
I
To recycle the battery:
1. Remove the battery from the tool.
2. a). Take the battery to your nearest Makita Factory Service Center
or
b). Take the battery to your nearest Makita Authorized ServiceCenter or
Distributorthat has been designatedas a Makita battery recycling location.
Call your nearest Makita Service Center or Distributor to determine the location
that provides Makita battery recycling. See your local Yellow Pages under
"Tools-Electric':
Makita Corporation
3-11 -8, Sumiyoshi-cho,
Anjo, Aichi
446 Japan
883370A0 PRINTED IN JAPAN
1994 - 2 - N