Manrose Classic Series User manual

Diagram 2
Diagram 2A
(The ‘new’ ball bearing designed motors provide an extended lifetime of operation)
NOTE: (i) Thefanistobeinstalledsothatthebladesare2.1mabovetheoor.Forbestresults
 thisExtractorFanshouldbettedashighonthewallaspossible,orifpreferred,on
 theceiling.
 (ii) Donotinstalltheunitwithinashowercubicle.Useourshowerfanmodelsno’s
 SF125SorSF125T.
 (iii) Switchoffmainssupplybeforemakingelectricalconnections.Thissystemshould
 beinstalledbyaqualiedelectrician.
 (iv) Thisfanisdoubleinsulatedanddoesnotrequireanearth.
 (v)Wheninstallingfanthroughanexternalwall,anexternalwallgrillemustbetted
at all times.
1. Cuta140mmdiameterholeinthewall.Ifthefanistobexedontotheceilingensurethat
theholeisbetweenthejoists.
2. Fit125mmductingushtotheplaster.
3. Removethecoverfromthefanbysimplyunclippingthefascia.Thefrontcoverscrewand
plugareconvenientlylocatedwithinthefanhousingasshownindiagram1&2.
4. Holdthebodyofthefanagainstthewallorceilingandmarkthefourscrewholesandthe
cableentry.
 IMPORTANT:Ensurethatthefanissquareonwalltheorceiling.
5. Bringpowercableintoposition,asmarked.Allowanextra230mm(9”)protrudingto
facilitate connection.
 Fanshouldonlybeinstalledbyxedwiring,aexiblecordshouldnotbeused.
6. IfanXP125kit-Selectasuitablepositionontheoutsidewallfortheweatherproofcowl.
Carefullyremovethecowlfromitshousingbyleveringgentlyatthesideswithasmall
screwdriver.Cuta140mmholeensuringrstthattheareaisfreefromobstruction.
7. Wiring of Standard Model (see Diagram 2A).
(For remote switch operation).
Thefancanbeconnectedtothelightswitchsothatthefanwillstartwhenthelightisswitched
on. Thefanshouldnotbeaccessibletoapersonusingeithertheshowerorthebath.
NOTE: Allwiringmustbexedsecurelyandthecabletothefanshouldbeaminimumof
1mm2insection.AllwiringmustcomplywithcurrentRegulations.Thissystemshouldbe
installedbyaqualiedelectrician.
FAN0072/0075/0080 Wall Fan and Kits
INSTALLATION INSTRUCTIONS
CLASSIC SERIES
Rotary adjuster
for time delay
Diagram 2B
Manrose is proudly distributed by Ventair Pty Ltd
4 Capital Place, Carrum Downs, 3201 VIC, AUSTRALIA.
Technical Support [phone]
e: [e-mail] | www.ventair.com.au | www.manrose.com.au
Wereservetherighttochangespecicationwithoutpriorwarning
FAN0072/0075/0080 Wall Fan and Kits IM Iss:01 03/20

Diagram 1
IMPORTANT
FAN MUST BE
INSTALLED THIS
WAY UP WHEN
MOUNTED ON WALL
Specications:
 Model: NZNVF120SBB;NZNVF120TBB
 Electrical: 220-240V~50Hz
 FanWattage: 25W
 MaxTemp: 40˚C
 Airow: 36l/s(130m3/hr)
MaxPressure: 35Pa
 SoundVolume: 41dB(A)
 IPRated: IP44(exceptpullcordmodelIP24)
Diagram 1A
8. Wiring of Pullcord Models (see Diagram 1).
(This model is unsuitable for ceiling mounting).
Thisfanhasitsownintegralpullcordon/offswitch.Thefanshouldnotbeaccessibletoa
personusingeithertheshowerorthebath.
NOTE: Allwiringmustbexedsecurelyandthecabletothefanshouldbeaminimum
of 1mm2insection.AllwiringmustcomplywithcurrentRegulations.Thissystemshould
beinstalledbyaqualiedelectrician.
9. Wiring of Timer Model
See Diagram 2 & 2A.
Thefancanbeconnectedtothelightswitchsothatthefanwillstartwhenthelightis
switchedon.Whenthelightswitchorpullcordisswitchedoffthefanwillrunforbetween
20sec&30minutes(pre-setto1minute).Thefanshouldnotbeaccessibletoaperson
usingeithertheshowerorthebath.
Timer Adjustment.
T histimedelaycanbeadjustedbyrstlyswitchingoffthepowertothefanandremoving the
 fascia.Locatetherotaryadjusterasshownin Diagram 2. Theserratedadjusterwheel
 canberotatedusingathumbnailtoadjustthetimersetting.
   +=Rotatetotherighttoincreasethetime(indicatedby+onthediagram)
   -=Rotatetothelefttodecreasethetime(indicatedby-onthediagram)
Only adjust with power switched off.
NOTE: Allwiringmustbexedsecurelyandthecabletothefanshouldbeaminimumof
1mm2insection.AllwiringmustcomplywithcurrentRegulations.Thissystemshouldbe
installedbyaqualiedelectrician.
For timer adjustment see diagram 2B min 30 secs, max 30 mins.
• Isolate the mains supply before making any electrical connections. This system should be
installed by a qualied electrician.
• Fan should only be installed by xed wiring, a exible cord should not be used.
• The appliance is not intended for use by young children or inrm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.
• Precautions must be taken to avoid the back-ow of gases into the room from
the open ue of gas or other open-re appliances when mounted in outside windows or walls.
IMPORTANT