Matador PALLADIUM 6 BURNER BBQ User manual

Retain manual for future reference.
PALLADIUM 6 BURNER BBQ
Model: HS-18MA9601

CONTENTS
FEATURES AND BENEFITS
IMPORTANT SAFETY WARNINGS
GAS LEAK TEST
GAS EMERGENCY PROCEDURE
GENERAL INFORMATION
EXPLODED PARTS VIEW
PARTS LIST
HARDWARE PACK
ASSEMBLY STEPS
BBQ LOCATION – OUTDOOR AREA
CONNECTION TO LPG
LIGHTING PROCEDURE
USING THE BBQ
USING THE SMOKER BOX
BBQ TIPS
BBQ MAINTENANCE
SPECIFICATIONS
CONNECTION TO NATURAL GAS
WARRANTY
3
4
5
6
7
8
9
11
12
23
25
26
27
28
29
30
37
38
40

MATADOR INSTRUCTION MANUAL 3
FEATURES & BENEFITS
Overall Barbecue Dimensions
4B
Freestanding
Length Height Depth
1775 mm 1195 mm 654 mm
Gas Output
Gas Type Burner
BBQ Side
LPG / U-LPG 15 MJ/h 15 MJ/h
Natural Gas 15 MJ/h 15 MJ/h
13
STEP 17
Insert the warming rack (3) on the firebox and side burner trivet (8) on the side burner as shown.
Fully assembled BBQ

IMPORTANT SAFETY
WARNINGS
FOR OUTDOOR USE ONLY
DO NOT OPERATE THIS APPLIANCE BEFORE READING THE INSTRUCTION
BOOKLET.
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT STORE CHEMICALS OR FLAMMABLE MATERIALS OR SPRAY
AEROSOLS NEAR THIS APPLIANCE.
DO NOT OPERATE THIS APPLIANCE INDOORS.
DO NOT ENCLOSE THIS APPLIANCE.
DO NOT LIGHT OR OPERATE WITH COVER ON.
Servicing can only be carried out by authorised technicians or licensed gas
fitters.
Conduct a thorough gas leak check every time the cylinder is replaced or
reconnected.
Do not store chemicals or flammable materials near this appliance.
Children must be supervised at all times while they are in the vicinity of this
BBQ to prevent burn injuries and to ensure they do not attempt to use the
BBQ.
In case of a fat fire, immediately isolate the gas supply - turn the LPG cylinder
valve off.
Allow the BBQ to cool before removing the drip tray. Hot fat can cause serious
injury.
This BBQ should not be located under overhead combustible construction.
Maintain the following minimum clearances to combustibles at all times:
From sides: 200mm From back: 500mm Overhead:1000mm
Turn all gas valves off including the LPG cylinder valve after use.
Never leave burners on high for more than 10 minutes unless actually cooking.
If the burner makes a loud roaring sound when lit, it may be burning inside. If
this occurs, turn the burner off, allow it to cool and light it again.
Do not delay ignition and allow a buildup of unburned gas.
Remove stickers (where fitted) from hood before use.
Do not store a spare LPG cylinder in the vicinity of the BBQ.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.

MATADOR INSTRUCTION MANUAL 5
Gas connections on the barbecue are leak tested at the factory prior to shipment
however, a complete gas leak test must be performed during assembly. The
cylinder to regulator connection must be leak tested every time the connection is
made. In order to test for a gas leak, complete the following steps.
1. Make a soap solution of one part liquid detergent and one part water.
GAS LEAK TEST
2. Ensure that the barbecue control knobs and LPG is turned off. Open the LPG
cylinder valve and apply the soap solution to the gas connections using a soft
bristle brush as seen below.
Soap bubbles will appear if there is a gas leak. In case of a leak, turn off the gas
supply. Tighten any leaking fittings, then turn the gas supply on and re-check.
Warning: Do not operate the appliance until all gas leaks have been rectified.
Never complete a gas leak test while smoking.
Note: If there is a leak anywhere on the gas cylinder, do not use the cylinder.
Locate the leaking cylinder outdoors away from sources of ignition, then contact
your local gas authority or cylinder exchange provider to arrange disposal.
Barbecue connection

