Matsing MS-MBA-3-H4 User manual

TABLE OF CONTENTS:
BEAMS & CONNECTORS:
Plan View Resultant Beam Layout
Connector Ports Table
Connector Detail
Connector Layout
PATTERN DIAGRAM
Frequency: 1695 - 2690 MHz
Horizontal Pattern
Vertical Pattern
MANUAL TILT ADJUSTMENT
BRACKET INSTALLATION
Bolts & Nuts Requirements
Bolts & Nuts
Bracket
Tools Requirement
Adjustable Spanner
M12 Spanner
Bracket Spacing &
Installation Sample
Revision History:
[email protected] www.matsing.com 1 / 5
email:
website:
Page
07-Apr-21
To include the bracket installation process.
Ray Ling
1
Date
Description
Revised by
Revision
nos.
4.20
4.21
4.22
4.30
2.12
3.00
4.00
4.10
4.11
4.12
1.20
1.30
1.40
2.00
2.10
2.11
Pavel
MS-MBA-3-H4-IM-001
1
INSTRUCTION MANUAL MS-MBA-3-H4 (MBA-4)
1.00
1.10
MS-MBA-3-H4 (MBA-4)
Instruction Manual
Date
Prepared by
Approved by
Document nos
Rev
7 Apr 2021
Ray Ling

BEAMS & CONNECTORS:
Plan View Resultant Beam Layout Connector Ports Table
Connector Layout
Connector Detail
2 / 5
1.40
1.30
Page
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
Port 9
Port 10
Port 5
Port 6
Port 1
Port 2
(+45˚)
(-45˚)
(+45˚)
(-45˚)
(+45˚)
(-45˚)
Port 11
Port 12
Port 7
Port 8
Port 3
Port 4
1.00
1.10
1.20
MS-MBA-3-H4 (MBA-4)
Connector Table
BEAM 3
BEAM 2
BEAM 1
Port 1 (+45˚)
Port 6 (-45˚)
Port 3 (+45˚)
Port 5 (+45˚) Port 7 (+45˚)
Port 9 (+45˚) Port 11 (+45˚)
Port 12 (-45˚)
Port 10 (-45˚)
Port 8 (-45˚)
Port 4 (-45˚)
Port 2 (-45˚)
REAR VIEW CONNECTOR LAYOUT
MS-MBA-3-H-4
(MBA-4)
AISG IN
HB Beams: 1,2,3
HB Ports: 1 to 12
BEAM 1BEAM 2BEAM 3

PATTERN DIAGRAM
Frequency: 1695 - 2690 MHz
Horizontal Pattern
Vertical Pattern
3 / 5
2.11
2.12
Page
2.00
2.10
MS-MBA-3-H4 (MBA-4) 1695 - 2690 MHz
Frequency:
BEAM 2


1695 - 2690 MHz
Frequency:
MS-MBA-3-H4 (MBA-4)

MANUAL TILT ADJUSTMENT
BRACKET INSTALLATION
Bolts & Nuts Requirements
Bolts & Nuts Bracket
4 / 5
10
4.11
4.12
Page
1
All MBA's Antennas
2
M12 x
200mm
4
M12
nos
Model Apply
Bracket
Bolts
Nuts
Qty
Size
Qty
Size
Qty
2
By Default the knob is on engaged mode, pull out the handle for manual tilt
adjustment, turn the handle to change the tilt.
3
When done, push the handle back in, screw the waterproof cap back to the position.
4.00
4.10
3.00
1
The MBA antenna come in RET mode as default, but if needed can also be manually
adjusted. To do so, please unscrew the waterproof cap behind the element whose tilt
is to be adjusted.
Unscrew/
Screw the cap for tilt
adjustment process
Engaged with internal RET
motor position
Pull knob out to
disengaged RET for
tilt adjustment
RET
Controller
Angle
Indicator
Tilt
Adjustment
Knob

Tools Requirement
Adjustable Spanner
M12 Spanner
Bracket Spacing &
Installation Sample
5 / 5
4.30
Page
4.20
4.21
4.22