Matsusada R4G Series User manual

F-RA-001-2R3
Instruction manual
MODEL R4G/R4GE series
B/N: 217.9.138 *217.9.138*Rev. 0.8

Trademarks
◆Company names and product names in this document are the trademarks or registered
trademarks of their respective companies.
Note
◆All rights reserved.
◆
No part of this publication may be reproduced, stored in a retrieval system, or transmitted,
in any form, or by any means, mechanical, electronic, photocopying, recording, or
otherwise, without the prior written permission of Matsusada Precision.
◆
No patent liability is assumed with respect to the use of the information contained herein.
Moreover, because Matsusada Precision is constantly striving to improve its high-quality
products, the information contained in this manual is subject to change without notice.
Every precaution has been taken in the preparation of this manual. Nevertheless,
Matsusada Precision assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information
contained in this publication.
Warranty
◆For details, refer to the following website.
https://www.matsusada.com/support/manufacturer_warranty.html

i
R4G/R4GE series
For Safe Use of the Product
◆Introduction
The product generates high-voltage and high-energy.
Therefore, wrongly handling or operating the product may result in death or serious injury and maybe
property damage as well. In order to use the product safely, read the instruction manual thoroughly before
use to understand how to use and operate it properly.
Please note that we will not be held responsible for any damage or loss caused by not following the
warnings, cautions, and procedures described in the manual.
Keep the manual with you so that you can read it whenever you want.
◆Symbols
Symbols are used in the manual and product, which indicate precautions to be observed for safe use.
Understand these symbols first and then read the manual thoroughly.
Some symbols below are not used in products.
Indicates a potentially hazardous situation, which, if not avoided, may
result in serious injury or death.
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury or in property damage.
Indicates danger/warning/caution. Refer to
the instruction manual when this symbol
appears on the unit.
Frame or chassis terminal
Indicates the possible danger of electric
shock under specific conditions, which may
result in serious injury or death.
Ground terminal
High Temperature Caution:
Indicates the possible danger of injury by
high temperature under specific conditions.
Power ON
Indicates general prohibitions, including
warnings.
Power OFF
Indicates what must be followed.
Standby: Voltage is being
applied to the inside of the
product.
Protective earth terminal (ground terminal
for preventing electric shock)
Bistable push button switch
ON
Indicates the possible danger of death if you
drink it and burns or blindness if it attaches.
Bistable push button switch
OFF
Indicates the possible danger of exposure
to radiation.
Alternative Current

ii
R4G/R4GE series
Understand the risks.
The Product generates high-voltage and high-energy.
The product is designed for electrical engineers or the equivalents who install, wire, and operate it.
Read the instruction manual thoroughly before use and familiarize yourself with the proper use and
danger of the product.
Make sure to allow only specific people to handle the product.
Make sure to allow only the following people to handle the product:
1. who are electrical engineers or the equivalents and have already familiarized themselves with the
proper use and danger of the product, or
2. who are electrical engineers or the equivalents and have already been trained by the
above-mentioned people, or
3. who work under the supervision of the above-mentioned people.
If people other than those listed above install, wire, or operate the product, it may cause electric
shock, burnout, or injury.
Do not open or remove the case or panel of the product.
Do not disassemble, repair, or modify the product by yourself. High-voltage is applied to the inside of it.
Otherwise, it may cause electric shock, fire, or malfunction.
Moreover, if you do it, the safety and functions are not covered with the warranty.
The product does not suit to install and use in places where children may be present.
The product is designed to be installed in places such as factories or laboratories. Do not install and use it
where children may be present.
Make sure to ground it.
When the product has a protection ground terminal or GND terminal, make sure to ground it.
When the AC line input of it is an inlet type, connect the attached power cable or a power cable suitable for
your area to an outlet with the ground. Otherwise, it may result in electric shock or fire.
Regarding power cable
When a power cable is enclosed or attached to the product, do not use it for other products.
When no power cable is enclosed with the product, prepare the power cable suitable for the usage
environment and area by yourself.
Regarding the connection of power cable
Electrical engineers or the equivalents who have already been familiarized with the proper use and danger
of the product should connect the power cable to the AC input by referring to the instruction manual.
Regarding products that have acquired the safety standard, check the page describing the over-voltage
categories too.
Do not process or damage power cables
It may result in electric shock or fire.
Regarding the input voltage
Check the page describing the input terminals and input voltage in the instruction manual.
Do not provide any voltage out of the specifications.