GAS EMERGENCY
PROCEDURE
A strong gas smell or hissing sound indicates a serious problem with your BBQ or
the LPG gas cylinder. Failure to immediately follow the steps listed below could
result in property damage, serious bodily injury, or even death. If a strong smell of
gas or hissing sound occurs, complete the following steps.
1. Shut off the LPG cylinder valve.
2. Turn the control knobs to OFF position.
3. Put out any flame with a class B fire extinguisher and clear the area of people.
4. Move away from the LPG gas cylinder.
5. Do not try to fix the problem yourself.
If odour continues or you have a fire you cannot extinguish, call the fire
department immediately.
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL34
SStteepp77
Assemble the side panels on the hood by M5 4pcs as shown. Fit the temperature gauge on the
glass.
SSTTOORRAAGGEE
1. Ensure the BBQ is properly cooled.
2. Storage of this gas BBQ indoors is permissible only if the gas cylinder is disconnected and
removed from the BBQ.
3. Store the BBQ in a cool dry place.
4. Always disconnect the gas cylinder and store it in a safe place, never store a gas cylinder on its
side.
5. Never store a gas cylinder in a building, garage or any other enclosed area.
6. If you intend to leave your BBQ outside make sure it is protected from the elements by a
heavy-duty cover (not included).
7. Keep outdoor cooking gas BBQ area clear and free form combustible materials, petrol and
other flammable vapours and liquids.
WWAARRNNIINNGG
SSTTOORREECCYYLLIINNDDEERRIINNAAWWEELLLLVVEENNTTIILLAATTEEDDAARREEAA
OOUUTTOOFFRREEAACCHHOOFFCCHHIILLDDRREENN
WARNING
STORE CYLINDER IN A WELL VENTILATED AREA
STORE CYLINDER OUT OF REACH OF CHILDREN

MATADOR INSTRUCTION MANUAL 7
GENERAL INFORMATION
Note: Before using the BBQ, remove any packaging material within and around
the BBQ supplied for protection during transit.
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating
and maintenance instructions thoroughly before installing or servicing this
equipment.
Strong winds and low temperatures can affect the heating and performance of
your BBQ so factor in these elements when positioning your BBQ outdoors for
cooking.
Never use your BBQ in a garage, porch, shed, breezeway or any other enclosed
area. Your BBQ is to be used outdoors only,. Do not obstruct the flow of
ventilation air around the BBQ. This BBQ is not intended to be installed in or on
recreational vehicles and/or boats.
Warning: accessible parts may be very hot. Keep young children away.
Do not move the appliance during use.
Any modification of the appliance may be dangerous.
Do not replace the grill with an extra hotplate. The warranty will become null and
void.
Note: The normal flow of gas through the Regulator and Hose Assembly can
create a humming sound. A low volume of sound is perfectly normal and will not
interfere with operation of the BBQ. If humming sound is loud and excessive you
may need to purge air from the gas line.
Do not store gas cylinders below ground level. LP gas is heavier than air so if a
leak occurs the gas will collect at a low level and could ignite in the presence of a
flame or spark.
You must have the correct gas cylinder, regulator and hose for this BBQ to
operate safely and efficiently. Use of an incorrect gas cylinder, regulator or hose
is dangerous and will void the warranty on this product.
-
-
-
-
-
-
-
-
-
-
-

EXPLODED PARTS VIEW
5
1
14
10
18
20
15
2
37
8
26
24
23
17
13
11
22
16
29
21
12
28
6
27
25
19
30
31
32
33
4
9
34

MATADOR INSTRUCTION MANUAL 9
PARTS LIST
1. Cooking grill x 2 2. Hotplate 3. Warming rack 4. Firebox
5. Flame tamer x 4 6. Left side table 7. Right side
burner table
8. Side burner
trivet
9. Regulator 10. Left side
cabinet panel
11. Crossbeam 12. Bottom
cabinet panel
13. Back cabinet
panel
14. Separation
cabinet panel
15. Left door 16. Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
3 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table 8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
MATADOR INSTRUCTION MANUAL 8
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
3 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
3 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
13 Back panel of cabinet
14 Separation panel of
cabinet 15 Left door
16 Right door
PARTS LIST
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x2
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator 10 Left side panel of
cabinet 11 Crossbeam 12 Bottom panel of
cabinet
3 Back panel of cabinet
14 Separation panel of
cabinet
15 Left door
16 Right door
1 Cooking grill x 2
2 Hotplate
3 Warming rack
4 Firebox
5 Flame tamer x 4
6 Left side table
7 Right side burner
table
8 Side burner trivet
9 Regulator
10 Left side panel of
cabinet
11 Crossbeam
12 Bottom panel of
cabinet
13 车架后板
14 车架隔板
15 车架左门
16 车架右门
Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x 2

