Marmitek M229 User manual

20089 / 20070329 • M229TM
© ALL RIGHTS RESERVED MARMITEK®2007
MARMITEK M229
DOORPHONE
SYSTEM
OWNER’S MANUAL 2
BETRIEBSANLEITUNG 18
NOTICE D’UTILISATION 34
GEBRUIKSAANWIJZING 50
• 2 WIRE SYSTEM
• BUILT-IN MEMORY (32 PICTURES)
WITH TIME AND DATE RECORDING
• UP TO 8 MONITOR STATIONS
• CONNECT UP TO 4 DOORCAMERAS AND
A MAXIMUM OF 3 DOME CAMERAS

ENGLISH
2© MARMITEK
SAFETY WARNING
• This product is for professional use and should be installed by a certified installer.
• To prevent short circuits, this product (except the EX229D door unit) should only be used inside and
only in dry spaces. Do not expose the components to rain or humidity. Do not use the product close to
a bath, swimming pool etc.
• Only connect the adapter to the mains after checking whether the mains voltage is the same as the
values on the identification tags. Never connect an adapter or power cord when it is damaged. In that
case, contact your supplier.
• Do not expose the components of your systems to extremely high temperatures or bright light sources.
• Do not open the product: the device contains live parts. The product should only be repaired or
serviced by a qualified repairman.
• Do not open the product: the device contains live parts. The product should only be repaired or
serviced by a qualified repairman. In case of improper usage or if you have opened, altered and
repaired the product yourself, all guarantees expire.
• Marmitek does not accept responsibility in the case of improper usage of the product or when the
product is used for purposes other than specified. Marmitek does not accept responsibility for
additional damage other than covered by the legal product responsibility.
Operating controls:
1. Wiring Terminals
2. Connector Socket
3. DC Power Connection
4. 4" flat CRT
5. Power LED
6. Handsfree Volume Control
7. Intercom and Broadcast Button
8. Lock Release Button
9. Video and Audio Monitoring
10. Brightness Control
11. Memory Status LED
12. Contrast Control
13. Infra Red Illumination LED’s
14. CCD Camera
15. Call Button
16. Door Unit Assembly Screw
17. Wall Mount Screws
18. Screw Wrench
19. Cover Label
20. AC Power Supply
MARMITEK 229 DOORPHONE SYSTEM
M229 Standard Parts

ENGLISH
WIRING DIAGRAM
3M229™
Avoid wiring along AC cords
Lock Release Control

ENGLISH
4© MARMITEK
M229 BASE STATION INSTALLATION
STEP1:
Connect 2 wires to the DR1 screw connection for the door camera (no polarity. Use a 2-ply cable:
1,0 mm2for distances up to 100 m). Then connect the power adapter to the DC power adapter
connection [3] (+ = red, - = black). Do NOT connect the power adapter to the mains. Place the
base station onto the wall plate.
150-170 cm from ground
Connect the wiring for the doorunit to terminal DR1 (no
polarity)
To AC outlet: do not connect yet.
2 wires
2 wires to connect the Lock
Release Control (if available)

ENGLISH
5M229™
Door camera
Power supply
24V/1A max
Electric door
lock
Door open output terminal
By pressing the middle button of the base station, an electric door lock can be controlled. The
door lock is connected to the DOOR RELEASE output terminals on the back of the door camera.
By repositioning the jumper at the back side of the camera you can toggle between two options:
1. Electric door lock with
its own power supply
(standard)
The door open contact is a dry contact.
Maximum load DC24V/1A or AC24V/1A.
Diagram:
2. Electric door lock
powered by
M229 system
The door open contact provides the power for
the electric door lock. Output voltage 12V,
maximum current 300mA. Diagram:
STEP 2:
To mount the door unit, first mount the metal Wall Plate. Connect the 2 wires from the base
station (monitor) to the terminals "MONITOR" (no polarity). If required, connect 2 wires for the
Lock Release Control to the terminals "DOOR RELEASE". See below for more details.
WARNING: The system will only work when a door camera is connected to connector DR1. If no
camera is connected to DR1, you cannot view any camera images or activate the menu.
Mount the door unit on the metal Wall Plate, using the screw (16) supplied.
See the description below for more information. An overview of all the connectors on the camera
can be found op page 17.
Connection for existing doorbell
An existing doorbell can be connected to the Marmitek EX-229D door camera, (part of the
Marmitek M229 system). As a result, the existing doorbell will be activated when the button of
the EX-229D camera is pressed.
To connect the doorbell system to the door camera, a small output terminal is available on the
back of the EX-229D door camera. A hook up wire for this terminal is supplied. You’ll find this
wire in the accessoires bag. The maximum voltage and current that can be switched with this
terminal (dry contact) is 12V/50mA.
The actual doorbell current of most doorbell installations is higher and therefore it has to be
switched with a relay. The relay is controlled by the extra output terminal of the camera.
Door camera
12V / MAX 300mA
Electric door
lock

