Mantis 7268 Programming manual

MAN 430159 Rev. C 10-5-16
MODEL 7268
OPERATOR’S/PARTS MANUAL
Operator’s Manual and Safety Instructions for
Tiller/Cultivator
Tiller/Cultivator

2Operator’s Manual
IMPORTANT MESSAGE
Thank you for purchasing this Schiller Grounds Care, Inc. product. You have purchased a world class product, one of the best designed and built anywhere.
This machine comes with Operation and Safety instructions, Parts and Service instructions and Engine instructions. The useful life and good service you receive
fromthismachinedependstoalargeextentonhowwellyoureadandunderstandthesemanuals.Treatyourmachineproperly,lubricateandadjustitasinstructed,
and it will give you many years of reliable service.
Your safe use of this Schiller Grounds Care, Inc. product is one of our prime design objectives. Many safety features are built in, but we also rely on your good
sense and care to achieve accident-free operation. For best protection, study the manuals thoroughly. Learn the proper operation of all controls. Observe all
safety precautions. Follow all instructions and warnings completely. Do not remove or defeat any safety features. Make sure those who operate this machine
are as well informed and careful in its use as you are.
See a Schiller Grounds Care, Inc. dealer for any service or parts needed. Schiller Grounds Care, Inc. service ensures that you continue to receive the best
results possible from Schiller Grounds Care, Inc. products. You can trust Schiller Grounds Care, Inc. replacement parts because they are manufactured with
the same high precision and quality as the original parts.
Schiller Grounds Care, Inc. designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this machine only as
directed in the manuals, keep it in good repair and follow safety warnings and instructions. You’ll always be glad you did.
Schiller Grounds Care, Inc.
1028 Street Road
Southampton, PA 18966-4217
PHONE [phone] • FAX [phone]
SAFETY RULES & WARNINGS
Special Safety Information.................................................3
Safety & Warnings.............................................................3
Safety Decal Information...................................................3
Warning Dos......................................................................4
Warning Don’ts..................................................................5
Engine/Fuel Warning Dos..................................................5
Engine/Fuel Warning Don’ts..............................................5
ASSEMBLY ............................................................................6
Lower Handle ....................................................................7
Upper Handle Assembly....................................................8
Tines...............................................................................8-9
Kickstand...........................................................................9
FUELING & STARTING
4-Cycle Fueling & Oil Only ..............................................10
4-Cycle Corrective Action ................................................10
4-Cycle Starting Only.......................................................10
OPERATION....................................................................11-12
TRANSPORTATION.............................................................13
STORAGE............................................................................13
MAINTENANCE ..............................................................14-16
TROUBLESHOOTING .........................................................17
MANTIS TILLER ASSEMBLY & PARTS LIST .................18-19
LIMITED WARRANTY INFORMATION................BACK PAGE
TABLE OF CONTENTS
Welcome to the World of Mantis Gardening
Here’s your new MANTIS Tiller . . . the lightweight wonder that’s Changing the
Way Americans Garden.®
Unlike big tillers, your MANTIS Tiller weighs only 21 lbs. (Model 7268). So it lifts
easily, handles smoothly, tills and weeds precisely. And, unlike other small tillers,
it features serpentine tines that churn soil to ten inches deep. It creates a soft,
smooth seed bed, even in problem soil.
Once you know how to use your tiller correctly, we guarantee you’ll love it. So rst, please read this manual. It shows, step by
step, how to use your tiller safely.
ATTENTION MANTIS PRODUCT OWNERS!
Get maintenance tips for your Mantis
product on our web site
at www.mantis.com
This Operator’s / Parts Manual is part of the machine. Suppliers of both new and
second-hand machines must make sure that this manual is provided with the machine.

3Contact us at www.mantis.com
You will notice throughout this Operator’s Manual Safety Rules and Important Notes. Make sure you understand and obey these
warnings for your own protection.
I. SPECIAL SAFETY INFORMATION
II. SAFETY & WARNINGS
III. SAFETY DECAL INFORMATION
An important part of the safety system incorporated in this tiller are the warning and information decals found on various parts of
the tiller. These decals must be replaced in time due to abrasion, etc. It is your responsibility to replace these decals when they
become hard to read.
Safety Rules & Warnings
Improper use or care of this tiller or failure to wear
proper protection can result in serious injury.
Read and understand the rules for safe
operation and all instructions in this manual.
Wear hearing and eye protection.
To reduce the potential for accidents, comply
with the safety instructions in this manual.
Failure to comply may result in serious
personal injury, and/or equipment
and property damage.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Attention: This symbol points out our
important safety instructions.
When you see this symbol,
heed it’s warning!! Stay alert!!
P/N 430057
P/N 400631
Cutting hazard; keep
feet and hands away
from rotating tines.
Don’t operate
indoors
Caution: when assembling
the handles, make sure
fuel tank faces away from
operator. This is the rear of
the tiller, refer to assembly
instruction on page 8-9.
Incorrect assembly.
Wear ear
and eye
Protection.
Do not carry the
tiller in this position. Read owner’s manual before using tiller, or performing any
repair or maintenance. Keep
owners manual in a safe place.
Don’t fuel, refuel,
or check fuel while
smoking, or near an
open ame or other
ignition source.

