Manrose CLASSIC XF125 User manual

Diagram 2
Diagram 2A
We reserve the right to change specification without prior warning
Manrose is proudly distributed by Simx Limited
PO Box 14 347, Panmure, Auckland, NZ. Technical Support [phone]
e: [email protected] | www.simx.co.nz | www.manrose.com.au
(The ‘new’ ball bearing designed motors provide an extended lifetime of operation)
NOTE: (i) The fan is to be installed so that the blades are 2.1m above the floor. For best results
this Extractor Fan should be fitted as high on the wall as possible, or if preferred, on
the ceiling.
(ii) Do not install the unit within a shower cubicle. Use our shower fan models no’s
SF125S or SF125T.
(iii) Switch off mains supply before making electrical connections. This system should
be installed by a qualified electrician.
(iv) This fan is double insulated and does not require an earth.
(v) When installing fan through an external wall, an external wall grille must be fitted
at all times.
1. Cut a 140mm diameter hole in the wall. If the fan is to be fixed onto the ceiling ensure that
the hole is between the joists.
2. Fit 125mm ducting flush to the plaster.
3. Remove the cover from the fan by simply unclipping the fascia. The front cover screw and
plug are conveniently located within the fan housing as shown in diagram 1 & 2.
4. Hold the body of the fan against the wall or ceiling and mark the four screw holes and the
cable entry.
IMPORTANT: Ensure that the fan is square on wall the or ceiling.
5. Bring power cable into position, as marked. Allow an extra 230mm (9”) protruding to
facilitate connection.
Fan should only be installed by fixed wiring, a flexible cord should not be used.
6. If an XP125 kit - Select a suitable position on the outside wall for the weatherproof cowl.
Carefully remove the cowl from its housing by levering gently at the sides with a small
screwdriver. Cut a 140mm hole ensuring first that the area is free from obstruction.
7. Wiring of Standard Model XF125S and XP125S (see Diagram 2A).
(For remote switch operation).
The fan can be connected to the light switch so that the fan will start when the light is switched
on. The fan should not be accessible to a person using either the shower or the bath.
NOTE: All wiring must be fixed securely and the cable to the fan should be a minimum of
1mm2in section. All wiring must comply with current Regulations. This system should be
installed by a qualified electrician.
Pub7007 Iss06 11/17
MANROSE CLASSIC XF/XP125 CEILING/WALL
EXTRACTOR FANS
INSTALLATION INSTRUCTIONS C L A S S I C S E R I E S
Rotary adjuster
for time delay
Diagram 2B

Diagram 1
IMPORTANT
FAN MUST BE
INSTALLED THIS
WAY UP WHEN
MOUNTED ON WALL
Specifications:
Model: NZNVF120SBB; NZNVF120TBB
Electrical: 220-240V~50Hz
Fan Wattage: 25W
Max Temp: 40˚C
Airflow: 36l/s (130m3/hr)
Max Pressure: 35 Pa
Sound Volume: 41 dB(A)
IP Rated: IP44 (except pullcord model IP24)
Diagram 1A
8. Wiring of Pullcord Models XF125P and XP125P (see Diagram 1).
(This model is unsuitable for ceiling mounting).
This fan has its own integral pullcord on/off switch. The fan should not be accessible to a
person using either the shower or the bath.
NOTE: All wiring must be fixed securely and the cable to the fan should be a minimum
of 1mm2in section. All wiring must comply with current Regulations. This system should
be installed by a qualified electrician.
9. Wiring of Timer Model XF120T and XP120T
See Diagram 2 & 2A.
The fan can be connected to the light switch so that the fan will start when the light is
switched on. When the light switch or pullcord is switched off the fan will run for between
20 sec & 30 minutes (pre-set to 1 minute). The fan should not be accessible to a person
using either the shower or the bath.
Timer Adjustment XF120T & XP120T only.
T
his time delay can be adjusted by firstly switching off the power to the fan and removing the
fascia. Locate the rotary adjuster as shown in Diagram 2. The serrated adjuster wheel
can be rotated using a thumbnail to adjust the timer setting.
+ = Rotate to the right to increase the time (indicated by + on the diagram)
- = Rotate to the left to decrease the time (indicated by - on the diagram)
Only adjust with power switched off.
NOTE: All wiring must be fixed securely and the cable to the fan should be a minimum of
1mm2in section. All wiring must comply with current Regulations. This system should be
installed by a qualified electrician.
For timer adjustment see diagram 2B min 30 secs, max 30 mins.
• Isolate the mains supply before making any electrical connections.
This system should be
installed by a qualified electrician.
• Fan should only be installed by fixed wiring, a flexible cord should not be used.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.
• Precautions must be taken to avoid the back-flow of gases into the room from
the open flue of gas or other open-fire appliances when mounted in outside windows or walls.
IMPORTANT