Manrose LED Series User manual

Thank you for purchasing this quality exhaust fan.
To ensure correct function and safety, please read all instructions before using the product and keep all instructions for future reference.
TECHNICAL DATA
Description Order Code
Toilet Fan FAN7030
Bathroom Fan FAN7031
Kitchen & Laundry Fan FAN7032
High Steam Area Fan (with round fascia) FAN7033
High Steam Area Fan (with square fascia) FAN7034
Order Code FAN7030 FAN7031 FAN7032 FAN7033 FAN7034
Supply 220-240V~50Hz 220-240V~50Hz 220-240V~50Hz 220-240V~50Hz 220-240V~50Hz
Duct Size 100mm 150mm 150mm 150mm 150mm
Power 30W 45W 50W 106W 106W
Max. Fan Pressure 93 Pa 147 Pa 210 Pa 220 Pa 220 Pa
Fan Performance 49 l/s, 175m3/hr 77 l/s, 276m3/hr 105 l/s, 378m3/hr 153 l/s, 550m3/hr 153 l/s, 550m3/hr
Specific Fan Power 0.61 W/l/s 0.58 W/l/s 0.48 W/l/s 0.69 W/l/s 0.69 W/l/s
Sound Level 38 dB(A) 40 dB(A) 42 dB(A) 42 dB(A) 42 dB(A)
When using electrical appliances, basic safety precautions should always
be followed to reduce the risk of fire, electrical shock and personal injury.
DIMENSIONS
Order Code Description A B cut out Ø C D
FAN7030 Toilet Fan 272mm Ø240mm 170mm Ø100mm
FAN7031 Bathroom Fan 326mm Ø300mm 197mm Ø150mm
FAN7032 Kitchen & Laundry Fan 328mm Ø300mm 197mm Ø150mm
FAN7033 High Steam Area Fan 328mm Ø300mm 195mm Ø150mm
FAN7034
Configurable
Fans, Fascia and
Duct Connection
Solution
CONTOUR
Note: Airflow data is in accordance with internationally recognised testing standards. Airflow may vary according to style of fascia used.

Configurable
Fascia and
Duct Connection
Solution
CONTOUR
IMPORTANT
This fan unit must be installed by a registered electrician and its installation and connection to the power supply must comply with all current Australian
and New Zealand electrical and building regulations including AS/NZS3000:2017, or latest edition thereof.
The power supply cable must be suitably rated by a registered electrician to satisfy the total load on that circuit.
WARNING
1. This unit may only be used as recommended by the manufacturer in this manual. Any other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons. Contact the manufacturer, or local agent, if required.
2. Isolate the mains supply before making any electrical connections. This system should be installed by a registered electrician.
3. Ensure the unit is properly earthed.
4. The unit must be able to be isolated from the power by means of a disconnect switch meeting current electrical regulations.
5. The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
6. Children should be supervised to ensure that they do not play with the appliance.
IMPORTANT CONSIDERATIONS BEFORE INSTALLING
Planning can make a big difference to the installation time and your satisfaction with the operation of the unit.
1. This fan is to be installed so that the blades are more than 2.2m above the floor.
2. The unit must be mounted outside the shower cubicle.
3. For the exhaust fan to work efficiently, replacement air, of a volume equivalent to the air being extracted, must be able to enter the room. This air
is usually drawn from under the door, or through a slightly open window. If the room is airtight, however, the fan will function poorly.
4. This unit is designed for installation into a flat ceiling only.
5. Before commencing any cutting, check in the ceiling space that there are no obstructions such as ceiling joists and that there is sufficient height
clearance for the housing. Check that the electrical wiring can be routed from the wall switch to the mounting location.
6. If any of the fan supply cords are damaged, they musr be replaced by the manufactuter, its service agent, or similarly qualified persons, in order
to avoid possible damage to the fan motor or controller.
7. Precautions must be taken to avoid the back-flow of gases into the room from the open flue of gas or other open-fire appliances when mounted
in outside walls or soffits.
8. Any changes, or modifications, made, or attempted, to this product, without the prior written approval of the manufacturer, will void any, and all,
stated warranties.
FAN INSTALLATION AND ELECTRICAL CONNECTION MUST
BE CARRIED OUT BY A REGISTERED ELECTRICIAN
BEFORE INSTALLING THE FAN, MAKE SURE YOU HAVE TURNED OFF THE MAIN ELECTRICITY SUPPLY.
DO NOT TURN IT BACK ON UNTIL THE FAN IS FULLY INSTALLED AND READY TO USE.
ALL ELECTRICAL WORK MUST BE CARRIED OUT BY A REGISTERED ELECTRICIAN IN ACCORDANCE
WITH THE LATEST WIRING RULES AS/NZS3000.

