Marmitek Digimax 210 User manual

VIDEO
DOORPHON
20650/20151030 • VIDEO DOORPHONE 210™
ALL RIGHTS RESERVED MARMITEK ©
VIDEO
DOORPHONE 210
™
USER MANUAL 3
GEBRAUCHSANLEITUNG 21
GUIDE UTILISATEUR 41
MODO DE EMPLEO 61
MANUALE D’ISTRUZIONI 81
GEBRUIKSAANWIJZING 101

© MARMITEK
2

Video DoorPhone 210
3
ENGLISH
SAFETY WARNINGS
xDo not expose the components of your system to extremely high
temperatures or bright light sources.
xImproper use, self-installed modifications or repairs will void any and all
warranties. Marmitek does not accept any product responsibility for
incorrect use of the product or use other than for which the product is
intended. Marmitek does not accept liability for any consequential
damage other than the legal product responsibility.
xThis product is not a toy. Keep out of reach of children.
xDo not open the product (battery panel is an exception): the device may
contain live parts. The product should only be repaired or serviced by a
qualified expert.
xKeep batteries out of the reach of children. Dispose of batteries as
chemical waste. Never use old and new batteries or different types of
batteries together. Remove the batteries when you are not using the
system for a longer period of time. Check the polarity (+/-) of the
batteries when inserting them in the product. Wrong positioning can
cause an explosion.
xOnly connect the adapter to the mains after checking whether the mains
voltage is the same as the values on the identification tags. Never
connect an adapter or power cord when it is damaged. In that case,
contact your supplier.
xDisconnect the AC/DC power adapter from the mains when this device is
not in use for prolonged time.

© MARMITEK
4
TABLE OF CONTENTS
SAFETY WARNINGS .....................................................................................3
TABLE OF CONTENTS..................................................................................4
INTRODUCTION ............................................................................................5
FEATURES.....................................................................................................5
SET CONTENTS ............................................................................................5
CONTROLS LAYOUT.....................................................................................6
GETTING STARTED ......................................................................................7
Power Supply ..............................................................................................7
Door unit ..................................................................................................7
Backup ........................................................................................................7
Handset ...................................................................................................8
Pairing the handset and the door unit .........................................................9
Mounting of door Unit................................................................................10
Always close..........................................................................................10
Always open ..........................................................................................10
Auxiliary terminal ...................................................................................11
OPERATION.................................................................................................11
ON / OFF...................................................................................................11
CALLER SETTING .......................................................................................12
GATE ........................................................................................................12
VOLUME...................................................................................................12
BRIGHTNESS...........................................................................................12
CONTRAST ..............................................................................................12
GATE LIGHT.............................................................................................13
ALARM MODE ..........................................................................................13
DOOR LOCK OPEN .................................................................................13
TRIGGER TIME ........................................................................................13
DATE/TIME...............................................................................................13
EXIT ..........................................................................................................14
MISSED CALL(S)......................................................................................17
PRECAUTION...........................................................................................17
FREQUENTLY ASKED QUESTIONS...........................................................18
TECHNICAL DATA.......................................................................................19
COPYRIGHTS ..............................................................................................20

Video DoorPhone 210
5
ENGLISH
INTRODUCTION
Congratulations on your purchase of the Marmitek Video DoorPhone 210.
Your Video DoorPhone 210 has been manufactured and checked under the
strictest possible quality control to ensure that each Video DoorPhone 210
leaves the factory in perfect condition. In the unlikely event you find any
defect or experience any problem, please contact our service centre or
dealer, do not attempt to repair by yourself.
Please read this manual carefully to obtain optimum performance and
extended service life from the system.
FEATURES
xMobile wireless video doorphone system.
xAlways see who's at the door before you open it, from anywhere in your
home.
xGet a good view of people day and night, with a digitally adjustable
camera angle, zoom feature and LED lighting.
xInterference-free coverage, anywhere in your home.
xEasy installation, using existing wiring.
xIncluding missed call notification and automatic image storage of last 10
visitors.
xRugged, weatherproof housing.
xOpen the door remotely by electric door opener (optional).
xSelectable doorbell warning: audio, visual and/or vibrate.
xDigital transmission - ensures interference-free calls.
SET CONTENTS
a. Handset
b. Door Unit
c. Charger stand
d. Switching power
supply for
charger stand
e. Rechargeable Li
battery pack
(installed in
handset)
f. Tool
g. Screws and rivets
h. Manual

© MARMITEK
6
CONTROLS LAYOUT
Handset unit
1. Call button
2. Microphone
3. Speaker
4. White illumination LED
5. Light sensor
6. Camera lens
7. Pairing button
8. Terminal block
9. Volume down/Left key
10. Volume up/Right key
11. Menu key
12. Image shift key
13. Door lock open key
14. Missed calls key
15. Hang up and power ON/OFF button
16. Talk and answer button
17. Microphone
18. TFT screen
19. Speaker
20. Power and battery low indicator
21. USB port
Charging stand
Door unit