4Operator’s Manual
If the tiller is used improperly or safety precautions
are not followed, the users risk serious injury
to themselves and others.
Read and understand this manual before
attempting to operate this tiller.
Operation of this equipment may create sparks
that can start res around dry vegetation. A spark
arrestor is installed. The operator should contact
local re agencies for laws or regulations relating
to re prevention requirements.
IV. WARNINGS - DOS
Read and understand the owner’s manual.
Pay particular attention to all sections
regarding safety.
1. Always keep a rm grip on both handles
while the tines are moving and/or the
engine is running. BE AWARE!! The
tines may coast after throttle trigger is
released. Make sure tines have come to
a complete stop and engine is off before
letting go of the tiller.
2. Always maintain a rm footing and
good balance. Do not overreach while
operating the tiller. Before you start to
use the tiller check the work area for
obstacles that might cause you to lose
your footing, balance or control of the
machine.
3. Thoroughly inspect the area where
equipment is to be used and remove
all objects, which can be thrown by the
machine.
4. Always keep area clear of children,
pets, and bystanders.
5. Always stay alert. Watch what you are
doing and use common sense. Do not
operate unit when fatigued.
6. Always dress properly. Do not wear
loose clothing or jewelry, they might
get caught in moving parts. Use sturdy
gloves. Gloves reduce the transmission
of vibration to your hands. Prolonged
exposure to vibration can cause
numbness and other ailments.
7. While working, always wear substantial
footwear and long trousers. Do not
operate the equipment when barefoot or
wearing open sandals.
8. Always wear ear and eye protection.
Eye protection must meet applicable CE
requirements. To avoid hearing damage,
we recommend hearing protection be
worn whenever using the equipment.
9. To reduce re hazard, keep the
engine, and petrol/gas storage area free
of vegetative material and excessive
grease.
10. Start the engine carefully, according to
the manufacturer’s instructions and with
feet well away from tool(s).
11.
Keep all nuts, bolts and screws tight
to be sure the equipment is in safe
working condition.
12.
Use extreme caution when reversing
or pulling the machine towards you.
13. Work only in daylight or good
articial light.
14. Always be sure of your footing on
slopes.
15. Exercise extreme caution when
changing direction on slopes.
16. Always keep a safe distance between
two or more people when working
together.
17. Always inspect your unit before each
use. Keep all knobs, nuts, bolts and
screws tight to be sure the equipment is
in safe working condition.
18. Always visually inspect to see that
the tools are not worn or damaged.
Before using your tiller, replace worn or
damaged elements and bolts in sets to
preserve balance.
19. Always maintain and examine your
Tiller with care. Follow maintenance
instructions given in manual.
20. Always store tiller in a sheltered area
(a dry place), not accessible to children.
The tiller as well as fuel should not be
stored in a house.
21. Always keep in mind that the operator
or user is responsible for accidents or
hazards occurring to other people or
their property.

5Contact us at www.mantis.com
Handle fuel with care, it is highly ammable. Fueling a hot engine or near an ignition source can
cause a re and result in serious personal injury and/or property damage.
Safety Rules & Warnings
VI. ENGINE/FUEL WARNINGS - DOS
VII. ENGINE/FUEL WARNINGS - DON’TS
Always use fresh gasoline. Stale gasoline
can cause damage.
Always store fuel in containers
specically designed for this purpose.
Always add fuel before starting
the engine.
Always replace all fuel tank and
container caps securely.
Always pull starter cord slowly until
resistance is felt to avoid kickback and
prevent arm or hand injury.
Always operate engine with spark
arrestor installed and operating properly.
Stop the engine whenever you leave
the machine and before refueling. Allow
the engine to cool before storing in any
enclosure. Replace worn or damaged
parts for safety.
If the fuel tank needs to be drained, this
should be done outdoors.
Never pick up or carry a machine while
the engine is running.
Don’t fuel, refuel or check fuel while
smoking, or near an open ame or other
ignition source. Stop engine and be sure
it is cool before refueling.
Don’t leave the engine running while the
tiller is unattended. Stop the engine when
carrying out maintenance and cleaning
operations, when changing tools and
when being transported by means other
than under its own power.
Never remove the cap of the fuel tank or
add fuel while the engine is running or
when the engine is hot.
Don’t refuel, start or run this tiller indoors
or in an improperly ventilated area.
Don’t run engine when electrical system
causes spark outside the cylinder. During
periodical checks of the spark plug, keep
plug a safe distance from cylinder to
avoid burning of evaporated fuel from
cylinder.
Don’t check for spark with spark plug
or plug wire removed. Use an approved
tester.
Don’t crank engine with spark plug
removed unless spark plug wire is
disconnected. Sparks can ignite fumes.
Don’t run engine when the odor of gasoline
is present or other explosive conditions exist.
Do not attempt to start the engine if
fuel is spilled, but move the machine
away from the area of spillage and avoid
creating any source of ignition until fuel
vapors have dissipated.
Don’t operate your tiller if there is an
accumulation of debris around the
mufer, and cooling ns. To reduce the
re hazard, keep the engine and fuel
storage area free of vegetative material
and excessive grease.
Don’t touch hot mufers, cylinders
or cooling ns as contact may cause
serious burns.
Don’t change the engine governor
setting or over speed the engine.
Don’t attempt to remove spark plug while
engine is hot. Removing a spark plug
from a hot engine can cause irreparable
damage to the engine and will void your
warranty.
Don’t use starter uids as they will cause
permanent engine damage.
V. WARNINGS - DON’TS
Don’t use tiller with one hand. Keep
both hands on handles with ngers and
thumbs encircling the handles, while
tines are moving, and engine
is running.
Don’t run with the machine, walk.
Don’t work on excessively steep slopes.
Don’t attempt to clear tines while they
are moving. Never try to remove jammed
material before switching the engine off
and making sure the tines have stopped
completely.
Don’t allow children or people unfamiliar
with these instructions to use the
machine. Local regulations can restrict
the age of operator.
Don’t let others operate tiller without
proper training.
Don’t operate while under the inuence
of alcohol or drugs.
Don’t attempt to repair this tiller. Have
repairs made by a qualied dealer or
repairman. See that only original Mantis
parts are used.
Don’t overreach. Keep a good footing at
all times.
Don’t stand in front of tiller when tines
are rotating.