iii
R4G/R4GE series
Regarding the fuse
The product builds in a protective fuse. In the case where a fuse holder is arranged outside of the product,
you can replace it by yourself. Refer to the instruction manual to replace it.
In the case where a fuse holder is not arranged outside of the product, you cannot replace it by yourself.
In this case, do not open the case or panel of the product and contact us.
The product is designed for indoor use.
Use the product indoors only, not outdoors. Even indoors, do not use it if there is a possibility of water
leakage, flooding, or snow covering.
Regarding operating temperature and humidity
Use the product within the range of the specifications describing in the instruction manual.
Do not use it in a place where the ambient temperature exceeds the specified range or a closed place.
Do not install the product in places where condensation may occur.
Otherwise, insulation deteriorates and it may cause electric shock, fire, or malfunction.
Do not place anything on top of the product.
Otherwise, they may fall or tumble from it.
Do not put anything into the product.
Do not put foreign objects such as metal or liquid into the product through the air inlets, air outlets, or other
openings. Otherwise, it may result in electric shock, fire, or malfunction.
Operate the product with the right hand.
Use only your right hand to operate the product and keep your left hand away from it, which can reduce
the risk of electric current flowing through the left hand to the vital organs of the body in the event of an
electric shock.
Do not touch the wiring/load connected to the output and any terminals/connectors during the
operation or just after turning output off.
Very high-voltage is on the terminals and connectors during the operation and even just after the output is
turned off. Touching them may result in serious injury or death by electric shock.
The terminals here mean all terminals like input and output terminals and terminals for communications
and remote controls.
Turn off the product before touching the wiring/load connected to the product and any
terminals/connectors on the product and cut it off from the AC input.
Before touching the terminals/connectors and wiring/load, turn off the product and unplug the AC input
cable from the outlet or turn off the AC input breaker. Then, check there is no voltage remained using a
tester.
Since the output and sense terminals are connected to condensers in it, there is high-voltage remained on
them even just after it is turned off.
In order to avoid electric shock, ground the terminals to discharge using a short-circuit grounding
apparatus and check the voltage again.
The terminals here mean all terminals like input and output terminals and terminals for communications
and remote controls.

iv
R4G/R4GE series
Level the product out to use for good heat dissipation.
Do not install the product upside down or sideways. If not, the inner heat dissipation will be insufficient.
It may result in smoke or fire due to components deterioration.
Do not install the product in a place where cold air directly blows to it.
It may result in electric leakage or burnout due to condensation.
Do not install the product in a place where it is exposed to corrosive gases or liquids.
It may result in smoke or burnout due to components deterioration.
Do not store or use the product in a place where conductive dust, such as iron power, can enter
through the air inlet/outlet.
Doing so may cause a short circuit, resulting in electric leakage, burnout, fire, or malfunction.
Do not install the product in a dusty place.
Accumulating dust in the air inlet will make hard to cool it down it, it may result in malfunction.
In that case, remove dust immediately.
Do not block the air inlet and outlet.
Secure 30 cm space at least around the openings.
If they are blocked, the product cannot show the rated performance due to the internal temperature
increase. Moreover, components deteriorate and it may result in smoke or fire.
Remove wiring to and from the product when work like welding near it is done.
Do not wipe the equipment with a dust cloth wet with chemicals (thinner or the like) or water.
Otherwise, it may result in an electric shock, electric leakage, or burnout due to water getting inside.
Regarding fan replacement
When products equip a fan, it has a lifetime. It will be worn out and deteriorated with the time passed and
its operation may become unstable. Also, its lifetime greatly varies depending on the usage environment
such as temperature, humidity, dust. It requires to be replaced at regular intervals to extend the lifetime.
For the replacement, contact us.
(It requires a replacement charge separately. Do not replace it by yourself, as there is a risk of electric
shock.)

