Manhattan 158046 User manual

SATA 150
CONTROLLER
PCI CARD
USER
MANUAL
Model 158046
MAN-158046-UM-0508-01

Thank you for purchasing this MANHATTAN
®
SATA 150 Controller PCI
Card, Model 158046.
Compatible with eSATA and SATA 150/300 drives — including CD, DVD
and HDD — it supports data transfer rates of up to 1.5 Gbps and drives
above 137 GB. Using 48-bit LBA (logical block addressing), it breaks the
size limit of 137 GB hard drives to support larger storage devices, and
compliance with PCI Specication, revision 2.2 and SATA 1.0 specications
ensures that most desktop computers and connected SATA devices can
operate at peak performance.
The easy-to-follow instructions in this manual help make installation of
the card quick and simple, so you’ll also soon be enjoying the benets
of these additional features:
• One eSATA and one internal SATA connection
• Regular and low-prole slots
• Plug and Play installation — Windows compatible
• Lifetime Warranty
System Requirements
• Windows 2000/XP/Vista (Server 2003 users can follow the procedures
for Windows 2000/XP throughout this manual)
• Available PCI card slot
• CD-ROM drive
Package Contents
• SATA 150 Controller PCI Card, Non-RAID
• Regular and low-prole brackets
• User manual and driver CD

HARDWARE INSTALLATION
1. Turn off your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCI slot.
4. To install the card, carefully align the card’s bus connector with the
selected PCI slot on the motherboard. Push the board down rmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Replace the cover, reconnect the power cord and turn the power on.
SOFTWARE INSTALLATION
With Initial Installation of Windows 2000/XP
Follow this procedure for a new installation of Windows 2000/XP (or
2003 Server) if you boot from a device attached to the SATA 150
Controller PCI Card. IMPORTANT: With Windows 2000, rst edit the
txtsetup.oem le on the driver installation disk by deleting the line from
the [Cong.Si3112] section that reads:
value = Parameters\PnpInterface, “5”, REG_DWORD, 1.
1. Insert your Windows installation CD into the CD/DVD-ROM drive (or
use the Windows 2000 boot diskette #1 and a oppy drive if your
system can’t boot from the CD).
2. Press “F6” for third-party SCSI or driver installation at the beginning
of text mode installation. Press “s” when the prompt on the Setup
screen asks if you want to specify an additional device; then insert the
driver CD and press “Enter.” On the subsequent menu that displays,
select the controller installation process that corresponds to the version
of Windows being installed; then press “Enter.”
3. When prompted to continue with text mode setup, press “Enter” again.
4. Follow the on-screen setup instructions to select the partition and le
system.
5. After Setup examines your disks, it will copy les from the CD to the
hard drive selected above and restart the system. After restarting, the
setup process will resume and nish the installation.
6. Once the operating system installation has completed, you can follow
3 3

the instructions in Verifying Controller Installation to conrm that the
controller has been installed correctly.
With Initial Installation of Windows Vista
1. Insert your Windows Vista DVD into the DVD-ROM drive.
2. When Vista starts from the DVD, change the displayed language and
keyboard preferences as needed and click “Next”; on the subsequent
screen, click “Install now.”
3. Enter your product key and click “Next.”
4. Select the option “I accept the license terms” and click “Next.”
5. Select the option “Custom (advanced).”
6. Click the icon labeled “Load Driver”; in the subsequent “Load Driver”
pop-up window, click “OK.”
7. When the “Select the driver to be installed” screen displays, insert the
driver CD, then select “Silicon Image Sil 3x12 SATALink Controller”
and click “Next.” Windows will now load the driver.
8. The newly installed drive should now be displayed. Click “Drive options
(advanced).”
9. Highlight the unallocated space of the installed drive and click “New.”
In the Size box that displays, specify the size of the partition to be
created to contain the Vista OS installation; then click “Apply.”
10. Select the newly created partition and click “Next.”
11. Follow the on-screen prompts to complete the installation of Vista.
Once the operating system installation is complete, you can follow the
instructions in Verifying Controller Installation to conrm that the
controller has been installed correctly.
With an Existing Installation of Windows 2000/XP
1. As Windows boots, a “Found New Hardware Wizard” message
displays. Click “Next.”
2. Select “Search for a suitable driver for my device (Recommended)”
and Click “Next.”
3. Insert the driver CD and click “Next.”
4. When the wizard says it’s found a driver for the device, click “Next.”
5. If the message “Digital Signature Not Found” displays, click “Yes” to
continue installing the driver.
44

