Mami M1 User manual

Panic Button
Medical Rescue Button
Fire Button
Gsm Communication Indicator
Armed / Disarmed / Triggered Indicator
Programming Button
(Learn button)
Congratulations and thank you for purchasing the M1 Alarm System!
The M1 Alarm System notifies your Armed Response company when there is a crime or a need for help in your home
The M1 Alarm System works like a cell phone, every time the alarm is activated the system calls your Security
Company to summon Help
Adjustable Movement detector:
This sensor picks up any movement within 8mt of the M1and will
trigger the siren connected to the unit.
Only activate the movement sensor when there are no people at
home or you have retired to the bedroom. When the sensor detects
Panic button (BLUE) : The Blue button has 2 functions which depend on the duration of the press.
Silent Panic – If the Blue button is pressed for 1 second , only a control room call is sent and the siren and
strobe will not be activated.
Normal Panic – If the Blue button is pressed for 3 seconds or more, the siren and strobe will be activated
and a call to control room will be sent.
Medical Rescue Button (GREEN): When pressing this button a call the to control room will be sent
indicating that medical attention is required
Fire Alarm Button (RED) : When pressing this button, a call the to control room will be sent
indicating that a response to a Fire is required.
ŸGPRS Enabled
ŸWireless movement Detectors
Ÿ12 months Detector Battery Autonomy
ŸRemote control for arm/disarm/panic activation
Ÿ 24 hour Standby System Battery Autonomy
Ÿ GSM & Radio Jamming Detection
Ÿ Extremely easy to install
Ÿ Expandible to 8 movement detectors and 8
remote controls
Wireless Detectors
Mains is ON when
all 3 lights are ON
KIT components
M1
Simple but Powerful
GPRS Alarm System
Screw to remove cover
holes for wall
mounting
(use screws and
wall plugs provided)
AREA PROTECTED
M1
DOOR
WINDOWS
10 Meters
3 screws and 3 wall plugs are supplied with the kit .
Use the holes provided on the base of the box for mounting it on the wall.
ideally the unit should be mounted at a higth of 2 mt from the floor (with standard lens)
AREA PROTECTED
Different lenses are available for different type of detection coverages
e.g. horizontal/ long and narrow.
AREA PROTECTED
page 1
FEATURES
( FIG 1
( FIG 2 )
2 Meters
( FIG 2 )
1 Meter

+
--12 +
+
-+
-
POWERSIREN
2A FUSE
STAND BY BATTERY
INSTALLATION :
TO AC POWER
2- connect leads from the UNPLUGGED external transformer (observe polarity)
3- Connect battery to the on board BATTERY connector
12
1- connect external siren (observe polarity)
Resetting the system
4- Call control room to activate the unit and wait till lights in buttons A, B and C light up
3
Power-up and activation:
Adding a Remote Control :
:
1- press button P (FIG 4) at the bottom-right of the unit till 1 beep is heard and the W light flashes fast
W
G
S
P
( FIG 3 )
( FIG 4 )
( FIG 3)
2- press the RED button (Panic) on the remote control till One Beep is heard
(A two beep signal means that that code is already stored in memory)
Adding Movement Detectors (PIR) :
2- while in this mode open the cover of the PIR detector that needs to be memorized/added.
This will make the unit transmit a tamper signal which will be recognized by the panel as being one
from a sensor and will be stored it in memory.
(A two beep signal means that that code is already stored in memory)
2- While pressing buttons C (RED in front ) and P(at the bottom-right) apply AC power.
the unit will indicate a RESET TO FACTORY DEFAULT by beeping continuously
1-disconnect battery & mains
A
B
C
OPERATION:
ARMING the M1 is achieved by pressing the ARM button ( BLUE ) .
The unit will confirm with ONE beep.
DISARMING the M1 is achieved by pressing the DISARM button ( YELLOW ) .
Red button is for (P) PANIC and activates Siren & Strobe
Yellow button is to (D) DISARM the system
REMOTE CONTROL:
Blue button is to (A) ARM the system
Green button is the (S) SILENT PANIC
A four button Remote Control is used to perform all the functions required by the system:
( the range is 100 meters)
The unit will confirm with TWO beeps.
Wireless System
GSM
1- press button P (FIG 4) at the bottom-right of the unit till 1 beep is heard and the W light flashes fast
. The code is now memorized
4- the system is now ready to be programmed AS NEW . (See above)
3- remove power , wait 3 seconds and reconnect AC power and /or Battery
If Triggered the Siren will sound for 2 Minutes
When Armed the Red Led will flash at 2 seconds intervals
When Triggered the Red Led will flash 3 times per second
ALARM ACTIVATION:
ALARM RESET :
Press the Yellow Button on the Remote Control
21/4/2016
MAMI
MANUFACTU RING AND MIN OR INVENTI ONS
21 Hubert Mathew road Illio ndale, Sou th Africa
TEL +27 ( 011)452- 4737 FAX [phone]
e-mail - sales@ma mi.co.za
Web site - www.m ami.co.za
M1
page 2
P
MAMI
5- NO function can be performed on the M1 unless the system has been activated