Matsing MS-18F45 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam And Connector Layout
Beam 1 to Beam 6 (Row 1)
Beam 7 to Beam 12 (Row 2)
Beam 13 to Beam 18 (Row 3)
Connector Details
Connector Ports Table
BEAM PATTERN
Horizontal Beam Pattern
Row 1 & Row 3 Pattern
Row 2 Pattern
Vertical Beam Pattern
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 7
1.11
1.12
1.13
1.20
2.00
2.11
2.12
3.00
3.10
3.30
3.40
3.41
3.42
3.43
email:
website:
Page
Revised by
Revision
nos.
Description
Date
3.31
2.10
2.20
3.20
1.30
11 Jun 2021
Ray Ling
Pavel
MS-18F45-IM-001
1.00
1.10
00
INSTRUCTION MANUAL MS-18F45
MS-18F45
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision

BEAMS & CONNECTORS:
Plan View Resultant Beam And Connector Layout
Beam 1 to Beam 6 (Row 1)
Beam 7 to Beam 12 (Row 2)
2 / 7
1.11
1.12
Page
1.00
1.10

Beam 13 to Beam 18 (Row 3)
Connector Details
Connector Ports Table
Page 3 / 7
1.13
1.20
1.30

BEAM PATTERN
Horizontal Beam Pattern
Row 1 & Row 3 Pattern
Row 2 Pattern
Vertical Beam Pattern
4 / 7
2.10
2.11
2.12
2.20
2.00
Page

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
5 / 7
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transporting of large or heavy equipment.
Appropriate material handling machine should be used. (Risk Assessment applies for Forklift or
Pallet Truck Lifting)
45, 60,90,120 (cm) Lens
4
M12 x 16cm
8
Page
Lens Size (Model)
Bracket
Qty (pc)
Bolt & Nuts
Size
Bolts Set
(pc)
180 (cm) Lens
6
M14 x 16cm
12
3.20
3.00
3.10
Important Notes:
End User is required to CUSTOM-MAKE the additional supporting bracket and tighten it
Tighten to
the
pole with
Bolt
& Nuts Sets

Installation using a crane
Lifting the Antenna
6 / 7
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling
machine should be used and only certified personnel should perform the task. (Risk
Assessment requirement applies for both Up-Lifting and Down-Lifting.)
3.30
3.31
Page
Using cable, rope or sling belt to cross over frame base 4 main area to the top and grouping
by securing with fastener.

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
7 / 7
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree)
with ≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
With reference to Item 3.20 Bracket Mounting, End user is required to Custom-Make the
additional supporting bracket and tighten it to the existing Antenna bracket to meet the
deployment needs.
3.41
3.42
3.43
Page
3.40