Table of Contents
v
R4G/R4GE series
Table of Contents
Page
For Safe Use of the Product ............................................................................................................................................................................... i
Table of Contents ..................................................................................................................................................................................................... v
1 Introduction···········································································································································································································1
1-1 Introduction··································································································································································································1
1-2 Overview·······································································································································································································1
1-3 Features········································································································································································································1
1-4 Lineup·············································································································································································································2
1-5 Specifications·····························································································································································································3
2 Before Use············································································································································································································5
2-1 Unpacking····································································································································································································5
2-2 Initial Inspection························································································································································································5
2-3 Precautions for handling·······································································································································································5
2-4 Installation····································································································································································································6
2-4-1 Installation Conditions··································································································································································6
2-5 External View······························································································································································································7
2-5-1 Front Panel························································································································································································7
2-5-2 Rear Panel·························································································································································································8
2-6 External Dimensions (Unit: mm):·····················································································································································9
2-6-1 Width: 84 mm····················································································································································································9
2-6-2 Width: 105 mm·············································································································································································· 10
2-6-3 Width: 210 mm·············································································································································································· 11
2-7 Remote Interface Connector (TB1) and Function Setting Switch (SW1)·································································12
2-7-1 Remote Interface Connector (TB1)···································································································································· 12
2-7-2 Function Setting Switch (SW1)············································································································································· 13
2-8 When Connecting a Load with Accumulated Energy········································································································· 13
3 Basic Operation to Output·········································································································································································· 14
4 Normal Operation··························································································································································································· 15
4-1 Operating Mode Description···························································································································································· 15
4-1-1 Constant Voltage (CV) Mode················································································································································ 15
4-1-2 Constant Current (CC) Mode················································································································································ 15
4-1-3 Crossover Mode··········································································································································································· 15
4-2 Output ON/OFF······················································································································································································ 16
4-3 Presetting the Output Voltage and Output Current·············································································································· 16
4-4 OVP (Overvoltage Protection) and OCP (Overcurrent Protection)············································································· 16
4-5 LOCK··········································································································································································································· 19
4-6 Power Failure Protection··································································································································································· 20
4-7 Last Setting Memory············································································································································································ 20
4-8 -LS (Remote Switch) ON/OFF (only for R4G series)·········································································································· 21
4-9 -LD (Interlock) (only for R4G series)··········································································································································· 23
4-10 Remote Sensing (only for R4G series)···································································································································· 24
4-11 Error List·································································································································································································· 24

Table of Contents
vi
R4G/R4GE series
Page
5 Basic Operation······························································································································································································· 25
5-1 Single Operation···················································································································································································· 25
5-2 Series Operation···················································································································································································· 25
5-3 Parallel Operation················································································································································································· 26
6 Useful Features······························································································································································································· 27
6-1 Master/Slave Setting (R4G series with the -LGmb option)················································································································ 27
6-1-1 Description of Master/Slave Function······························································································································· 27
6-1-2 Master/Slave Connection························································································································································ 28
6-2 Multi-set Function (only for R4G series) ·············································································································································· 29
6-3 Startup Menu··························································································································································································· 31
6-3-1 Setting the Startup Menu························································································································································· 31
6-4 Each Menu Mode·················································································································································································· 33
6-5 Startup Menu List·················································································································································································· 37
6-6 Delay Trigger Function······································································································································································· 38
6-6-1 Useing the Delay Trigger Function····································································································································· 38
6-6-2 Stopping the Delay Trigger in an Emergency··············································································································· 38
6-6-3 Using the Delay Trigger Function in Master/Slave Configuration (R4G series with -LGmb Option)················ 38
7 Analog Control·································································································································································································· 41
7-1 Local Programming Mode Operation·········································································································································· 41
7-2 Switching Local/Remote Mode (Voltage/Current Mode Setting)·················································································· 41
7-3 Remote Programming········································································································································································· 42
7-3-1 Voltage Program Setting with External Voltage··········································································································· 43
7-3-2 Voltage Program Setting with External Resistance··································································································· 43
7-3-3 Current Program Setting with External Resistance··································································································· 44
7-3-4 Current Program Setting with External Resistance··································································································· 44
7-4 Monitor and Status Outputs····························································································································································· 45
7-4-1 Monitor Output·············································································································································································· 45
7-4-2 Status output·················································································································································································· 45
7-5 Parallel Operation················································································································································································· 47
7-6 Introduction of Pressure Welding Connector Tools············································································································· 49
8 Troubleshooting······························································································································································································· 50

