Marmitek DS90 User manual

D
S9
0
DS90™
DOOR/WINDOW SENSOR
20540/20120530 • DS90
ALL RIGHTS RESERVED MARMITEK©
USER MANUAL

2© MARMITEK

USER MANUAL DOOR/WINDOW SENSOR DS90 (Art.
no. 09583)
SAFETY WARNINGS
• In case of improper usage or if you have altered and
repaired the product yourself, all guarantees expire.
Marmitek does not accept responsibility in the case of
improper usage of the product or when the product is used
for purposes other than specified. Marmitek
does not accept responsibility for additional damage other
than covered by the legal product responsibility.
• Batteries: keep batteries out of the reach of children.
Dispose of batteries as chemical waste.
Never use old and new batteries or different types of
batteries together. Remove the batteries when you are not
using the system for a longer period of time. Check the
polarity (+/-) of the batteries when inserting them in the
product. Wrong positioning can cause an explosion.
3DS90

DOOR/WINDOW SENSOR DS90
1. Transmitter part.
2. Magnet contact.
3. Control Indicator - Lights up when a signal is
transmitted.
4. Screw for opening the sensor.
5. Switch for entry delays.
6. Connection for extra wired contact.
7. Battery compartment.
8. Screw holes for mounting the sensor.
9. Tamper contact.
4© MARMITEK
12
3
4
5
7
8
8
6
9

5DS90
USING THE DOOR/WINDOW SENSOR
1. Open the casing by removing screw (4).
2. Insert the batteries (2xAAA, alkaline) into the battery
compartment. Do not forget to check the polarity.
3. Set the switch for entry delay (5) to MIN when you have
installed the sensor on a window and on MAX when the
sensor is installed on a door. When the switch is set to
MAX, you have time to open and close the door without
triggering the alarm. If you want an instant alarm (on e.g.
the backdoor), set the switch to MIN.
4. Keep the tamper contact (9) on the transmitter pressed for
4 seconds. Release the button. The door/window sensor
has now chosen a unique code, which can be registered
with your console.
REGISTER THE DS90 DOOR/WINDOW SENSOR
You need to register the DS90 door/window sensor with
your TotalGuard/SafeGuard/Protector system. Your system’s
user guide will show you how to do this. If you do not have
a user guide at hand, you can download one from
www.marmitek.com (customer service -> manuals).

ADDING A WIRED SENSOR TO THE DOOR/WINDOW
SENSOR DS90
The DS90 Door/Window Sensor has a contact for an extra
wired sensor. These sensors need to be of type NC (normally
closed contacts). There should not be any power on this
contact (potential-free).
1. Open the transmitter part of the DS90 by removing the
screw.
2. Remove the wire bridge from the connection for the wired
sensor (6).
3. Connect your sensor.
The wired contact has its own zone on the console. You can
register the contact using the procedure as described in your
manual. To register the sensor, trigger the alarm of your
wired sensor while registering it.
 The setting of the MIN/MAX switch (entry delay) of the
DS90 is valid for both the magnetic contact and the wired
sensor.
TECHNICAL DATA
Power 2x AAA battery
Range Up to 100m free field, up to 30m through
walls and ceilings
Dimensions 44x86x20mm
Frequency 433.92 MHz
6© MARMITEK

DS90
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product
and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates
that this product should be disposed of separately from regular household waste streams. It is your
responsibility to dispose of this and other electric and electronic equipment via designated collection
facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential
negative consequences to the environment and human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities, waste disposal service, or the shop where you
purchased the product.
DECLARATION OF CONFORMITY
Hereby, Marmitek BV, declares that this DS90 is in compliance with the essential
requirements and other relevant provisions of the following Directives:
Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on
radio equipment and telecommunications terminal equipment and the mutual recognition
of their conformity
Directive 2004/108/EC of the European Parliament and of the Council of 15 December
2004 on the approximation of the laws of the Member States relating to electromagnetic
compatibility
Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the
restriction of the use of certain hazardous substances in electrical and electronic equipment
COPYRIGHTS
Marmitek is a trademark of Pattitude B.V.
DS90™ is a trademark of Marmitek B.V. All rights reserved.
Every effort has been made to ensure that the information in this manual is accurate.
Marmitek is not responsible for printing or clerical errors.
Copyright and all other proprietary rights in the content (including but not limited to model
numbers, software, audio, video, text and photographs) rests with Marmitek B.V. Any use of
the Content, but without limitation, distribution, reproduction, modification, display or
transmission without the prior written consent of Marmitek is strictly prohibited. All
copyright and other proprietary notices shall be retained on all reproductions.
Other company and product names mentioned herein may be trademarks of their respective
companies. Mention of third-party products is for informational purposes only and
constitutes neither an endorsement nor a recommendation. Marmitek assumes no
responsibility with regard to the performance or use of these products.
MARMITEK BV - P.O. BOX 4257 - 5604 EG EINDHOVEN – THE NETHERLANDS
0165