Video DoorPhone 210
7
ENGLISH
GETTING STARTED
Power Supply
Door unit
With the supplied tool, loosen the screws holding the unit from the mounting
bracket. The screws are made specifically for anti-theft purposes. It is
necessary to keep the tool in a safe place for when you need it later when
replacing batteries. The door unit is powered with 8 to 12V AC or 12V DC.
Connect a power supply to the terminals (8) at the back marked with (not
included).
In case of a power failure, the unit will automatically switch to power from the
alkaline batteries (if installed).
You can use your existing doorbell transformer as power supply, as long as it
can provide 8…12V, AC or 12V DC. When you want to use another 12V
power supply, make sure it has a stable voltage output (Switching adapter
100-240VAC (V) 12VDC) and not a transformer type that has a high no load
voltage!
Backup
Insert three UM-4 size AAA alkaline cells into the battery compartment;
observe correct polarity. We strongly recommend using alkaline batteries
instead of rechargeable batteries because at low temperatures (below 0˚C),
rechargeable ones have poor performance and their capacity will fall.
Please note the alkaline batteries are used only as a backup in case of mains
failure. They can only last for 1 - 2 days under normal operation.

© MARMITEK
8
Handset
The supplied Li
polymer battery
pack is already
installed in the
handset. (To
replace the battery,
press down and
slide open the
battery door in the direction as shown, take out the battery pack and
disconnect it from the socket.
With the handset
remaining switched off,
place it onto the charger
stand.
Plug in the supplied AC
switching power supply
into an AC outlet and
connect its output plug
to the USB port (21)
located at the back of
the charger stand.
The power indicator (20)
should light up red during the charging process. Adjust the position of the
handset in the charger stand in case this indicator does not light up. During
charging, in case the screen (18) is turned on, the segments within the
battery icon will flash in turn.
The battery pack should be fully charged within 4 hours when used for the
first time. The power indicator (20) will now go off (if the handset is switched
off) or turn steady blue (if the handset is switched on).
Now the unit can be switched on and is ready for operation. Either taking out
the unit or keeping it placed in the charger stand will cause no damage to the
battery. In the latter case, when the battery is being consumed and voltage
falls to a certain level, the charger stand will automatically charge up the
battery.
CAUTION: BE SURE THE BATTERY IN THE HANDSET IS A
RECHARGEABLE TYPE BEFORE YOU PLACE IT IN THE CHARGER
STAND, OTHERWISE AN EXPLOSION MAY RESULT.

Video DoorPhone 210
9
ENGLISH
Pairing the handset and the door unit
This process is to match the door unit with the handset so that they can
communicate with each other and so that no other devices (even a
doorphone of an identical model) can interfere with your set.
The door unit and handset are already paired when they are shipped from the
factory. However, in case interference still exists, perform pairing again to
achieve better privacy and to avoid false triggering of the door lock from a
nearby doorphone system.
Place the door unit and handset close to each other
within a distance of 1m.
Press and hold the talk/answer button (16), then long
press the power ON/OFF button (15) to switch on
the unit. The screen (18) will show the following:
Use the left/right key (9)(10) to select either
“FRONT” (represent front gate), “BACK” (represent
back gate) or “CLEAR”, then touch the menu key
(11) to confirm. The power indicator (20) should now
flash rapidly, showing the handset has entered pairing
mode.
In case “CLEAR” is selected, all the originally paired
door units will be cleared and you will then need to
perform pairing again.
Now install alkaline batteries or connect 12V DC to the
door unit. (If the door unit was already on, do a
powercycle.) Then short press the pairing button (7)
located at the back.
WARNING: The pairing button (7) must be pressed
within 30 sec once you supply power to the door unit, otherwise pairing
will not be successful.
Once the handset and the door unit are successfully paired, the image
captured by the camera lens (6) will be shown in the screen (18) of the
handset. The doorphone is now ready for operation. If the pairing process is
not successful (the screen (18) remains blue), repeat the procedures from
step 2 again. Remember when you add a second door unit to the system (for
back gate use), it is necessary to perform the pairing process and select
“BACK”. The original front gate unit does not need to be paired again.

© MARMITEK
10
Mounting of door Unit
Select a location near your door entrance
where the surface is not too rough. We
recommend that you do some polishing to
get a plane surface or otherwise the unit
may not be able to mount properly.
It should be noted that the mounting bracket
is not installed on metal screening surfaces
nor in the vicinity of other electronic devices
that may reduce the operating range. Using
the supplied self tap screws, fix the
mounting bracket onto the wall.
Connect the terminals marked of the
12V DC power supply at the back of the
door unit. In addition, there are also
terminals marked and for
connecting to an electric door latch which
can be remotely opened by the handset.
When the DC power supply is connected,
the call button (1) will be illuminated. The
electric door latch opening feature will not
operate when using the backup alkaline
batteries so as to keep long battery life.
CAUTION: When using the DC supply, in case the electric door latch
does not function, reverse the polarity it is connected to and try again.
(The two most common types of electric door latch on the market are either
“always close” or “always open”.)
Always close
These two terminals normally provide a 12V supply. During
communication, once the door lock opening button (13) is pressed, this
voltage will drop to 0V temporarily for duration of time as specified by the
TRIGGER TIME function.
Always open
These two terminals normally provide 0V. During communication, once
the door lock opening button (13) is pressed, the terminals will provide a
12V supply temporarily for duration of time as specified by the TRIGGER
TIME function.
Under no circumstances should AC mains Voltage be directly connected to
the terminal blocks (8)!
Drilled holes
Insert the plugs into the holes
(for concrete wall only)