Martin MAC Viper Profile User manual

Martin MAC Viper Quadray™ Beam Kit Installation and DMX Control Guide 1
MAC Viper™ Beam Kit
Installation Guide
Safety information
Warning! Read the following information carefully before installing the lens and make sure that
any person who uses, services, installs or transports the fixture and lens also has this
information.
Warning! Follow all the safety precautions in the fixture’s user documentation and use the
documentation for reference when installing accessories and using the modified product.
Safety and Installation guides are supplied with fixtures, but check that you have the latest
revision of the user documentation. This is available for download from the fixture’s Product
Support page at www.martin.com
Warning! Accessories must be installed by qualified professional technicians only.
Warning! Disconnect the fixture from power and allow to cool for at least 30 minutes before
starting work.
Warning! With the Beam Kit installed on a MAC Viper AirFX, do not illuminate surfaces within
4.2 m (13.8 ft.).
Warning! The MAC Viper AirFX Beam Kit increases the length of the fixture’s head. There is a
risk of head collision and a danger of falling objects if the instructions in this guide are not
followed carefully. In particular:
• Before installing the Beam Kit, check that the fixture is running firmware version 1.3.0 or later
and check that the head is perfectly vertical when tilt is set to 0°. If necessary, update the
fixture’s firmware and calibrate the head in the control menu as directed in the MAC Viper
AirFX user documentation.
• Do not apply power to a fixture with a Beam Kit installed if the Beam Kit’s connector is not
plugged into its socket in the fixture’s head.
• Remove any oversize XLR connectors such as 3-pin to 5-pin XLR adapters from the DMX
sockets.
• Remove the Beam lens before opening the Tilt calibration menu in the control panel.
If you have any questions about how to install this or any Martin™ product or use it safely, please contact your
local Martin Professional™ distributor (see www.martin.com/distributors for details) or call the Martin™ 24-hour
service hotline on [phone], or in the USA on 1-888-tech-180.
© 2013 Martin Professional A/S. Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark. Information subject to change without notice. Martin
Professional A/S and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic
loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this document. The Martin logo,
the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional A/S or its affiliates
and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000631 Rev. B

2 Martin MAC Viper Quadray™ Module Installation and DMX Control Guide
Important! Make sure that the front of the head does not face the sun or any other strong light
source directly for longer than a few seconds at any time. Lenses can focus the sun's rays
inside the fixture, causing internal damage and creating a possible fire risk
Important! Do not use concentrated alcohol solutions, abrasive products or solvents to clean
lens accessories. If wiping with a soft, lint-free cloth dampened with distilled water is not
effective, damp the cloth with distilled water containing 20% isopropyl alcohol in solution.
Introduction
This guide explains how to install the Martin MAC Viper™ Beam Kit, P/N 91614053, on a Martin MAC Viper
AirFX™ fixture.
Installing a front lens accessory kit takes only a few minutes. If you keep the standard components that you
remove when you install the lens, it can be uninstalled and the fixture returned to standard configuration at any
time.
Preparation
The MAC Viper Beam Kit contains the following items:
• Beam lens
• Mounting collar with attached multiconnector and Beam Kit
safety wire
• This Installation Guide
Remove any adhesive tape that is applied to the components
in the kit to avoid loss or damage during transport.
Keep the protective packaging supplied with the kit for
possible re-use.
Software compatibility and tilt limits
MAC Viper AirFX firmware version 1.3.0 or later must be installed before installing the Beam Kit. The latest
version of the MAC Viper AirFX firmware is available for download from the MAC Viper AirFX Product Support
page on the Martin™ website at www.martin.com
When firmware version 1.3.0 is installed and the Beam Kit’s multiconnector is connected to its socket in the head,
the MAC Viper AirFX recognizes that the Beam Kit is installed and limits tilt range by 10° at each end so that the
head cannot collide with the base. Total tilt range with the Beam Kit installed is 254°.

Martin MAC Viper Quadray™ Beam Kit Installation and DMX Control Guide 3
Installation procedure
Warning! Disconnect from power and allow to cool for 30 minutes before handling the head.
To install the Beam Kit on a standard Martin MAC Viper AirFX fixture:
1. Check that firmware version 1.3.0 or later is installed in the fixture. If it is not, install it following the instructions
in the MAC Viper AirFX user documentation.
2. Check that the head is perfectly vertical when tilt is set to 0°. If it is not, use the fixture’s control panel to
calibrate tilt following the instructions in the MAC Viper AirFX user documentation.
3. Disconnect the fixture from power and allow components to cool for 30 minutes.
4. Remove any 3-pin to 5-pin XLR adapters or other oversize connectors from the fixture’s DMX sockets. With
the Beam Kit installed, use only standard-size 5-pin XLR connectors such as those found on Martin™ DMX
cable.
5. Place the fixture on a secure work surface. Tilt the head vertically upwards and apply the tilt lock.
6. See Figure 1. Remove the top head cover by loosening its Torx 25 captive retaining screws Auntil the screws
turn freely (the top head cover is on top of the head with the text on the back of the head facing the right way
up). Lift the front of the cover slightly away from the head, then slide the cover towards the front of the head to
release the rear of the cover. You can allow the head cover to hang on its safety wire, but for easiest access
press the cover’s safety wire retaining clip Bin towards the head chassis, slide the clip until you can remove it,
then remove the head cover completely from the fixture.
7. See Figure 2. Release the four screws from the front lens, then release
the front lens safety attachment. Remove the front lens and store it for
possible re-use if the fixture is returned to standard configuration at a
later time.
8. See Figure 3. Undo the two clips Afrom the Beam
Kit assembly and separate the Beam lens unit B
from the mounting collar C.
Figure 1
A A
B
Figure 2
A
C
B
Figure 3

