Matador Supernova 4 User manual

CONTENTS 
FEATURES 3
IMPORTANT GAS AND SAFETY INSTRUCTIONS 4
OPERATING PROCEDURE 8
COOKING TIPS 11
CARE AND MAINTENANCE 12
BARBEQUE ASSEMBLY INSTRUCTIONS 14
PARTS DIAGRAM 15
ASSEMBLY INSTRUCTIONS 17
WARRANTY
CONTACT INFORMATION
For spare parts order from your nearest
Burnings Warehouse.
Australia: For service and warranty queries please call
08 9248 9822 or email: [e-mail]
New Zealand: For service and warranty queries please
go to your local Bunnings Warehouse or call 09 978 2200,
fax [phone] or email mar[email protected]
YOU「purchase receipt is required for all warranty claims.
www.matadorbbqs.com.au

INCLUDED IN YOUR BBQ
MATADOR INSTRUCTION MANUAL 3
LengthWidthHeight
Hood840 mm650 mm300 mm
Cabinet1460 mm650 mm1205mm
FEATURES
■4 stainless steel burners
■Enamelled cast iron hotplate & grill
■Warming rack
stainless steel
hood
stainless steel
control plate
Control knobs
for eash burner
Side burner
BARBEQUE DIMENSIONS

HARDWARE PACK LIST
(A)Bolt M6 x 15mm -- 74 pieces
(B)Bolt M4 x 10mm - -- 4 pieces
(C)Lock washer M6 -- 50 pieces
(D)Flat washer M6 ----50 pieces
(E) Flat washer M4------2 pieces
(F) Spanner -------1 piece
(G) Cotter ------------2 pieces
(H) Screwdriver ------------1 piece
TIPS
BEFORE YOU START
zCheck the box and make sure you
have all the parts and fittings listed.
zWhen you are ready to start, make
sure that you have the right tools
in hand, plenty of space and a
clean dry area for assembly.
zUsing knife or box cutter, cut open
carton.
zLay out all bolts and check lengths
before assembly. It is recommended
that the carton is cut open and spread out on the floor and used as a protective
surface during assembly. Refer to the assembly diagrams as necessary.
zRemove all packaged parts from the inside of the grill body before assembling.
zThis product is for OUTDOOR USE ONLY.
zNEVER use indoor, in an enclosed area or below ground level.
zNEVER use an adjustable regulator with this grill. Use only the pressure
regulator and hose supplied.
BARBEQUE ASSEMBLY
INSTRUCTIONS
TOOLS NEEDED FOR ASSEMBLY
• 1 x Screwdriver
• 1 x Adjustable Spanner
• Liquid Nails (not included)
Note: Please use “Liquid Nails” to
bond the granite top and the BBQ
body. (Ensure surfaces to be bonded
are free from all oil, grease and dust).
B.Bolt M4 x 10mm
4 pieces
A.Bolt M6 x 15mm
74 pieces
D.Flat washer M6
50 pieces
C.Lock washer M6
50 pieceS
E.Flat washer M4
2 pieces
H.screwdriver 
1 piece
F. Spanner
1 piece
G. cotte
r
2 pieces
zNOTE: Two people are required for assembly.

PARTS DIAGRAM
FOR HS-BI002
1.Cart leg asm LR
2 pieces
2.Cart Connect
pipe L
5 pieces
3. Cart leg asm M
1 piece
4. Cart connect
pipe LD
1 piece
5. Cart connect
pipe RD
3 pieces
6. Cart connect
pipe RB
1 piece
7.cart table
support plate
1 piece
8.warming grid
1 piece
9. Body asm
1 piece 10.side burner
asm
1 piece
11.knob support
1 piece 12.knob 1 piece
13.side burner
1 piece 14. side grid 1 piece 15. cooking plate 1 piece 16.cooking grid 1 piece
MATADOR INSTRUCTION MANUAL 15

+
17.cart connect
pipe RF
1 piece
18.body table
plate-L
1 piece
19. body table
plate-R
1 piece
20. body table
plate-B
1 piece

ASSEMBLY
INSTRUCTIONS
Remove all contents from packaging, and make sure all parts are present before
attempting to assemble! Tighten all bolt connections by hand first, then when the BBQ is
fully assembled, go back and tighten.
STEP 1
Assemble the Cart
connect pipe L (Part 2)
to the Cart leg asm
LR (Part1) and Cart
leg asm M (Part3)
as shown. Use the
Bolt A, lock washer C,
Flat washer D and tighten.
STEP 2
Assemble Cart connect
pipe LD (part 4) to
the Cart connect pipe
L as shown. Use the
Bolt A, lock washer C,
Flat washer D and tighten.
MATADOR INSTRUCTION MANUAL 17

STEP 3
Assemble the Cart connect pipe L
(Part 2) to the Cart leg asm LR
(Part1) and Cartleg asm M (Part3)
as shown.Use the Bolt A,lock washer C,
Flat washer D and tighten.







STEP 4
Assemble the Cart connect
pipe RD (Part 5) to the Cart
leg asm LR (Part1) and Cart leg
asm M as shown.Use the
Bolt A, lock washer C, Flat
washer D and tighten.
















STEP 5
Assemble the Cart connect
pipe RB (Part 6) and cart
connect pipe RF(Part 17)
to the Cart leg asm LR and
Cart leg asm M as shown.
Use the Bolt A, lock washer C,
Flat washer D and tighten.


















STEP 6
Assemble the cart table
support plate ( part 7 )
to the cart asm as shown.
Use the Bolt A, lock washer
C, Flat washer D and tighten.







MATADOR INSTRUCTION MANUAL 19







STEP 7
Take out the side burner
asm ( part 10) from body
asm as shown.
STEP 8
Assemble the body table
plate-L( part 18) and body
table plate-R( part 19) to
the body asm as shown.
Use the Bolt A and tighten.






