Matsing MS-18H90 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Beam 1 to 6 (Row 1), Beam 13 to 18 (Row 3)
Beam 7 to 12 (Row 2)
Plan View Connector Layout
Connector Ports Table
BEAM PATTERN
Vertical Beam Pattern (Top & Bottom Row)
Horizontal Beam Pattern (Row 1 & Row 3)
Horizontal Beam Pattern (Row 2)
TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
Installation using a crane
Lifting the Antenna
Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
Revision History:
[email protected] www.matsing.com 1 / 7
1.30
1.20
1.12
1.00
1.10
1.11
3.20
3.00
3.10
2.30
2.20
2.00
2.10
3.40
3.41
3.42
3.43
3.30
3.31
email:
website:
Page
Revision
nos.
17 Jun 2021
Bracket installation update
RayLing
01
30 Sep 2021
General revision and update
RayLing
02
Date
Description
Revised by
30 Sep 2021
Ray Ling
Pavel
MS-18H90-IM-001
2
INSTRUCTION MANUAL MS-18H90
MS-18H90
Instruction Manual
Date
Prepared by
Approved by
Document nos
Revision

BEAMS & CONNECTORS:
Plan View Resultant Beam Direction
Beam 1 to 6 (Row 1), Beam 13 to 18 (Row 3)
Beam 7 to 12 (Row 2)
2 / 7
1.00
1.10
1.12
1.11
Page
0
Frequency: 1695 MHz
Plan View Resultant Beam Directions
BEAM 1 - 6
(Row 1)
BEAM 13 - 18
(Row 3)
0
Frequency: 1695 MHz
Plan View Resultant Beam Directions
BEAM 7 - 12
(Row 2)

Plan View Connector Layout
Connector Ports Table
BEAM PATTERN
Vertical Beam Pattern (Top & Bottom Row)
Page 3 / 7
2.10
(-45
(+45
(-45
(+45
(-45
2.00
PORT 28
PORT 25
PORT 26
(+45
(-45
(+45
(-45
(+45
(-45
(+45
BEAM 13
PORT35
PORT 36
PORT 33
PORT 34
PORT 31
PORT 32
PORT 29
PORT 30
PORT 27
(+45
(-45
(+45
(-45
Row 3
BEAM 18
BEAM 17
BEAM 16
BEAM 15
BEAM 14
PORT 13
PORT 14
(+45
(-45
(+45
(-45
(+45
(-45
(+45
(-45
PORT 19
PORT 20
PORT 17
PORT 18
PORT 15
PORT 16
(-45
Row 2
BEAM 12
BEAM 11
BEAM 10
BEAM 9
BEAM 8
BEAM 7
(-45
(+45
(-45
(+45
(-45
(+45
PORT 11
(+45
(-45
(+45
(-45
(+45
1.30
Row 1
BEAM 6
BEAM 5
BEAM 4
BEAM 3
BEAM 2
BEAM 1
PORT 6
PORT 3
PORT 4
PORT 1
PORT 2
PORT 12
PORT 9
PORT 10
PORT 7
PORT 8
PORT 5
PORT 23
PORT 24
PORT 21
PORT 22
1.20
PLAN VIEW CONNECTOR LAYOUT
MS-18H90

Horizontal Beam Pattern (Row 1 & Row 3)
Horizontal Beam Pattern (Row 2)
4 / 7
2.20
2.30

TRANSPORTATION / INSTALLATION
Transportation (From Point to Point)
Bracket Mounting
5 / 7
1
30cm to 120cm
Ø13mm x 8
Bracket Qty
4
OPEN end bolt & nuts sets
M12 x 15cm=8sets
Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and
Measure when moving and transportation of large or heavy equipment, appropriate material handling
machine should be use. (Risk Assessment apply for Forklift or Pallet Truck Lifting)
Item
Lens/Types
Holes Size
3.00
3.10
3.20
Important Notes:
End User is require to
Custom-Make
the additional
supporting bracket
and tighten to the
existing Antenna
bracket to meet the
deployment needs.
Attached the bracket
tighten with specified
bolts sets.

Installation using a crane
Lifting the Antenna
6 / 7
(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)
3.31
The antenna has 2 hook points installed on the top frame (located slightly behind the center of the
sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be
securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.
3.30
Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and
Measure when performing lifting of large or heavy equipment, appropriate material handling machine
should be used and only certified personnel should perform the task.

Antenna Installation
Antenna Leveling
Digital Level Gauge Calibration
Adjustment Requirement
7 / 7
After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with
≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)
3.42
3.43
3.40
3.41
With reference to Item 5.2 Bracket Mounting Procedure, End user is required to Custom-Make the
additional supporting bracket and tighten it to the existing Antenna bracket to meet the deployment
needs.