21 Castor with lock x2
22 Plastic backing board
23 Control knob
24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup x 2
28 Handle of hood
29 Scraper tool
30 Left door axial
piece-Upper
31 Left door axial
piece-Down
32 Right door axial
piece-Upper
33 Right door axial
piece-Down
34 Base weight
PARTS LIST
17. Right cabinet
panel
18. Side cabinet
panel support x2
19. Magnet plate 20. Castor without
lock x2
21. Castor with
lock x 2
22. Plastic backing
board
23. Control knob 24. Seat of control
knob
25. Grease tray 26. Smoker box 27. Grease cup x2 28. Hood handle
29. Scraper tool 30. Left door
hinge - upper
31. Left door
hinge - lower
32. Right door
hinge - upper
33. Right door
hinger - lower
34. Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2 19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight
Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
Right door hinge -Down 34 Base weight
17 Right side panel of cabinet
18 Side panel support of
cabinet x 2
19 Magnet plate
20 Castor without lock x
2
21 Castor with lock x 2 22 Plastic backing board 23 Control knob 24 Seat of control knob
25 Grease tray
26 Smoker box
27 Grease cup
28 Handle of hood
29 Scraper tool
30 Left door hinge -Upper
31 Left door hinge
-Down
32 Right door hinge
-Upper
33 Right door hinge -Down 34 Base weight

MATADOR INSTRUCTION MANUAL 11
HARDWARE PACK
A
Bolt: M6*12
60 B
Washer: M6
18
C
Spring Washer: M6
18 D
Bolt: M5*10
2
E
Bolt: M4*12
5 F
Nut: M4
3
G
Screwdriver
1 H
Bolt: M4*10
12
I
Bolt: M6*35
2 J
Nut: M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL10
HHAARRDDWWAARREEPPAACCKK
A
Bolt:M6*12
60 B
Washer:M6
18
C
Spring washer:M6
18 D
Bolt:M5*10
2
EBolt:M10*8 5 F Nut:M4 3
G
Screwdriver
1 H Bolt:M4*10 12
I
Bolt:M6*35
2 J
Nut:M6
2

Remove all packaging and transit protection materials from parts before assembly.
Wear gloves during assembly to protect your hands from cuts and abrasions.
Some stages of assembly require a 2 person lift.
ASSEMBLY STEPS
STEP 1
Assemble the base weight (34) on the bottom panel of cabinet (12) by bolt (I) 2pcs
and nut (J) 2pcs and washer (B) 2pcs and spring washer (C) 2pcs as shown.
Assemble the door magnet panel (19) on the bottom panel of cabinet (12) by bolt
(A) 2pcs as shown. Assemble the plastic backing board (22) on the bottom panel of
cabinet (12) by bolt (E) 3pcs and nut (F) 3pcs as shown.
5
Assembly Steps
Remove all packaging and transit protection materials from parts before assembly.
STEP 1
Assemble the base weight (34) on the bottom panel of cabinet (12) by bolt (I) 2pcs and nut (J) 2pcs and washer (B)
2pcs and spring washer (C) 2pcs as shown.
Assemble the door magnet panel (19) on the bottom panel of cabinet (12) by bolt（A）2pcs as shown.
Assemble the plastic backing board (22) on the bottom panel of cabinet (12) by bolt (E) 3pcs and Nut (F) 3pcs as
shown.
STEP 2
Assemble the castor without lock (20) and castor with lock (21) on the bottom panel of cabinet (12) by bolt（A）, spring
washer (C), washer (B) each 16pcs as shown.

MATADOR INSTRUCTION MANUAL 13
STEP 2
Assemble the castor without lock (20) and castor with lock (21) on the bottom
cabinet panel(12) by bolt (A), spring washer (C), washer (B) each 16pcs as shown.
STEP 3
Assemble left door hinge-upper (30) and left door hinge-lower (31) on the left side
cabinet panel (10) and assemble the right door hinge-upper (32) and right door
hinge-lower (33) on the right side cabinet panel (17) by bolt (H) 12pcs.
5
Assembly Steps
Remove all packaging and transit protection materials from parts before assembly.
STEP 1
Assemble the base weight (34) on the bottom panel of cabinet (12) by bolt (I) 2pcs and nut (J) 2pcs and washer (B)
2pcs and spring washer (C) 2pcs as shown.
Assemble the door magnet panel (19) on the bottom panel of cabinet (12) by bolt（A）2pcs as shown.
Assemble the plastic backing board (22) on the bottom panel of cabinet (12) by bolt (E) 3pcs and Nut (F) 3pcs as
shown.
STEP 2
Assemble the castor without lock (20) and castor with lock (21) on the bottom panel of cabinet (12) by bolt（A）, spring
washer (C), washer (B) each 16pcs as shown.
6
STEP 3
Assemble left door axial piece-Upper (30) and left door axial piece-Down(31) on the left side panel of cabinet
(10) and assemble right door axial piece-Upper (32) and right door axial piece-Down (33) on the right side panel
of cabinet (17) by bolt (H) 12pcs.
STEP 4
Assemble left side panel of cabinet (10), back panel of cabinet (13) and right side panel of cabinet (17) on the bottom
panel of cabinet (12) by blot (A) 14pcs as shown.