1 Introduction
1 R4G/R4GE series
1Introduction
1-1 Introduction
Thank you very much for purchasing our R4G/R4GE series, the ultra-low noise programmable DC
power supply units.
We have taken all possible measures to ensure the quality control of our products. Please follow
the instructions in this manual to ensure full performance and safe use of the product.
We have applied our best to prepare this instruction manual, but if you find any unclear points, errors,
or missing contents, please contact us.
1-2 Overview
The R4G/R4GE series are high precision, ultra-low noise DC power supply units adopting series regulator
technology, which have two 4-digit meters and high-resolution D/A* and A/D converters enabling you to
set and read the output values finer.
Since the series are equipped with not only overvoltage protection but also overcurrent protection as
standard, moreover support digital communication as well, the series can be used in a wide range of
applications from experiments to automation lines.
* R4GE series is not equipped with D/A converters.
1-3 Features
Voltage and current display with 4-digit indicators
Despite its small size, voltage and current are indicated in 4-digit. Possible to control in units of
"10mV" and "0.1mA"*.
* Model-dependent.
Ultra-low ripple and fast response
Ultra-low ripple, low-noise, and fast response by adopting a series regulator technology.
Various functions equipped as standard
Useful features such as overvoltage protection, overcurrent protection,
and key lock are provided as standard.
Not noisy because of the natural air-cooling system adopted (108W or lower
models)
Its operating sound is quiet due to no cooling fan.
Digital interfaces are also supported. (only for R4G)

1 Introduction
2 R4G/R4GE series
1-4 Lineup
Model
Output
Voltage
[V]
Output
Current
[A]
Output
power
[W]
Minimum setting unit
Power
consumption
[VA]
Weight
[Kg]
Output voltage
[mV]
Output current
[mA]
R4G/E6-2
0 to 6
0 to 2
12
1
1
30
Approx. 3
R4G/E8-5
0 to 8
0 to 5
40
1
1
90
Approx. 6.5
R4G/E18-2
0 to 18
0 to 2
36
10
1
90
Approx. 3
R4G/E18-3
0 to 18
0 to 3
54
10
1
100
Approx. 6.5
R4G/E18-5
0 to 18
0 to 5
90
10
1
170
Approx. 6.5
R4G/E18-10
0 to 18
0 to 10
180
10
10
300
Approx. 8
R4G/E36-1
0 to 36
0 to 1
36
10
1
90
Approx. 3
R4G/E36-3
0 to 36
0 to 3
108
10
1
200
Approx. 6.5
R4G/E36-5
0 to 36
0 to 5
180
10
1
300
Approx. 8
R4G/E45-2
0 to 45
0 to 2
90
10
1
170
Approx. 6.5
R4G/E45-4
0 to 45
0 to 4
180
10
1
300
Approx. 8
R4G/E60-1.2
0 to 60
0 to 1.2
72
10
1
130
Approx. 6.5
R4G/E80-1
0 to 80
0 to 1
80
10
1
130
Approx. 6.5
R4G/E120-0.3
0 to 120
0 to 0.3
36
100
0.1
100
Approx. 6.5
R4G/E120-0.6
0 to 120
0 to 0.6
72
100
0.1
160
Approx. 6.5
R4G/E160-0.45
0 to 160
0 to 0.45
72
100
0.1
160
Approx. 6.5
R4G/E250-0.3
0 to 250
0 to 0.3
75
100
0.1
170
Approx. 6.5
R4G/E360-0.2
0 to 360
0 to 0.2
72
100
0.1
160
Approx. 6.5
R4G/E650-0.1
0 to 650
0 to 0.1
65
100
0.1
140
Approx. 6.5