4 Martin MAC Viper Quadray™ Module Installation and DMX Control Guide
9. See Figure 4. Line up the Beam Kit mounting
collar over the head so that the kit’s safety wire
will pass through the cutout Ain the front of the
head above the safety wire attachment point and
the connector attachment wire will pass through
the cutout Bin the opposite side of the head,
above the lens accessory socket C.
10. Lower the mounting collar onto the head, making
sure that it sits completely square to the head. Do
not use excessive force. You may need to rotate
the collar slightly to the left and to the right until
you can feel that it has engaged correctly. Check
that the safety wire and the connector attachment
wire are not trapped between the collar and the
head.
11. See Figure 5.
Fasten the
collar in place
by tightening
the four Torx 20
screws
(arrowed) on
the front of the
collar.
12. See Figure 6. Pass the Beam Kit’s safety wire
through the hole Ain the head chassis and then
into the safety wire attachment point B. Push and
slide the fastener so that it is locked into the
attachment point.
Figure 4
AB
C
Figure 5
Figure 6
A
B

Martin MAC Viper Quadray™ Beam Kit Installation and DMX Control Guide 5
13. See Figure 7. Push the Beam Kit multiconnector
(arrowed) onto the corresponding socket in the
head and fasten it onto the socket with the two
Torx 10 screws in the multiconnector.
14. Reinstall the top head cover (see Figure 1),
checking that the Beam lens safety wire and
connector attachment wire are not trapped under
the cover during reassembly. Check also that the
top head cover’s safety wire is securely attached
before tightening the head cover retaining screws.
15. See Figure 8. Hold the Beam lens over the
mounting collar. Lift up the end of the lens safety
wire attachment Aso that the wire can reach its
attachment point B and push and slide it so that it
is locked into the attachment point.
16. See Figure 9. Place the
Beam lens onto the
mounting collar so that its
two clips line up with the
latching points in the
collar (arrowed) and
fasten the clips.
17. Release the tilt lock, then
apply power. With MAC
Viper AirFX firmware
version 1.3.0 or later
installed, the fixture will
recognize that the Beam
Kit is installed and limit
the tilt range so that the
Beam lens cannot collide
with the base.
18. Check and if necessary adjust the lamp alignment as described in the MAC Viper AirFX user manual. Remove
any significant hotspot in the beam.
19. Precautions are necessary in order to avoid personal injury or damage to the fixture or Beam Kit during use,
service and transport in the flightcase. Read “Safety information” on page 1 and “Packing in the flightcase” on
page 6.
When the Beam Kit is installed as described above and the fixture is powered on, the MAC Viper AirFX
recognizes the Beam components automatically and configures itself for operation with the Beam lens. If you
remove the Beam Kit and reinstall the standard components, the fixture will recognize that no Beam lens is
present and reconfigure itself for operation without the Beam.
Figure 7
Figure 8
A
B
Figure 9

6 Martin MAC Viper Quadray™ Module Installation and DMX Control Guide
Packing in the flightcase
The Beam lens must be removed from the MAC Viper AirFX before the fixture is packed in the Martin™ MAC
Viper flightcase for transport. To pack the fixture in the flightcase:
1. Unclip the Beam lens from its mounting collar with reference to Figure 9 on page 5. Leave the mounting collar
installed on the fixture
2. Disconnect the Beam Kit safety wire from the Beam lens with reference to Figure 8 on page 5 and remove the
Beam lens from the fixture.
3. Pack the fixture in the flight case without the Beam lens. Store the Beam lens separately.
Specifications
The MAC Viper AirFX™ with the MAC Viper Beam Kit installed weighs 37.6 kg (82.9 lbs.). It has the dimensions
shown in millimeters below:
For full specifications, see the Product Support page for the MAC Viper Beam™ on www.martin.com
This minimum center-to-center
distance can be reduced if pan limits
are set via the control menus
551
473
701
335
885
785
866
255

Martin MAC Viper Quadray™ Beam Kit Installation and DMX Control Guide 7

Martin Professional A/S •Olof Palmes Allé 18 •8200 Aarhus N •Denmark
Tel: [phone] •Fax [phone] •www.martin.com