6Operator’s Manual
Assembly
WHAT COMES IN THE BOX
WHAT YOU WILL NEED
TO ASSEMBLE THE TILLER
Prior to removing the contents and assembling, it is
important to:
• Have a clean work area.
• Make sure all necessary tools are handy.
• You will need two 7/16” wrenches. (Power tools may
be required)
Improper assembly of this tiller can result in serious injury. Make
sure to follow all instructions carefully. If you have any questions,
contact our factory at 1-800-366-6268 or an authorized Mantis dealer.
Key Qty. Part No. Description
T1 1 Upper Handle Throttle SideAssembly
T2 1 Upper Handle Assembly, Left
T3 2 Lower Handles W/Plug
T4 1 Handle Brace Assembly
T10 1 Plastic Carrying Handle
T21, T20,
T46 1 Engine Assembly (includes Fender Guard & Worm Gear Transmission)
T39/T40 1 Pair Tiller/Cultivator Tines
1 Bag of Hardware
T7 2 Handle Clamps
T9 1 Throttle Clip
T11 2 Bolts (3” long)
T12 2 Knobs
T14 4 Lock Nuts
T15 2 Cap Screws
T41 2 Tine Retaining Pins
T42 2 Carriage Bolts
Not
Shown 1 4-Cycle Oil
Picture of Model 7268
T40
T41
T4
T10
T15
T39
T1
T3
T20
T46
T21
T2
T12
T9
T7
T11
T42 T14
Bag Contents
T41
T15
T12
T7
T9
T11
T14
T42

7Contact us at www.mantis.com
LET’S BEGIN
• With the box upright, open the box and remove the
tine box and the loose parts that are at the top of the
tiller box. Do not remove any other parts in the box.
• Lay the box on one side and open the bottom aps.
• Return the box to an upright position (as shown) and
pull the box straight up.
• Leave the engine and throttle handle in the cradle to
assist in the assembly.
• Lay everything out so you can easily identify the
parts (see parts image and list on page 6).
Assembly
• Take the lower handles that
you’ve just put together.
Slide them into the two
recessed channels.
• Make sure you insert them
from the rear of the tiller
(gasoline tank faces away
from the operator)... so
that the bolt ts along the
back of the housing.
• Slide the second 3-inch
bolt (T11)through the
second set of holes in
the short legs. Add a
lock
nut (T14)
and tighten
nger tight until you’ve
completed assembly.
LOWER HANDLE ASSEMBLY
• For ease of assembly and
stability it is important that you
keep the engine assembly in its
cardboard cradle.
1
6
• Lay the handle parts within easy
reach. You’ll need one of the
handle clamps (T7) and one of
the lower handles (T3). Note that
the lower handles have a short
leg on one end.
• Fit the handle clamp along the
outside of the short leg. Line
up the holes on the clamp and
the leg.
2
• Choose one of the two 3-inch
bolts (T11). Slide it through the
rst set of holes — near the
elbow where the lower handle
curves. (Pictures 2 & 3)
• Now slide the other lower
handle onto the 3-inch bolt. Fit
the other
clamp onto the other
handle’s short leg.Add a lock
nut (T14) and tighten nger tight.
(Picture 3)
3
• Locate recessed channels
below the engine.
4
5
NOTE: THE LOCK NUTS ARE STAMPED. FINGER TIGHT ISAPPROXIMATELY 1/2 TO 1-1/2 TURNS UNTILYOU’VE COMPLETED ASSEMBLY.
To identify part numbers see page 6.
NOTE: Some of the photos in this manual do not represent your
tiller engine. They are for assembly purposes only.

8Operator’s Manual
Assembly (Continued)
UPPER HANDLE ASSEMBLY
• You’ll need the 2 Tines and the
2 retaining pins. • Remove the unit from the
cardboard cradle and lay the
unit on its side.
• You will notice that one side of the
Tine has a circular hole while the
other has a “D” shaped hole.
TINE ASSEMBLY
1 2 3
8
• Lift the upper handle until it lines up
with the lower handle.
• Insert carriage bold (T42) from outside in.
• Screw on knob (T12) and fully tighten
the knob at the pivot point.
• Follow the same steps to install the
other upper handle onto the other
lower handle.
• Use the clip (T9) to secure the throttle
cable and wire in place on the lower
handle.
• Now install the handle brace. Line it up with
the holes on the upper handles. Then insert a
cap screw (T15) and a lock nut (T14) on either
side.
• Use a wrench to tighten cap screws and lock
nuts.
• Now use wrench to tighten all nuts and bolts
rmly and securely. (Power tools may be
required)
10
9
• Lightly squeeze the lower
handles (T3) toward one another
so that they line up with the two
smaller holes on the carrying
handle (T10). Then slide the
carrying handle over and down
the lower handles. It will rest
about four to six inches above the
fender.
• Gently pull the lower handles out
to their original position.
• Your Mantis Tiller will look like
this when the lower handle
assembly is complete.
7a 7b

