Masterflex 77123-00 User manual

Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
DESCRIPTION CAT. NO.
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
US & Canada only
Toll Free 1-800-MASTERFLEX | 1-800-637-3739
Outside US & Canada
1-847-381-7050
*EN809 manufactured by:
Masterflex LLC
28W092 Commercial Avenue, Barrington, IL 60010
[email protected] | www.masterflex.com
A-1299-7327 Edition 05
MASTERFLEX®SERIES
DIGITAL DISPENSING PUMP
Quick Start Guide

Pin No. DB-25
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
OFF TIME
TIEMPO DE INACTIVIDAD
HEURE D’ARRÊT
AUS-ZEIT
TEMPO DI SPEGNIMENTO
停机时间
OFFタイム
9
10
11
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
Description
1 Speed Control Voltage Input (0-10V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running Relay (N.O.)
7 Motor Running, Relay Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime, Local/Remote Grnd Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
9 Remote Voltage or Current Enabled
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Relay Common
22 Local/Remote Indicator Relay Common
25 Aux 24V+ (150 mA)
13 Aux 24V- (150 mA)
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line to
the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump. Use
appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose cloth-
ing could get caught in drive mechanism.
CAUTION: Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conduc-
tor must be connected to ground. Not for operation in wet locations as defined by
EN61010-1.
If the product is not used in a manner specified in the instructions, the protection
provided by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and cor-
rective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in opera-
tion. Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard
and corrective actions.
This product is not designed for, nor intended for use in patient connected applications;
including, but not limited to, medical and dental use, and accordingly has not been submitted for
FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as defined by ATEX
or the NEC (National Electrical Code); including, but not limited to use with flammable liquids.
BATCH COUNT
CONTEO DE LOTE
COMPTAGE DE LOT
FÜLLSTAND
CONTA LOTTO
批次数
バッチカウント
RECORD COPY
COPIA DE REGISTRO
ENREGISTRER COPIE
WIEDERHOLUNG AUFZEICHNEN
REGISTRA COPIA
复制记录
記録のコピー
ENT
ENT
ENT
ENT
ENT
ENT
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
Replacement Cord/Plug Sets Ordering Information
Catalog
number
Description DescriptionDescription Catalog
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
1
24 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4 3 2
25
2
year
warranty
70 dba @ 1M
-25C, -13F +65C, +149F
+0C, +32F +40C, +104F
EN61010-1:2010 L.V. DIR.
EN61326-1:2013 EMC DIR.
EN610000-4-2 Criteria C
EN60529 / IEC 60034-5
07525-20, -40
4.8 lbs (2.2 kg)
77123-00
4.5 lbs (2.0 kg)
IP
0.01-300 rpm
33

07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
07525-90 Power Supply, 24V DC output, 90 to 260V AC input
Product Accessories
1
2
3
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
8
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
管路校准
配管較正
ENT
ENT
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
9
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
拷贝输注模式
コピー給液モード
ENT
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
设置
セットアップ
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
ENT
ENT
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
PUMP SPEED
VELOCIDAD DE LA BOMBA
VITESSE DE POMPE
PUMPENGESCHWINDIGKEIT
VELOCITÀ POMPA
泵速
ポンプ速度
ENT
ENT
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
COPY
COPIA
COPIER
WIEDERHOLUNG
COPIA
复制
コピー
ENT
ENT

FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
流量单位
フロ－単位
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
连续模式
連続モード
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
键板上锁
キーパッド固定
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
泵流方向
ポンプ方向
PUMP RUNNING
BOMBA EN FUNCIONAMIENTO
POMPE EN FONCTIONNEMENT
PUMPE LÄUFT
POMPA IN FUNZIONE
泵的运行
ポンプ作動
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
启动/停止
始動/停止
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
设置
セットアップ
BACK
PARTE TRASERA
RETOUR
ZURÜCK
INDIETRO
返回
戻る
Graphic Interface Keypad Legend
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
输入
入力
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
遥控
遠隔操作
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
流量
流量
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
灌泵
呼び水
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
4SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
设置
セットアップ
ENT
ENT
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
5
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
流量单位
フロ－単位
ENT
ENT
6TUBING SIZE
TAMA—O DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
管路尺寸
管サイズ
ENT
ENT
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
7
® Digital
Dispensing Pumps
Quick Start Guide
Digital Pump
with Microflex
Pump Head
77123-00
Digital Pump
with Miniflex
Pump Head
07525-20
Digital Dispensing Pumps
.ON.TACNOITPIRCSED
07525-40
07525-20
Digital Pump 0.1 to 300 rpm with Single Channel Miniflex Pump Head
Digital Pump 0.1 to 300 rpm with Dual Channel Miniflex Pump Head
77123-00
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
E-mail: [e-mail]
www.masterflex.com • www.coleparmer.com
A-1299-7327
Edition 01
Digital Pump 0.1 to 300 rpm with Microflex Pump Head
Pin No. DB-25
Description
1 Speed Control Voltage Input (0-10 V)
2 Speed Control Current Input (0-20 mA)
3 Speed Control Input Ground Return
4 Speed Signal Current Output (0-20 mA)
5 Speed Signal Output Ground Reference
6 Motor Running N.O. Relay 1A @24V
7 Motor Running Common
8 Reserved - Not Used
14 Speed Signal Voltage Output (0-10 V)
15 Remote Start/Stop Input
16 Remote CW/CCW Input
17 Remote Start/Stop, CW/CCW, Prime Ground Ref.
18 Tach Ground Reference
19 Tach Output (Open Collector)
20 Remote Prime Input
23 General Alarm Relay
24 Local/Remote Indicator Relay
10-12 Reserved - Not Used
21 General Alarm Common
25 Aux 24V+
13 Aux 24V-
Pin No.
DB-25
SAFETY
PRECAUTIONS
Explanation of
Symbols
WARNING:
Product Use
Limitation
DANGER: Remove power from the pump before any cleaning operation is started.
WARNINGS: Remove power from the pump before attempting any maintenance.
A contactor or other device that routinely disconnects and reapplies the AC line
to the drive to start and stop the motor can cause drive hardware damage. The drive is
designed to use control input signals that will start and stop the motor.
WARNINGS: Tubing breakage may result in fluid being sprayed from pump.
Use appropriate measures to protect operator and equipment.
Unplug Pump System before removing or installing tubing. Fingers or loose clothing
could get caught in drive mechanism.
CAUTIONS:
Unplug Pump System before connecting the external remote control
cable to prevent damage to the drive.
CAUTIONS: To avoid electrical shock, the power cord protective grounding conductor
must be connected to ground. Not for operation in wet locations as defined by EN61010-1.
If the product is not used in a manner specified in the instructions, the protection provided
by the equipment may be impaired.
CAUTION: Risk of Danger. Consult Operator’s manual for nature of hazard and
corrective actions.
CAUTION: Risk of crushing. Keep fingers away from rotor while pump is in operation.
Stop pump before loading or unloading tubing.
CAUTION: Risk of electric shock. Consult Operator’s manual for nature of hazard and
corrective actions.
This product is not designed for, nor intended for use in patient connected
applications; including, but not limited to, medical and dental use, and accordingly
has not been submitted for FDA approval.
This product is not designed for, nor intended for use in hazardous duty areas as
defined by ATEX or the NEC (National Electrical Code); including but not limited to
use with flammable liquids.
Replacement Cord/Plug Sets Ordering Information
Catalog
number
50001-60
50001-62
50001-64
50001-68
50001-69
50001-70
50001-72
50001-74
50001-76
50001-78
—
Italy
U.S. 230V
—
Israel
Europe
England
Switzerland
noitpircseDnoitpircseD Description
number
Catalog
number
Australia
Denmark
India
U.S. STD. 115V
——
Catalog
0.1 - 300 rpm
07525-20, -40
4.8 lb (2.2 kg)
77123-00
4.5 lb (2.0 kg)
9 Remote Voltage or Current Enable
10 BATCH COUNT
OFF TIME
11
ENT
ENT
RECORD COPY
ENT
9
22 Local/Remote Indicator Common
07523-92 Footswitch w/DB-25 male connector
07523-94 DB-25 male connector for remote control
(connector only)
07523-95 Cable assembly, DB-25 male connector
and 25-ft (7.9m) cable w/stripped wire ends
07523-97 Dispensing wand DB-25 male connector
Product Accessories
1
2
3
8
COPY DISP. MODE
DUPLICAR DISP.
DISTR. REPETEE
WH.FÖRD.MOD.
MOD DIST COPIA
TUBING CAL
CAL DE TUBERÍA
ÉTALON. TUYAU
ROHRLEITUNGSKAL
TARATURA TUBI
07525-90 Power Supply, 24VDC output, 90 to 260 VAC input.
ENT
9
ENT
ENT
COPY
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
ENT
PUMP SPEED
ENT
CONTINUOUS MODE
MODO CONTINUO
MODE CONTINU
DAUERMODUS
MOD CONTINUA
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
PUMP DIRECTION
DIRECCIÓN BOMBA
DIRECTION POMPE
PUMPRICHTUNG
DIREZIONE POMPA
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
KEYPAD LOCKOUT
BLOQUEO DE TECLADO
VERROUILLAGE CLAV.
TASTENFELDSPERRE
BLOCCO DEI TASTI
REMOTE CONTROL
CONTROL REMOTO
TÉLÉCOMMANDE
FERNBEDIENUNG
CONTROLLO REMOTO
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
BACK
START/STOP
INICIO/DETENCIÓN
DÉMARRER/ARRÊTER
START/STOPP
AVVIO/ARRESTO
/
/
PRIME
CEBAR
AMORÇER
ANSAUGEN
ADESCARE
Graphic Interface Keypad Legend
6
4
5
ENTER
ENTRE
ENTRER
EINGABE
INSERIRE
PUMP RUNNING
ENT
SETUP
MONTAJE
INSTALLATION
SETUP
IMPOSTAZIONE
セットアップ
FLOW UNITS
UNIDADES DE FLUJO
UNITÉS DE DÉBIT
DURCHFLUSSEINHEIT
UNITÀ DI FLUSSO
TUBING SIZE
TAMAÑO DEL TUBO
TAILLE DU TUYAU
ROHRLEITUNGSGR.
DIMENSIONE TUBI
ENT
ENT
ENT
7
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
FLOW RATE
CAUDAL
DÉBIT
DURCHFLUSSRATE
INDICE DI FLUSSO
流量
流量
ENT
ENT