Mastech MS5308 User manual

Page 1 of 17
1.
1.1.
1. General instructions:
Thank you for purchasing a MS5308 LCR digital bridge meter.
The MS5308 LCR digital bridge meter is a professional
instrument for measuring inductance, capacitance and resistance.
It has many features, such as automatic identification, automatic
measurement range, high measurement accuracy and speed, wide
measuring range and so on.
An ordinary multimeter only provides DC mode for resistance
measurement, while the MS5308 provides both AC and DC
measurement modes. A variety of test frequencies up to 100Khz
can be provided for inductance, capacitance and resistance in AC
mode to meet the actual needs better.
Correct usage can ensure that the instrument will work precisely
for a long time. Please read the instructions carefully before using
and operate the instrument strictly in accordance with the
instructions .
1.1 ．
．．
． Panel description
1
Display
2
Functional buttons area
3
Power switch
4 IR Port
5
External power port
6
Calibration button port
7
DUT + jack
8
DUT - jack
9
Shielding grounding jack
1.2 ．
．．
． Inspection
When you get a new LCR meter, please check the instrument and
its accessories. If something is damaged or missed, please contact
the store you bought the instrument from for adjustment or
replacement.
1.3 Accessories
MS5308 LCR digital bridge meter Kelvin test clip (one pair)
SMD test probe IR data line
Upper computer program CD External power supply

Page 2 of 17
MS5308 panel

Page 3 of 17
2. Safety instructions:
Operating environment and condition:
●Elevation ＜ 2000 m
●Relative humidity (RH) ≦ 80%RH
●Operating temperature 0 – 40°C
Note: DO NOT input voltage at the measurement port. When
measuring capacitance, please discharge first then measure,
otherwise, the meter will be damaged.
Storage and maintenance: Do not use alcohol or other solvents
to clean the meter. If it will not be used for long time, please
remove battery and put the meter in a dry and clean
environment.
3. Description:
3.1 Definition Description
APO: Auto power off
LCR: This character showing on the LCD means that the tester
works in automatic identification mode
L
P:
Inductance parallel connection measurement mode
L
s:
Inductance series connection measurement mode
C
P:
Capacitance parallel connection measurement mode
C
s:
Capacitance series connection measurement mode
R
P:
Resistance parallel connection measurement mode
R
s:
Resistance series connection measurement mode
DCR: Resistance DC measurement mode
D: Wastage factor
Q: Quality factor
θ: Phase angle value
ESR: Equivalent resistance
DUT: Object for measuring
3.1 Impedance parameter description (see Figure Ⅰ )
Z= R
s
+jX
s
∠
=|Z| θR
s-
=|Z|CosθX
s
= |Z|Sinθ
X
s
/R
s
=Tanθθ=Tan
-1
(X
s
/R
s
)
If θ> 0, it means that the measured object is resistant, if θ< 0, it

Page 4 of 17
means that that the measured object is capacitive.
3.2 Series-parallel connection mode description
This meter has series and parallel measurement modes. When the
capacitance value of the measured object is large or inductance
value is small, use the series mode for more accurate results.
When the capacitance value of the measured object is small or
inductance value is large, use the parallel mode for more accurate
results. This meter can select the measurement mode
automatically according to the measured object.
4. Functional characteristics description:
1. 19,999 (main)/1,999 (secondary) dual LCD display
2. LCR measures with automatic identification and automatic
measurement range
3. L\C\R single measurement selection
4. Resistance measurement in DCR mode
5. D/Q/θ/ESR display on the secondary display
6. Series or parallel measurement modes are selectable
7. Comparison function under single measurement
8. Test frequency 100/120/1k/10k/100k is selectable in AC mode
9. The selection feature for measured components with the same
series
10. Battery power display, auto power off if meter is not operated
for 5 minutes.
11. With infrared transmission interface, the meter is secure
(supporting hot plug). With special software, the meter is easily
managed.
12. See table 1-3 for measurement accuracy and scope
Remarks: This accuracy is the measurement standard. In
DUT jack, the meter-specific probe should be used if required.
Measurement with probe may be influenced by external
environment. To avoid inaccurate measurements, please keep
away from strong magnetic sources.

Page 5 of 17
Table 1 Resistance measurement scope
Note: This accuracy is the measurement standard when D
<0.1, if D> 0.1, it should be multiplied by the extraction
of a root of 1 + D
2
Measurem Measurement Measureme Resolutio Accuracy
R
S
/R
P
100Hz/120 200.00Ω0.01Ω1.0%+5d
100Hz/120 2.0000KΩ0.1Ω0.3%+5d
100Hz/120 20.000KΩ1Ω0.3%+5d
100Hz/120 200.00KΩ0.01kΩ0.5%+5d
100Hz/120 2.0000MΩ0.1kΩ1.0%+5d
100Hz/120 20.000MΩ1kΩ1.0%+5d
100Hz/120 200.00MΩ0.1MΩ2.0%+5d
1kHz 20.000Ω0.001Ω1.0%+5d
1kHz 200.00Ω0.01Ω0.3%+5d
1kHz 2.0000KΩ0.1Ω0.3%+5d
1kHz 20.000KΩ1Ω0.3%+5d
1kHz 200.00KΩ0.01kΩ0.5%+5d
1kHz 2.0000MΩ0.1kΩ1.0%+5d
1kHz 20.000MΩ1kΩ2.0%+5d
1kHz 200.0MΩ0.1MΩ5.0%+5d
10kHz 20.000Ω0.001Ω1.0%+5d
10kHz 200.00Ω0.01Ω0.5%+5d
10kHz 2.0000KΩ0.1Ω0.3%+5d
10kHz 20.000KΩ1Ω0.5%+5d
10kHz 200.00KΩ0.01kΩ1.0%+5d
100kHz 20.000Ω0.001Ω1.0%+5d
100kHz 200.00Ω0.01Ω1.0%+5d
100kHz 2.0000KΩ0.1Ω1.0%+5d
100kHz
20.000KΩ
1Ω
2.0%+5d