9Contact us at www.mantis.com
Assembly (Continued)
• Attach the Tine so that the circular hole
slides onto the axle rst.
• When the axle protrudes from the
other side it will line up perfectly
with the “D” shaped hole.
4 5
IMPORTANT NOTE:
Be sure you have proper throttle movements and that
the throttle cable is not wrapped or twisted around the
handle bar. Hold the lockout button, fully squeeze the
throttle trigger and let go. The throttle triangle must
click in both directions. If there is any doubt, remove
air lter and visually check that the throttle triangle hits
both the idle screw and the full open stop. THIS MUST
BE DONE BEFORE STARTING THE ENGINE.
IMPORTANT NOTE:
Before you use your MANTIS Tiller, read the
Safety Rules & Warnings on pages 3-5
IMPORTANT NOTE:
Make sure you have installed the handles properly.
When you stand behind your tiller, holding the handles,
the fender warning label should face you.
Improper Throttle installation can cause tines to rotate unexpectedly.
7268
TINE ASSEMBLY (Continued)
• Slide a retaining pin (T41) through
the hole in the axle to secure the
Tine.
• Repeat steps for the other side.
6

10 Operator’s Manual
Fuel is extremely ammable. Handle it with
care. Keep away from ignition sources. Do not
smoke while fueling your equipment
Do not operate the engine in a conned
space where dangerous carbon monoxide
fumes can collect.
Avoid accidental blade engagement.
Do not squeeze the throttle trigger when starting. Main-
tain proper idle speed adjustment (2500-3100 rpm)
WARNING • DANGER
ALTERNATIVE FUELS, SUCH AS E-15 (20% ETHANOL), E-85 (85% ETHANOL)
OR ANY FUELS NOT MEETING HONDA REQUIREMENTS ARE NOT APPROVED
FOR USE IN GASOLINE ENGINES. USE OF ALTERNATIVE FUELS MAY CAUSE
PERFORMANCE PROBLEMS, LOSS OF POWER, OVERHEATING, FUEL VAPOR
LOCK AND UNINTENDED MACHINE OPERATION, INCLUDING, BUT NOT LIMITED
TO, IMPROPER CLUTCH ENGAGEMENT. ALTERNATIVE FUELS MAY ALSO CAUSE
PREMATURE DETERIORATION OF FUEL LINES, GASKETS, CARBURETORS AND
OTHER ENGINE COMPONENTS.
! !
4-Cycle Tiller Fueling & Starting
4-CYCLE TILLER FUELING AND OIL ONLY
• Rock the tiller forward so that it
rests on the fuel tank.
• It is important to position the
Mantis 4-Cycle Tiller as shown in
Figure 1 so the oil will properly
ll the crankcase. Failure to do so
will cause engine damage.
• Remove the oil plug.
• Pour in 2.7 . oz. of approved,
4-cycle engine oil.
• Always check the oil level before each use. The oil level should
reach the inner rst thread of the reservoir. Do not overll.
• Replace the oil plug.
• Then return the unit to the upright position and put the kickstand
down.
Fueling your Mantis 4-Cycle Tiller/Cultivator is easy. Unscrew the gas
cap and ll the tank about four-fths of the way up with 89 octane
unleaded gasoline. And remember, always drain the gas when
transporting the unit from one location to another.
4-CYCLE TILLER STARTING ONLY
Starting the engine for the rst time, or “cold
starting”, is easy.
• First, make sure the start/stop switch, located on
the throttle handle, is in the start position, which
is indicated by the “I” symbol.
• Close the choke by moving the choke lever to the
up position.
• Press the primer bulb approximately 6 times until he bulb is lled
with gas. Once it is lled, press it two more times.
• Pull the starter cord lightly until you feel resistance and then give it
a short, brisk pull. Your tiller should start immediately. Do not pull
the cord all the way out and do not let it snap back into the starter
housing.
•
Once it is running, open the choke. Ensure the lever is fully down
• To stop the engine, simply push the start/stop switch to the
stop position “O.”
• To start a warm engine, follow the same procedure. Except now you
can leave the choke lever in the down position and there is no need
to pump the primer bulb.
• Before using the tiller, let the engine run for a minute to warm up.
And before shutting it down, let the engine run briey to
cool down.
OFF ON
Switch
IMPORTANT NOTE:
Check the oil level in the
engine before each use. If
oil is low see your 4 Stroke
Tiller Engine Manual and
information above for
details.
Never use starting uids as
they will cause permanent
engine damage. Using them
will void the warranty. Before
you use the tiller, read the
Safety & Warning rules on
pages 3-5.
IMPORTANT!
It is normal for your 4 stroke engine to smoke for the rst
minute or two of operation, however it is not necessary
for this to occur every time. This is a result of the oil being
pulled through the engine for lubrication.
Figure 1