5
6. The wizard will now copy the required les to the system and start the
driver. After starting the driver, the wizard will display a completion
message. Click “Finish” to exit the wizard.
7. Follow the instructions in Verifying Controller Installation to conrm
that the controller has been installed correctly.
With an Existing Installation of Windows Vista
1. As Windows boots, a “Found New Hardware Wizard” message
displays. Select “Locate and install driver software (recommended).”
If the prompt “User Account Control” displays, click “Continue.”
2. On the subsequent screen, select “Don’t search online.”
3. Insert the driver CD and click “Next.”
4. Windows will now begin to install the driver software. If the message
“Windows can’t verify the publisher of this driver software” displays,
click “Install this driver software anyway.”
5. Once the installation is complete, you can follow the instructions in
Verifying Controller Installation to conrm that the controller has been
installed correctly.
Updating the Driver on Windows 2000
1. Right-click on My Computer and go to Properties. In System Properties,
go to Hardware, then Device Manager. Select “SCSI and RAID
Controllers”; then right-click “Silicon Image SiI 3x12 SATALink
Controller” and go to Properties (on the context menu).
2. Go to Driver and click “Update Driver.” Select “Display a list of the
known drivers for this device so that I can choose a specic driver.”
Insert the driver CD, then click “Next.”
3. Click “Have Disk.” When the “Install from Disk” prompt displays, ensure
that the correct drive is specied and click “OK.”
4. Click “Next” until the installation process begins. If a warning about an
unsigned driver displays, click “Yes” to continue.
5. When the installation is complete, a reboot prompt may display. Click
“Yes.”
6. Follow the instructions in Verifying Controller Installation to conrm
that the procedure was successful.
5

Updating the Driver on Windows XP
1. Right-click on My Computer and go to Properties. In System Properties,
go to Hardware, then Device Manager. Select “SCSI and RAID
Controllers”; then right-click “Silicon Image SiI 3x12 SATALink
Controller” and go to Properties (on the context menu).
2. Go to Driver and click “Update Driver.”
3. Select “Install from a list or specic location (Advanced)”; click “Next.”
4. Select both “Search for the best driver in these locations” and “Search
removable media (oppy, CD-ROM...)”; click “Next.”
5. As the installation proceeds, a warning about a “non-logo” (uncertied)
driver may display; click “Continue Anyway.”
6. When installation is complete, a reboot prompt may display. Click “Yes.”
7. Follow the instructions in Verifying Controller Installation to conrm
that the procedure was successful.
Updating the Driver on Windows Vista
1. Click the Start icon, then right-click on Computer and go to Manage (on
the context menu). If a “User Account Control” prompt displays, click
“Continue.”
2. Go to Device Manager in the left-hand panel, then double-click on
Storage Controllers in the right-hand panel.
3. In Storage Controllers, right-click “Silicon Image Sil 3x12 SATALink
Controller” and go to Properties (on the context menu).
4. Go to Driver and click “Update Driver….”
5. Select “Browse my computer for driver software.”
6. Select “Let me pick from a list of device drivers on my computer.”
7. Click “Have Disk….”
8. With “Install From Disk” displayed, either click “Browse” or specify the
path to where the updated driver package resides on the system (for
example, E:\); then click “OK.”
9. Click “Next.” Windows will begin installing the updated driver software. If
a message displays that Windows can’t verify the publisher of the driver
software, select “Install this driver software anyway.”
10. When installation is complete, a reboot prompt may display. Click “Yes.”
11. Follow the instructions in Verifying Controller Installation to conrm
that the procedure was successful.
66

Verifying Controller Installation for Windows 2000/XP
1. Right-click on My Computer and go to Properties, then Hardware, then
Device Manager.
2. Double-click “SCSI and RAID Controllers.” If no yellow exclamation
point (!) or question mark (?) appears to the left of “Silicon Image SiI
3x12 SATALink Controller,” then the driver has started properly.
3. To view information about the devices attached to the controller, right-
click “Silicon Image SiI 3x12 SATALink Controller” and go to Properties
(on the context menu). Then go to Device Info to see the information.
Verifying Controller Installation for Windows Vista
1. Click the Start icon, then right-click on Computer and go to Manage (on
the context menu). If a “User Account Control” prompt displays, click
“Continue.”
2. Go to Device Manager in the left-hand panel, then double-click on
Storage Controllers in the right-hand panel. If no yellow exclamation
point (!) or question mark (?) appears to the left of “Silicon Image SiI
3x12 SATALink Controller,” then the driver has started properly.
3. To view information about the devices attached to the controller, right-
click “Silicon Image SiI 3x12 SATALink Controller” and go to Properties
(on the context menu). Then go to Device Info to see the information.
SPECIFICATIONS
Standards and Certications
• PCI Specication, revision 2.2
• SATA 1.0
• FCC
• CE
General
• 32-bit, 33/66 MHz fully compliant PCI host
• 48-bit LBA supports HDD larger than 137 GB
• Supports two independent SATA 150 channels
• Silicon Image chipset
• Data transfer rate up to 1.5 Gbps
7

Copyright © MANHATTAN
All products mentioned are trademarks or registered trademarks of their respective owners.
www.manhattan-products.com
MANHATTAN®offers a complete line
of PC Components, Peripherals, Cables and Accessories.
Ask your local computer dealer for more information
or visit us online at