STEP 4
Assemble left side cabinet panel (10), back cabinet panel (13) and right side
cabinet panel (17) on the bottom cabinet panel (12) by bolt (A) 14pcs as shown.
STEP 5
Assemble side panel cabinet support (18) on the bottom panel by bolt (A) 8pcs as
shown.
STEP 4
Assemble left side panel of cabinet (10), back panel of cabinet (13) and right side panel of cabinet (17) on the bottom
panel of cabinet (12) by blot (A) 14pcs as shown.
STEP 5
Assemble side panel support of cabinet (18) on the bottom panel by bolt (A) 8pcs as shown.
STEP 6
Assemble crossbeam (11) on the cabinet by bolt (A) 4pcs as shown.

MATADOR INSTRUCTION MANUAL 15
7
STEP 5
Assemble side panel support of cabinet (18) on the bottom panel by bolt (A) 8pcs as shown.
STEP 6
Assemble crossbeam (11) on the cabinet by bolt (A) 4pcs as shown.
STEP 6
Assemble crossbeam (11) on the cabinet by bolt (A) 4pcs as shown.
STEP 7
Assemble cabinet separation panel (14) on the cabinet by bolt (A) 4pcs as shown.
8
STEP 7
Assemble separation panel of cabinet (14) on the cabinet by bolt (A) 4pcs as shown.
STEP 8
Assemble left door (15) and right door (16) on the cabinet as shown.

STEP 8
Assemble left door (15) and right door (16) on the cabinet as shown.
STEP 9
Assemble hood handle (28) on the hood by bolt (A) 4pcs as shown.
8
STEP 7
Assemble separation panel of cabinet (14) on the cabinet by bolt (A) 4pcs as shown.
STEP 8
Assemble left door (15) and right door (16) on the cabinet as shown.
9
STEP 9
Assemble handle of hood (28) on the hood by bolt (A) 4pcs as shown.
STEP 10
Assemble firebox (4) on the cabinet by bolt (A) 4pcs as shown.

MATADOR INSTRUCTION MANUAL 17
9
STEP 9
Assemble handle of hood (28) on the hood by bolt (A) 4pcs as shown.
STEP 10
Assemble firebox (4) on the cabinet by bolt (A) 4pcs as shown.
10
STEP 11
Assemble the left side table (6) and the right side burner table (7) on the firebox by bolt (A) 8pcs as shown.
Note: 8pcs screws already in position on firebox sides.
STEP 12
Assemble control knob seat (24) on the side valve by screw (E) 2pcs as shown, put the control knob (23) on the
valve bar as shown.
STEP 10
Assemble firebox (4) on the cabinet by bolt (A) 4pcs as shown.
STEP 11
Assemble the left side table (6) and the right side burner table (7) on the firebox by
bolt (A) 8pcs as shown.
Note: 8pcs screws already in position on firebox sides.

STEP 12
Assemble control knob seat (24) on the side valve by screw (E) 2pcs as shown, put
the control knob (23) on the valve bar as shown.
SSTTEEPP1122
Assemble control knob seat (24) on the side valve by screw (E) 2pcs as shown, put the control
knob (23) on the valve bar as shown.

MATADOR INSTRUCTION MANUAL 19
STEP 13
Assemble the injector bracket by screw (D) 2pcs as shown in photo A and B
Insert the ignition wire as shown in photo C.
MMAATTAADDOORRIINNSSTTRRUUCCTTIIOONNMMAANNUUAALL18
SSTTEEPP1133
Assemble the injector bracket by screw (D) 2pcs as photo A and B shown.
Insert the ignition wire as photo C shown.

STEP 14
Insert the grease cup (27) and smoker box (26) on the control panel as shown.
11
STEP 13
Assemble the injector bracket by screw (D) 2pcs as photoAand B shown.
Insert the ignition wire as photo C shown.
A
B
C
STEP 14
Insert the grease cup (27) and smoker box (26) on the control panel as shown.
STEP 15
Insert the flame tamers (5) on the firebox as shown.
12
STEP 15
Insert the flame tamer (5) on the firebox as shown.
STEP 16
Insert the cooking grill (1) and hotplate (2) on the firebox as shown.