11Contact us at www.mantis.com
4-Cycle Tiller Operation
Read the instructions carefully. Be
familiar with the controls and the
proper use of the equipment.
A SPECIAL FEATURE
(With the idle set properly and the engine
running)
Even when the engine is running, the
tines won’t turn unless you squeeze the
throttle trigger on the handlebars. When
you release the throttle trigger, the tines
will stop
.
A TIP FOR EXTENDING
YOUR ENGINE’S LIFE
After you start the engine, let your tiller
warm up for two to three minutes before
you use it. Then, before you put your
tiller away, let it idle for a minute to give
the engine a chance to cool down.
OPERATION
With engine running, and both hands
on the handles, hold down the throttle
lockout trigger (Figure 1), then squeeze
the throttle trigger gradually to increase
the engine speed and engage the tines.
NOTE: This step must be repeated each
time your tiller trigger is released.
NOW YOU’RE READY TO USE
YOUR MANTIS TILLER.
If you’ve seen other tillers, your MANTIS
Tiller may surprise you. It tills best when
you pull it backward! You see, when you pull
your MANTIS Tiller backward, you give extra
resistance to the tines, so they dig deeper.
(Figure 2)
In addition, when you go backward, you erase
your footprints. So your soil stays light and
uffy. With other tillers, by contrast, you walk
right over the soil you’ve just tilled, packing it
down, so it’s less plantable.
RUN YOUR MANTIS TILLER
LIKE A VACUUM CLEANER
Place your Tiller at the head of the row or
area you want to till. Start it up. Then use
an easy rocking motion. First, pull your Tiller
backward. Then use an easy rocking motion.
Again, pull your Tiller backward. Then, let
it move forward just a little bit. Then pull it
backward again. This will help you till deeper.
Keep repeating these steps until you’ve tilled
an entire row. Start again on the next row. It’s
much like running a vacuum cleaner! (Figure 3)
You Can Even Control Depth.
For Deeper Tilling:
Move your Tiller slowly back and forth, as you
would a vacuum cleaner. Work the same area
over and over until you’ve dug to your desired
depth. (Figure 4)
For Shallow Tilling:
Switch the tines to the cultivating position.
(See page 12 to learn how.) Then move your
Tiller quickly over your soil surface.
For Big Weeds or Tough Roots:
Let your Tiller rock back and forth over the
tough spot, until the tines slice through the
weed or root.
Your MANTIS Tiller Handles Special Tilling
Projects:
Want to turn part of your lawn into a colorful
ower border? Your MANTIS Tiller makes it
easy! Just run your Tiller back and forth until
the sod begins to break up. Then continue
tilling. Your Tiller will chop the clumps of sod
until they’re ne. Then, it will work them into
the soil. Pretty soon, you’ll have a soft, fresh
planting bed.
Figure 2 Figure 3 Figure 4
WARNING
ALWAYS MAKE SURE THE HANDLE KNOBS ARE
SECURE BEFORE STARTING YOUR MANTIS TILLER.
! !
If engine does not stop when switch is put in the stop
position, release the throttle, allow engine to idle. Put
the tiller down, and slide the choke lever to the cold start
(closed) position. Have product serviced before using.
Figure 1

12 Operator’s Manual
YOUR MANTIS TILLER MAKES
WEEDING A PLEASURE!
As a tiller, your MANTIS Tiller works the soil
down to 10” (25.4 cm) deep. But, as a cultivator,
it gently cultivates the surface, only 2” to 3” (5.09
cm to 7.62 cm) deep.
First, you must switch the tines to the weeding,
cultivating position. This takes less than a
minute.
Then, your MANTIS Tiller’s sharp “tine teeth” will
slice up those pesky weeds, burying them as you
go along. And, since the tines in this position
won’t dig too deep, they won’t hurt your plants’
precious root systems.
The result? Your Tiller will cut your weeding time
in half, and turn a tiresome chore into a pleasure.
HOW TO SWITCH FROM TILLING TO
CULTIVATING POSITION
1. Make sure your Tiller is off.
2. Remove the retaining pins from the tines.
3. Remove the tines from the axle.
4. Place the right-side tine onto the left-side axle.
Place the left side tine onto the right-side axle.
The “D” hole should be to the outside.
5. Reinsert the pins. (Figure 1)
4-Cycle Tiller Operation (Continued)
The operator of this tiller is responsible for
accidents or hazards occurring to himself, oth-
er people or their property.
If your tines get jammed or entangled, shut off the
engine at once. Remove the obstruction while the
engine is off. Never try to remove an obstruction while
the engine is running. Serious injury can result.
To set them for tilling, attach the tines
so the points of the blades face forward
- away from the operator. The tines’
points will contact the ground rst.
For cultivating, reverse the tines
so that the points of the tines face
backward - toward the operator. Now
the long at part of the tine’s blade
will contact the ground rst.
Tilling Cultivating
Figure 1

