Makita 2702 Manual

2702
CONCEPT AND MAIN APPLICATIONS
Specifications
Standard equipment
Optional accessories
Model 2702,2703 are improved versions of the existing Model
2708.Their brief benefits are;
*Large table
*Easy operation for adjusting depth of cut and bevel angle
*Excellent chip/sawdust ejection
*Self-a1igning rip fence with a single handle control
*Tool storage pocket
*Epuipped with electric brake
*Switch is equipped with auto-off function, which will 
automatically change swirch position from "ON" to "OFF"
when power down while switch-on. (Only for Europe)
210mm(8-1/4"),255mm(10")Table Saw
Models No.
Description
686mm (27")
560mm (22")
308mm (12-1/8")
Continuous Rating (W)
Voltage (V) Current (A) Cycle (Hz) Input Output Max. Output(W)
100
120
220
230
240
15.0
15.0
7.9
7.5
7.2
50/60
50/60
50/60
50/60
50/60
1430
1650
1650
1650
1650
760
950
950
950
950
1900
2200
2200
2200
2200
No load speed 4,600rpm
U.S.A.,Canada and Mexico 15.88mm(5/8")
Europe(2702 only) 30mm
Arbor diameter
Other countries 25.4mm(1")
2702 210mm(8-1/4")Blade diameter 2703 255mm(10")
Net weight 18Kg(40.01bs)
Cord length 2.5m(8.2ft)
Cutting capacities (HxW)
2702 2703
068mm(2-11/16") 91mm(3-9/16")
45 47mm(1-3/4") 63mm(2-1/2")
Ruler Ass' y------------------------------------------------ 1 pc.
Angle Rule Ass' y----------------------------------------- 1 pc.
Wrench 19-------------------------------------------------- 1 pc.
Wrench 13-22---------------------------------------------- 1 pc.
Holder Cap Opener----------------------------------------1 pc.
Ring----------------------------------------------------------1 pc. (except for U.S. A. ,Canada, Mexico and Europe)
T.C.T. Saw Blade 210(2702)-----------------------------1 pc.
T.C.T. Saw Blade 255(2703)-----------------------------1 pc.
Stand Set-----------------------------------------------------1 pc. (For Europe)
Stand Set Joint (connecting to Vacuum Cleaner 406 or 410)
Subtable R,L Center Cover(For U.S.A.,Canada and Mexico)
Dado Head Set(For U.S.A.,Canada and Mexico) Outer Flange(For U.S.A.,Canada and Mexico)
The standard equipment for the tools shown may differ from country to country.
New Tool
TECHNICAL INFORMATION

Repair
Greasing
Before assembling, grease the MAKITA grease on the turntable and moving faces shown below.
Disassembling of motor and frame
Before disassembling, disconnect the saw cutter and safety cover.
(i)
(ii)
Bevel gear Screw bar retainer
Guide bar retainer
Movable points on the frame
Frame - moving face between slide sheets
Frame retainer - Moving face between leaf springs
Up/down guide shaft, up/down screws, teeth for up/down on the motor(saw)
Teeth for tilting on the motor(saw)
Elongation hole window on the plate(steel plate for fixing inclination)(both front/back sides)
1. Turn the machine upside down and place the motor(saw) with inclined 45..
2. Shift the motor to the position where the screws for mounting the screw bar retainer can be loosened.(See (i)
on the below figure.)
3. Pull out the spring pin mounting the bevel gear for up/down in the direction shown on the figure to take away
the bevel gear.(See the (ii) on the below figure.)
4. Disconnect the screws mounting the guide retainer and screw bar retainer.

Note) The stay should pass through
the hole for the frame.
(The stay can be assembled later.)
Guide bar Note) Place the gear housing plate
under the guide plate.
Frame
Screw bar
Bevel gear
Flat washer
Note) Set in a way that the two flat washers hold
the screw bar mounting points on the frame.
Set the motor on the position where the screw
for mounting the screw bar retainer can be fastened.
Assembling the frame to the motor
1. Set the flat washer 12(2 pieces) on the screw bar, and assemble the bevel gear mounted with the spring pin on
 the gear housing.
2. Insert the guide bar into the gear housing.
3. Set the above parts on the frame while using care on the points shown below.
4. First assemble the guide bar at screw bar mounting side using the guide bar retainer.
5. Next assemble the guide bar at stay mounting side using the guide bar retainer.
6. At last assemble the screw bar using the screw bar retainer.

Assembling the frame to the table
Assembling of the bevel lock lever
15°~30°
Cutter edge of the table
Assemble so that these space
may become the same.
Adjust block
Adjust the adjust block so that the saw cutter can be parallel to the cutter edge of the table.(It can be adjusted after
assembling.)
Adjust the mounting position so that you can get the positions shown on the below figure when fastening the bevel
lock lever at maximum.

Circuit drawing
<High pressure specifications>
1
2
3
65
P2
P1
5
3
4
1
2
P2
P1
Cab tire cord
White White
Red Yellow
Black Black Filed
Switch
9
6
3
25
P2
P1
Cab tire cord
Cab tire cord
White White
Red Yellow
Black Black Filed
Switch
Filed
Switch
Switch
Note: The Noise Supressor
is not used in some areas.
Note: The Noise Supressor
is not used in some areas.
Violet Violet
White
White
Red
Yellow Yellow
Black
Orange
color
Orange color
5
3
8
9
6
P2
P1
Cab tire cord
Filed
Note: The Noise Supressor
is not used in some areas.
Violet Violet
White
White
Red
Yellow Yellow
Black
Orange
color
Orange color
Circuit drawing :
<Low pressure specifications>( :connector at closed end)
Noise
Supressor
Noise
Supressor
Noise
Supressor
Noise
Supressor