Mars AE2611 User manual

22201302
Page 1 of 6
Rev. A
Installation Instructions
These instructions outline the procedures to install a Mars AE2611 or AE2411 as part of the
Rowe®JUMP Kit for CD-100, CD-100A or CD-100B jukeboxes.
Tools Required
1/4”, 5/16” and 11/32” nut drivers, 1/2” Open End Wrench, Philips Screwdriver
Also required - Mars AE2411 or AE2611 Bill Acceptor
Parts Included with this Kit
Item Part Number Description Quantity
1 34064201 Lower Adaptor Bracket 1
2 34064801 Guide Plate 1
3 87842300 #6-32 Nuts 4
4 80713006 #8-32x3/8 Sems Machine Screw 1
5 40956301 Upper Adaptor Bracket 1
22201302 These Instructions 1
Installing a Mars®Bill Acceptor with your JUMP™Kit
Figure 1
3
125
4

22201302
Page 2 of 6
Rev. A
Instructions
1. Disconnect and remove the OBATransport from the jukebox. Set it aside.
2. Remove the stacker and it’s harness from the jukebox by removing the 2 front mounting screws and loosening
the 2 rear screws as shown in Figure 2. Save the screws for use later in Step 8.
Figure 2
3. Remove the plastic faceplate from the OBA-2 Transport. Save the 4 philips screws for use later in Step 7.
4. Remove (4) #8-32 nuts and the #8-32 screw to remove the OBA-2 Transport from it’s Mounting Bracket.
Save the (4) nuts.
Remove these 2
screws Loosen these 2 screws

22201302
Page 3 of 6
Rev. A
Figure 3
5. Assemble the upper and lower Mars adaptor brackets to the OBA-2 Mounting Bracket as shown in
Figure 3 using the nuts removed in Step 4. See Figure 3.
6. Mount your MarsAcceptor onto the bracket using the 4 nuts provided. To provide the smoothest opera
tion, push the Acceptor as far as possible away from the bracket as you tighten the unit to the brackets.
7. Install the new trim plate supplied with your JUMP Kit using the 4 philips screws removed in Step 3.
See Figure 4.
Figure 4
Push the Mars Acceptor in
this direction as you tighten
in place
Lower Bracket
Upper Bracket
OBA-2 Mounting
Bracket

22201302
Page 4 of 6
Rev. A
9. Slide the BillAcceptorAssembly onto
the guide rail making sure that the lower
bracket is fitted into the groove on the
roller/spacer. Leave the acceptor
sticking out a little farther than it would
normally be and pull the roller/spacer
outward along with the Acceptor so that
it maintains contact. Carefully lower the
front door and gently latch it, allowing it
to push the bill acceptor and roller/
spacer rearward. Once the door is
latched, open it and using the open end
wrench to hold the roller/spacer, tighten
the Sems screw. Close the door once
again to verify that there is a snug fit
between the front of the acceptor and
the door. See Figure 5.
8. Remove the roller/spacer from the OBA-2’s Bill Stacker as shown in Figure 4. Slide the Guide Plate (Item
2) over the screw present on the bill acceptor mounting panel and secure in place using one of the #8-32
machine screws removed in Step 2. Install the roller/spacer as shown in Figure 4 using the Sems Head
machine screw (Item 4) but do not tighten.
Figure 4
Roller/Spacer
OBA-2 Stacker Tighten this
screw to secure
Slide the plate
ocer this screw
Sems Head Screw
(Item 4)
Guide
Rail
Figure 5
Move the roller/spacer forward
with the Bill Acceptor

22201302
Page 5 of 6
Rev. A
Figure 6
12. Route the logic wire bundle of the bill acceptor harness to the left, beneath the core computer and then up to
the Rowelink Controller and plug it into P19.
13. Set the DIP switches on the bill acceptor:
For AE2411 ($1 and $5) - Switches 7 and 8 must be OFF. The others are optional, but Rowe suggests
that you leave 3 OFF and turn 1, 2, 4, 5 and 6 ON
For AE2611 ($1 thru $20) - Switch 6 must be ON and Switches 7 and 8 must be OFF. The others are
optional, but Rowe suggests that you turn Switches 1, 2 and 3 ON and Switches 4 and 5 OFF.
14. After you finish the remaining JUMP Kit installation, or if you have already finished the Kit installation, turn
the jukebox ON and check for proper bill acceptance and credit.
Main Harness
Ballast
Harness
Bill Acceptor
Harness
10. Plug the appropriate connectors of the Bill Acceptor Harness, P/N 34022323 included with your
JUMP Kit, into the headers on the side of the acceptor. Route the harness to the cable clamp just below the
right hand hold. (Leave enough slack at the Acceptor to allow you to pull it out and remove the bills.) The
cable separates here with the power lines continuing up to the area near the ballasts (Step 11) and the logic
wires heading to the left and over to P19 on the Rowelink Controller (Step 12).
11. Disconnect the 120VAC ballast harness connector and plug the 4-way male connector of the BillAcceptor
Harness into the jukebox 120VAC connector. Plug the ballast harness into the empty 4-way connector on
the bill acceptor harness. See Figure 6.

22201302
Page 6 of 6
Rev. A
This page intentionally left blank.