13Contact us at www.mantis.com
Each fall, or before you store your
Mantis Tiller for any long period, be sure
to take these measures:
1. Do not store your Tiller with fuel still in
it. Even under ideal conditions, stored
fuel containing ethanol or MTBE can
start to go stale in 30 days. And, since
stale fuel has a high gum content, it
can clog the carburetor, this, in turn,
will restrict fuel ow. Therefore, when
you’re ready to store your Tiller, or will
not be using it for more than 2 weeks,
drain the fuel tank completely.
2. Next, restart the engine to make
sure no fuel is left in the carburetor.
Then, run the engine until it stops.
This will prevent gum deposits,
forming inside of the carburetor and
possible engine damage.
3. Disconnect spark plug wire and
remove the spark plug. Slowly pull the
starter cord once.
4. Inspect the spark plug, and if
necessary, clean it. If you need to
replace it, buy a NGK-CMR5H.
5. Install the spark plug, but leave the
spark plug wire disconnected.
6. Wipe the tines with oil or spray them
with WD-40, to prevent rusting.
7. Clean or replace the air lter.
8. Check or replace fuel lter.
9. Check the grease level in the worm
gear housing. Add grease if needed.
10.Store your Tiller in an upright position
in a clean, dry place. You can store
with the handles in an extended
position or folded down.
To fold the handles down, simply
loosen the lower 2-pronged knobs
until you can pivot the upper handles
down. (Figure 3)
Or it can be hung using the handle
brace.
11.Do you have fuel left over from last
season? Dispose of it properly. Buy
fresh oil and gasoline next season.
12.Remove Tilling Tines or attachments
and lightly oil tine shaft at least once
a year.
4-Cycle Tiller Transportation & Storage
Never store the equipment
with fuel in the tank or in
an area where fumes may
accumulate and breach an
open ame or spark
4-CYCLE TILLER TRANSPORTATION
Transporting your Tiller is easy. It’s light enough and easy to carry
using the carrying handle as seen in Figure 1.
Or, with it running, you can walk it by gently squeezing the
throttle until it moves at a comfortable pace.
Your tiller is easily transported in the back of a car or truck. Be
sure to empty the fuel tank (This is crucial)! Then stow your tiller
in the trunk of your car or truck.
TILLER STORAGE
Figure 3
Figure 2
WARNING
NEVER CARRY YOUR TILLER AS THE PERSON IN
FIGURE 2 IS DOING. IF YOU DO, YOU WILL SUFFER
SERIOUS INJURY.
! !
IMPORTANT:
It is important to store your 4-Cycle
Mantis Tiller in an upright position.
Laying the Tiller on its side will
cause the oil to leak out of the engine
through the air cleaner case.
IMPORTANT:
Avoid any orientation that places the
top cover (engine head) down -this
may allow oil from the crankcase to
enter the combustion chamber and
cause hard starting or a locked piston.
Figure 1

14 Operator’s Manual
4-Cycle Tiller Maintenance
Air Filter
Dipstick
Your 4 Cycle Tiller will require some basic maintenance
to keep it performing year after year.
If you are storing your tiller for the season or longer than
30 days it is very important to empty the fuel tank to
prevent engine damage.
Undoubtedly, you will be putting your tiller through
rigorous use.
Check engine oil level, air lter and fuel lter.
Refer to your Honda®engine manual for more details.
Fuel Filter
If you suspect the engine is overlled the following procedure should
remove the excess oil from the crankcase and valve cover.
If the engine is overlled, oil will enter the crankcase and it does not
simply pour out of the oil ll opening. The excessive oil has to be
pumped out as the engine runs. Checking the oil level and draining any
excess between multiple 30 second running intervals will bring the oil
back to the proper level.
1. Place the engine on a level surface resting at on the fuel tank and
remove the oil ll cap/dipstick. Use a catch basin for any oil that
overows from the oil ll opening.
2. Replace the oil ll cap/dipstick and run the engine for approximately
30 seconds then repeat step one. Continue steps 1 & 2 until oil no
longer overows when the oil ll cap/dipstick is removed.
3. Once the oil level is corrected the engine may continue to smoke
while running for several minutes while the residual oil burns off.
4-CYCLE PROPER OIL FILL/
LEVEL CHECK POSITION
Engine must be resting on a at surface on the
fuel tank
This position does
not allow for a
proper oil level
reading and may
cause overlling.
4-CYCLE CORRECTIVE ACTION

15Contact us at www.mantis.com
4-Cycle Tiller Maintenance (Continued)
A wet or dirty air lter can affect the way your engine starts, performs, and wears.
So, it’s a good idea to check your air lter once a month.
If you work in dusty soil, or if you want to be on the safe side — check your lter
more often (for instance, before each use). But be sure to replace it at least once a
year, in the spring or fall.
How to Check, Clean and Change the Air Filter
AIR FILTER MAINTENANCE
Figure 1 Figure 2
1. The air lter is held in the air cleaner in a black housing on the side of the tiller,
behind the gas tank cap.
2. Squeeze the two locking tabs at the rear of the air cleaner cover (Figure 1) and
swing the cover towards the front of the engine to open it
3. The air lter is the dark sponge like material on the inside of the air cleaner.
Check whether it is soiled or moist.
4. If the air lter needs to be cleaned or no longer ts properly, simply remove it by
carefully peeling it out of the air cleaner. (Figure 2)
5. To clean the air lter
a. Clean the lter element in warm soapy water, rinse and allow to dry
thoroughly. Or, clean in a non-ammable solvent and allow to dry.
b. Dip the lter element in clean engine oil, then squeeze out all excess oil. The
engine will smoke when started if too much oil is left in the element.
c. Wipe dirt from the air cleaner body and cover, using a moist rag. Be careful to
prevent dirt from entering the carburetor.
6. Insert your clean lter inside the air cleaner.
IMPORTANT:
Make sure the lter is “seated”
properly in the cover. The lter
must t snugly inside the open-
ing that holds the lter in place.
Installing the lter incorrectly will
cause engine damage and void
the warranty. Fit the cover back
over the air cleaner and snap the
two locking tabs
IMPORTANT NOTE:
A dirty air cleaner will restrict air
ow to the carburetor, reducing
engine performance. If you oper-
ate the engine in very dusty areas,
clean the air lter element more
often then specied in the
Maintenance section.
IMPORTANT NOTE:
Operating the engine without an
air lter element, or with a dam-
aged air lter element, will allow
dirt to enter the engine, causing
rapid engine wear. This type of
damage is not covered by the
Limited Warranty
IMPORTANT NOTE:
Please check the lip on the Air
Cleaner Cover. If the lip is chipped
or cracked, it should be replaced.
This will prevent dirt from being
ingested through the carburetor
into the inside of the engine.