Configurable
Fascia and
Duct Connection
Solution
CONTOUR
INSTALLATION
Note: A means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
1. Check the fan is free to rotate.
2. Cut the hole for the fan using the template provided, making sure the area behind the intended position is free from impediments.
3. Product is supplied with lead and plug
4. Plug into a socket outlet and secure fan body using the three (or four) swing fixing arms. Use philips head screw driving to firmly secure but do
not over tighten.
5. Ducting can be attached to the air outlet prior to installing into position.
Note: A standard socket and electrical wiring to an ON/OFF wall switch must be pre-installed. Please arrange a registered electrician to
prepare the socket outlet and ON/OFF wall switch before carrying out the installation of this appliance.
6. Switch the fan ON and check for excessive vibration or noise.
7. If fan is running as desired, secure the fascia by squeezing the spring fasteners and insert into the slot in the fan body. Check that the fascia is
secured firmly and closely to the fan body.
Note: When installing the fan in a bathroom, the duct should decline downwards about 10 degrees.
Ceiling
Fan Body
Fascia
Ventilating Fan Cable Tie Ducting
INDOOR OUTDOOR
Wall
Hood
Ceiling Ventilating Fan No Gap
10º

Configurable
Fascia and
Duct Connection
Solution
CONTOUR
1. Remove the double-sided tape and attach the LED driver to the fan body. (See diag. 1)
2. Plug the Fan and LED driver into a socket outlet. Knock out the stamped tab in the motor body and feed the LED output connector through.
(See diag. 2)
3. Secure fan body to the ceiling using the 3 clips and screw to tighten.
4. Connect the LED connector to the LED driver securely. (See diag. 3)
5. Push the LED cable connector back through the hole so the connectors are hidden in the ceiling cavity. (See diag. 4)
WHEN INSTALLING WITH AN LED FASCIA
Diagram 1
Attach the LED driver to the fan body as shown
Diagram 2
Pull through connector
Diagram 3
Connect connector to the LED driver
Diagram 4
Push LED connectors into ceiling
Note: LED lamp and LED driver are replaceable. To replace – disconnect female and male connectors and replace new LED lamp or
LED driver.
Note: To avoid overheating DO NOT cover the LED driver with ceiling insulation.
6. Secure the fascia by squeezing the fastening springs and insert into the slots in the fan body. Check that the fascia is secured firmly and is sitting
closely to fan body.
Note: Switch the fan on and check for excessive vibration or abnormal noise before installing the fascia.
LED
Driver
Fan
Body

Configurable
Fascia and
Duct Connection
Solution
CONTOUR
MAINTENANCE CAUTIONS
1. Make sure the fan is always switched off before cleaning.
2. Make sure to use the fan with the specified voltage as stated on the rating sticker.
3. Never immerse any part of the fan in water or other liquids.
4. Never use flamable solvent for cleaning the fan.
5. Never allow water to contact the electrical parts such as switch and motor.
6. Never immerse blades or other resin parts in hot water over 60oC.
7. Never install the fan under extreme hot environments.
BEFORE REPAIRING THE FAN, MAKE SURE YOU HAVE TURNED OFF THE MAIN ELECTRICITY
CLEANING, STORAGE AND DISPOSAL
Before cleaning, turn the unit off, cut off the power supply from electrical outlet and wait for the unit to cool down.
• To clean the unit, use a soft cloth to wipe off any dust.
• Do not try to open the unit without a registered electrician. Improperly installed units can be dangerous.
• This product is in accordance with the relevant safety requirements. Repairs should only be carried out by registered electricians using original
spare parts.
If you do not plan to use the fan for extended periods of time, it is recommended that it is cleaned and stored (preferably in its original
packaging) in a cool, dry place.
Do not dispose of electrical products with household waste. Please check with your local council for advice on disposal or recycling. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food
chain, damaging your health and well-being.
w www.manrose.co.nz w www.manrose.com.au
Distributed by Simx Limited
PO Box 14347, Panmure, Auckland 1741, New Zealand
PUB1512 1906

Simx Warranty Information
In this warranty:
We means Simx;
You means the consumer of the Goods
Supplier means the authorised distributor or retailer that sold you the Goods in New Zealand or Australia;
and
Goods means the Simx product accompanied by this warranty and purchased in New Zealand or
Australia.
The benefits provided to you under the following warranty are in addition to any other rights and remedies
available to you under the law:
1. If, during the time from the date of purchase (Warranty Period), there is a defect in the Goods due to
improper workmanship or material, we will replace or repair the Goods without charge. Any replacement
product is warranted only for the time remaining on the original Warranty Period.
2. We are not obliged to replace or repair the Goods under clause 1 if the Goods have been improperly
stored, installed, connected, used, operated, repaired, damaged, abused, tampered with, altered
(without our written approval), or not maintained in accordance with our recommended installation,
connection and operating instructions.
3. We exclude liability for:
a) consequential loss or any other loss or damage caused to property or persons arising from any
cause whatsoever;
b) damage to consumable items such as lamps and starters; and
c) damage arising from normal wear and tear.
4. In order to claim under this warranty you must, within the Warranty Period, return the Goods to the
Supplier, together with the original proof of purchase including the details below:
Supplier Name _____________________________
Date of Purchase _____________________________
Model Number _____________________________
Invoice/Receipt No. _____________________________
5. This warranty does not cover the cost of claiming under the warranty or transporting the Goods to and
from the Supplier.
Our Goods come with guarantees that cannot be excluded under the New Zealand and Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or
replaced if the Goods fail to be of acceptable quality and the failure does not amount to a major failure.
To speak to someone about your Simx product or claiming under this warranty, please contact:
Simx Ltd New Zealand
p: [phone] f: [phone]
www.simx.co.nz
CABAC
Electrical Wholesale Distributor within Australia
p: 133 122 e: [e-mail]
www.cabac.com.au
WESTAFLEX
HVAC Distributor within Australia
p: 03 9458 2122 e: sales@westaflex.com.au
www.westaflex.com.au