6© MARMITEK
ENGLISH
STEP 3:
Plug in the AC adapter of the base station (monitor)
STEP 4:
Press the Audio-Video Monitoring button (4) to test the system.
2 wires to DR1
terminals of the
Base station
(monitor)
2 wires to connect a Lock Release
Control (if available)

7M229™
ENGLISH
STEP 5:
Adjust the Viewing Angle of the Door Unit.
Use the supplied Screw Wrench,
and push the built-in camera unit
gently forward to adjust the angle
(use the left or right hole
respectively to adjust to the
required direction).
STEP 6:
Assemble the Door Unit.
Fix the screw (16) and use the adhesive label to cover the screw. Remove transparent protection.

8© MARMITEK
ENGLISH
M229-BASE STATION SETUP
Press and hold the left button (7) for 2 seconds. A beep indicates the system is in Setup mode.
A Menu is displayed on the monitor.
By pressing the left (7) and right (9) buttons you can step
through the Menu options.
With the middle (8) button you can change the settings.
• When the Memory LED [11] flashes quickly, the time
and date settings have to be programmed. Format for
date and time: YY/MM/DD HH:MM. The built-in
back-up battery will retain the time, date and stored
pictures during 1 hour in case of power failure.
• In case of power failure the settings will be retained.
• DR4/CAM3, DR3/CAM2, DR2/CAM1 should remain in
OFF position if no expansions are installed.
• Pick up the handset en replace it to exit the
Set-Up mode.

9M229™
ENGLISH
M229 – USING THE BASE STATION
1. Visitor calls from door unit:
• After 4 seconds, the Marmitek
Video doorphone
automatically records
the picture in the memory.
• If the handset is not picked up, the connection will be automatically switched off 30 seconds
after the last call trigger.
• If the Handset is picked up, it will be switched off after 90 seconds, or earlier if the Handset is
replaced on the monitor unit.
• If the Handset is not activated (e.g. nobody home), the Memory LED (11) will slowly flash to
indicate that new pictures are stored in the memory.
2. Audio and Video Monitoring without activitating the Handset.
• Press the right Button (9) for monitoring
without activating the Handset.
• If more Door units or cameras are connected,
you may select the required camera by
pressing the button 2, 3 or 4 times.
• The mode will automatically be exited after
90 seconds, or if the handset is picked up.
The mode will also be exited if a visitor calls
from the door unit.
DING DONG
DING DONG
Activation of
Audio and
Video.
Lock Release
Volume adjustment
(only for hands-free mode)
DING DONG
DING DONG

10 © MARMITEK
ENGLISH
3. Watching new pictures added to the memory
• If the Memory Status LED (11) is flashing slowly, a new picture (max. 32) has been captured.
• Press and hold the middle button (8) for at least 2 seconds. A beep indicates you are in Memory
mode. The most recently captured picture are displayed.
• With the right (9) button you can scroll through all the pictures in the memory.
The capture date and time is displayed for your information.
• New pictures are always stored in the memory. Older pictures then move down a space.
The picture last in line will disappear from the memory.
• The LED will stop flashing after you have watched all new pictures.
• In the top-right corner of the picture you can see which camera took this picture.
• To exit the Memory Mode, pick up the handset. The mode will also be exited if a visitor calls
from the door unit.
4. Other Functions:
• The Memory LED indicator (11) flashes (quickly) to indicate that a major power failure occurred
and the time and date need to be reset (See: M229 Base Station Set-Up).
Memory LED indicator