16 Operator’s Manual
Check the transmission grease level after the rst
10 hours of use, then check yearly.
With the tines off, remove the transmission plate
(Figure 3) and gasket to see if the grease level is up
to the plate ange (Figure 4). If it is not, you will need
to add lithium zero or lithium one grease.
Wipe off any excess grease, replace the transmission
gasket and plate.
At some point, you may nd that the
tines won’t turn when you press the
throttle. This may mean the engine isn’t
sitting all the way down on the worm
gear housing.
Perhaps you’ve been using your Tiller
for several years. Or perhaps you’ve
removed the engine for use with our
hedge trimmer attachment, then replaced
it. In either case, the ange bolt may
have come loose and lifted the
engine up.
If this happened you’ll notice a gap
between the bottom of the engine clutch
case and the top of the worm gear
housing. (Figure 1)
To x this, loosen the ange bolt. Take
the engine off the worm gear housing.
Notice the hex head on top of the drive
shaft . Inside the clutch case, you’ll nd
the clutch drum. Make sure the hex head
lines up with the clutch drum inside the
clutch case.
Then put the engine back on the
worm gear housing. Make sure the
plastic carrying handle is not under the
fuel tank.
If you’ve followed these steps properly,
there will be no gap between the clutch
case and the worm gear housing.
(Figure 2) Make sure you tighten the
ange bolt!
All other engine maintenance issues can
be found in the Honda®Engine Manual
included in your tiller package.
Note how the engine doesn’t sit all
the way down on the transmission.
HOW TO RESEAT THE FLANGE
TRANSMISSION CARE
Note how the engine sits all the
way down on the transmission.
4-Cycle Tiller Maintenance (Continued)
Figure 3
Figure 4
Figure 1 Figure 2
Gap No Gap

17Contact us at www.mantis.com
Troubleshooting
Problem Cause Remedy
1. Tines don’t turn when throttle
is depressed • Engine is not seated properly on the gear housing. • Re-install engine following the instructions on page 16 “How to reseat the flange”.
2. Engine fails to start • O/I switch is in “O” position.
• No fuel in tank.
• Fuel strainer clogged.
• Fuel line clogged.
• Spark plug shorted or fouled.
• Spark plug is broken (cracked porcelain or
electrodes broken)
• Ignition lead wire shorted, broken or disconnected from
spark plug.
• Ignition inoperative
• Move switch to “I”
• Fill Tank.
• Replace Strainer.
• Clean fuel line.
• Install new spark plug.
• Replace spark plug.
• Replace lead wire or attach to spark plug.
• Contact your local authorized dealer.
3. Engine hard to start. • Water in gasoline.
• Gasket leaks (carburetor or cylinder base gasket).
• Weak spark at spark plug.
• Drain entire system and refill with fresh fuel.
• Replace gaskets.
• Contact your local authorized dealer.
4. There is black smoke coming from
exhaust • The muffler screen is clogged • Clean carbon from muffler screen. See engine manual.
5. Engine misses. • Dirt in fuel line or carburetor.
• Carburetor improperly adjusted.
• Spark plug fouled, broken or incorrect
gap setting.
• Weak or intermittent spark at spark plug.
• Remove and clean.
• See “Carburetor Adjustment” in engine manual.
• Clean or replace spark plug - set
gap to .024-.028
in. (0.6-0.7 mm)
• Contact your local authorized dealer.
6. Engine lacks power. • Air filter clogged.
• Muffler clogged.
• Spark Arrestor Clogged.
• Poor compression.
• Clean or replace air filter (page 15).
• Clean carbon from muffler, see engine manual.
• Clean Spark Arrestor, see engine manual.
• Contact your local authorized dealer.
7. Engine overheats. • Air flow obstructed • Clean flywheel cylinder fins and screen.
See engine manual.
8. Engine noisy or knocking. • Spark plug in incorrect heat range.
• Bearings, piston ring or cylinder walls are worn.
• Replace with plugs specified for engine.
• Contact your local authorized dealer.
9. Engine stalls under load. • Engine overheats. • Remove dust and dirt from between fins.