Page 6 of 17
Table 2Capacitance measurement scope
Note: This accuracy is the measurement standard. When D
<0.1, if D> 0.1, it should be multiplied by the extraction of a
root of 1 + D
2
Measurem Measurement Measure Resoluti Accuracy
C
S
/C
P
100Hz/120 20.000nF 1pF 1.0%+5d
100Hz/120 200.00nF 0.01nF 0.5%+5d
100Hz/120 2000.0nF 0.1nF 0.5%+5d
100Hz/120 20.000uF 1nF 0.5%+5d
100Hz/120 200.00uF 0.01uF 1.0%+5d
100Hz/120 2000.0uF 0.1uF 2.0%+5d
100Hz/120 20.00mF 0.1mF 2.0%+5d
1kHz 2000.0pF 0.1pF 1.0%+5d
1kHz 20.000nF 1pF 1.0%+5d
1kHz 200.00nF 0.01nF 0.5%+5d
1kHz 2000.0nF 0.1nF 0.5%+5d
1kHz 20.000uF 1nF 0.5%+5d
1kHz 200.00uF 0.01uF 1.0%+5d
1kHz 2000.0uF 0.1uF 1.0%+5d
10kHz 200.00 0.01pF 1.0%+5d
10kHz 2000.0pF 0.1pF 1.0%+5d
10kHz 20.000nF 1pF 1.0%+5d
10kHz 200.00nF 0.01nF 1.5%+5d
10kHz 2000.0nF 0.1nF 2.0%+5d
100kHz 200.00 0.01pF 2.0%+5d
100kHz 2000.0pF 0.1pF 1.0%+5d
100kHz 20.000nF 1pF 2.0%+5d
100kHz 200.00nF 0.01nF 5.0%+5d

Page 7 of 17
Table 3. Inductance measurement scope
Note: This accuracy is the measurement standard. When D
<0.1, if D> 0.1, it should be multiplied by the extraction
Measurem Measurement Measureme Resoluti Accuracy
L
S
/L
P
100Hz/120 20.000mH 1uH 1.0%+5d
100Hz/120 200.00mH 0.01mH 0.5%+5d
100Hz/120 2000.0mH 0.1mH 0.5%+5d
100Hz/120 20.000H 1mH 0.5%+5d
100Hz/120 200.00H 0.01H 1.0%+5d
100Hz/120 2000.0H 0.1H 1.0%+5d
100Hz/120 20.000kH 1H 2.0%+5d
1kHz 2000.0uH 0.1uH 1.0%+5d
1kHz 20.000mH 1uH 0.5%+5d
1kHz 200.00mH 0.01mH 0.5%+5d
1kHz 2000.0mH 0.1mH 1.0%+5d
1kHz 20.000H 1mH 1.0%+5d
1kHz 200.00H 0.01H 2.0%+5d
1kHz 2000.0H 0.1H 5.0%+5d
10kHz 200.00 uH 0.01uH 1.0%+5d
10kHz 2000.0uH 0.1uH 0.5%+5d
10kHz 20.000mH 1uH 0.5%+5d
10kHz 200.00mH 0.01mH 1.5%+5d
10kHz 2000.0mH 0.1mH 2.0%+5d
10kHz 20.000H 0.001H 5.0%+5d
100kHz 20.000 uH 0.001uH 1.0%+5d
100kHz 200.00 uH 0.01uH 2.0%+5d
100kHz 2000.0uH 0.1uH 2.0%+5d
100kHz 20.000mH 1uH 2.0%+5d
100kHz 200.00mH 0.01mH 5.0%+5d

Page 8 of 17
of a root of 1 + D
2
5. Meter probe measurement
Use Kelvin clip or SMD clamp to connect according to the
following diagram:
Schematic diagram for using SMD clamp to measure
Remarks: insert the plug correctly according to the diagram.
Measurement can’t be done if inserted incorrectly

Page 9 of 17
Schematic diagram for using Kelvin clip to measure
Remarks: insert the plug correctly according to the diagram.
Measurement can’t be done if inserted incorrectly.

Page 10 of 17
6 Measurement operation description:
6.1. Automatic measurement:
When the instrument is turned on, the instrument will enter
automatic identification mode by default. At this time, insert the
object to be measured to the measurement side. The instrument
will automatically recognize that the object to be measured is
capacitive resistance or inductor and display the measurement
value in the main display, and display a corresponding
D/Q/θ/value in the secondary display. In this mode, you can
change measurement frequency by operating Frequency.
6.2. Single measurement
When the instrument is turned on, the instrument will enter
automatic identification mode by default. At this time, you can
select L, C, R, DCR and other single measurement modes by
operating Function button. Read the measurement value on the
LCD display after inserting the object to be measured and
selecting the proper mode. In L, C, R mode, you can change the
measurement frequency by operating Frequency button, and you
also can operate Series/Parallel buttons to select parallel
connection measurement or series connection measurement.
6.3. Comparison and selection
When the instrument is turned on, the instrument will be switched
to single measurement mode for the objects to be selected.
Connect the sample objects to be selected at measurement port. At
this time, you can operate Comparison button to enter
comparison and selection mode. PASS or FAIL, will display on
the main display and the measurement value of current object will
display on the secondary display. In this state, press Setup button