18 Operator’s Manual
4-Cycle Tiller Assembly
21
47
50
51
49
48
T16
T17
37
T36
Model #7268 ___ 4-CYCLE TILLER
T38
T34
EXPLODED VIEW
T44
T46
T38
T37
T36 T33
31
T30 T29
T45
T32
T28
T27
T24
T25 T26
T35
T35
T23
T20
T39
T41
T3
T22*
T42 T18
T8
T9
T9
T4
T2 T1
Rev. A, 07/28/2016
T41
T40
T43
T11
T15
T42
T7
T7
T14
T10 T12
T12
T14
T14 T15

19Contact us at www.mantis.com
Key Qty. Part No. Description T1 1 430168 Trigger Handle Assembly, 4 Cycle Engine, Right T2 1430161 Handle Assembly, Left T3 2430082 Lower Handle W/Plug T4 1430163 Handle Brace Assembly T7 2377 Handle Clamp T8 24078 M6 Jam Nut T9 2478 Throttle Clip T10 1400315 Carry Handle T11 2470 Bolt 1/4-20 X 3” T12 2400523 Knob, Two Prongs, Female T14 4972 1/4-20 Two-Way Lock Nut T15 2 144-2 1/4-20 X 1.125 Hex Head Cap Screw T16 2140 Bolt 1/4-20 X 3/8” Long T17 1430058 Mantis Logo Label T18 24079 M6 Internal Lock Washer T20 1465 Fender Guard T21 1400911 Engine Assembly-25Cc Honda1 T22* 1468 Drive Shaft T23 1466 Worm Gear Housing T24 1436 Gasket T25 1437A Gear Housing Cover T26 4651 #8 Self Tapping Screw T27 1423 Roller Bearing T28 2425 Worm Bearing Race
Key Qty. Part No. Description T29 1424 Worm Thrust Bearing T30 1422 Worm Shaft T31 1 426 Worm Disk T32 1 428 Retaining Ring T33 1429 Worm Gear T34 1431 Tine Shaft T35 2430 Worm Gear Thrust Washer T36 2432 Worm Gear Bearing T37 2434 Bearing Seal T38 2435 Bearing Seal Retainer T39 1438RA Tine Assembly, Right T40 1438LA Tine Assembly, Left T41 2418-1 Tine Retaining Pin T42 2400509 Carriage Bolt 1/4-20 X 2.25” T43 1430043 Ground Wire Jumper, 4 Cycle Engine T44 1400631 Triangle Warning Label (4 Cycly Engine) T45 1458 Roller Bearing T46 1400010 Transmission Assembly T47 1 400131 Clutch Drum
T48 1 400132 Bearing T49 1400130 Engine Flange
T50 4400511 M6 X 12 Flange Bolt T51 1 910502 10-32 X 3/4” Flange Bolt
*Also in key T46
Parts List

MANTIS extends this limited warranty against defects in material and workmanship for a period of ve (5) years under normal
usage for residential purposes and two (2) years under normal usage for commercial purposes, from the date of purchase by
the original purchaser.
MANTIS will repair or replace, at its option, any part or parts of the product found to be defective in material or workmanship
during the warranty period. Warranty repairs and replacements will be made without charge for parts or labor. All parts replaced
under warranty will be considered as part of the original product, and any warranty on the replaced parts will expire coincident
with the original product warranty. If you think your MANTIS TILLER is defective in material or workmanship, please contact
customer service at 800-366-6268 for the location of an authorized servicing dealer or send it, along with your proof of purchase
(sales receipt) to:
Mantis
1028 Street Road
Southampton, PA 18966
You are responsible for pickup and delivery charges; if shipping to factory the product must be returned to us postage paid.
Engines are warranted separately by the engine manufacturer
MANTIS assumes no responsibility in the event that the product was not assembled or used in compliance with any assembly,
care, safety, or operating instructions contained in the Operators Manual or accompanying the product. This limited warranty
does not cover damages or defects due to normal wear and tear, lack of reasonable and proper maintenance, failure to follow
operatinginstructionsoroperatorsmanual,misuse,lackofproperstorageoraccidents.This limited warranty shall not be effective
if your Mantis tiller has been subjected to negligence or has been repaired or altered by anyone other than an authorized dealer
or authorized service center.
You must maintain your MANTIS TILLER by following the maintenance procedures described in the operators manual. Such
routine maintenance, whether performed by you or a dealer, is at your expense.
MANTIS MAKES NO EXPRESS OR IMPLIED WARRANTIES, REPRESENTATIONS OR PROMISES EXCEPT THOSE
CONTAINED HEREIN. THERE ARE NO OTHER WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESSFORAPARTICULARPURPOSE.ALLWARRANTIESOTHERTHANTHEEXPRESSWARRANTYSETFORTHABOVE
ARE SPECIFICALLY DISCLAIMED. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND
FITNESSFORAPARTICULARPURPOSE,ISLIMITEDTOTHEDURATIONOFTHISWRITTENLIMITEDWARRANTY.MANTIS
DISCLAIMS ALL LIABILITY FOR INDIRECT, INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH
THE USE OF THE MANTIS PRODUCTS COVERED BYTHIS WARRANTY. SOME STATES DO NOTALLOW LIMITATIONS ON
HOW LONGAN IMPLIED WARRANTY LASTS AND/OR DO NOTALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THAT ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATES TO STATE.
MANTIS
1028 Street Road
Southampton, PA 18966
[phone]
©2016 Schiller Grounds Care, Inc. All Rights Reserved.
LIMITED WARRANTY
Specications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are
subject to change without notice.