1 Introduction
3 R4G/R4GE series
1-5 Specifications
Item
Description
Input voltage
120Vac±10%, 50/60Hz, single phase
Output control
(voltage &
current)
R4G series:
Local: Rotary encoder on the front panel
Remote: External control voltage: 0 to 10Vdc or external resistance: 0 to 10kΩ
R4GE series:
Rotary encoder on the front panel
Stability
0.05% of max. output voltage/8H
Temp. coefficient
0.01%/°C (Typ.) of max. output voltage, 0.02%/°C (Typ.) of max. output current
Output display
Output voltage: 4-digit digital indicator, accuracy ±0.3% rdg. + 2-dgt.
Output current: 4-digit digital indicator, accuracy ±0.5% rdg. + 3 dgt.
Protection circuit
Overvoltage protection (OVP), Overcurrent protection (OCP),
Power failure protection (PFP)
Other functions
Common to R4G/R4GE series: Key lock to prevent accidental operation, Last setting
memory
R4G series: ON/OFF by Remote switch, Remote sensing, Status signal output, Delay
trigger function, Multi-set function
Transient
response time
Recovery time: 50μs (at 10%⇔100% load regulation)
Operating
temperature
0℃to +40℃
Storage
temperature
-20℃to +70℃
Storage humidity
20% to 80% (no condensation)
Withstand voltage
Between input and output terminals and between input terminals and chassis:
AC1000V/1 min.
Voltage to ground
Models with the output voltage of 80 V or lower: ±250 V-DC
Models with the output voltage of 120 to 360 V: ±500 V-DC
Models with the output voltage of 650V: ±650V-DC
(“+”or “-“terminal grounding possible)

1 Introduction
4 R4G/R4GE series
Operating characteristics
Model
Constant voltage characteristics
Constant current characteristics
Ripple
[mVrms]
Input
regulation
[mV] *1
Load
regulation
[mV] *2
Ripple
[mVrms]
Input
regulation
[mV] *1
Load
regulation
[mV] *2
R4G/E6-2
0.5
1
5
1
2
10
R4G/E8-5
0.5
1
5
1
4
20
R4G/E18-2
0.5
1
2
1
2
10
R4G/E18-3
0.5
1
3
1
2
15
R4G/E18-5
0.5
1
5
1.5
4
20
R4G/E18-10
1
2
10
3
5
25
R4G/E36-1
0.5
2
2
1
2
10
R4G/E36-3
0.5
2
4
1
2
15
R4G/E36-5
0.5
2
4
1
2
15
R4G/E45-2
1
4
4
2
2
15
R4G/E45-4
1
4
4
5
5
20
R4G/E60-1.2
1
4
4
1
2
10
R4G/E80-1
1
4
4
1
2
10
R4G/E120-0.3
1
7
7
1
2
10
R4G/E120-0.6
1
7
7
1
2
10
R4G/E160-0.45
2
10
10
1
2
10
R4G/E250-0.3
3
15
15
1
1
5
R4G/E360-0.2
3
25
25
1
1
5
R4G/E650-0.1
8
30
30
1
1
5
*1 For AC±10% regulation
*2 For load regulation from 10 to 100%

2 Before Use
5 R4G/R4GE series
2Before Use
2-1 Unpacking
After unpacking the box, check that the following accessories are supplied with the product. If the
accessories are different, missing, or broken, please contact us immediately.
<Accessories>
□
Instruction manual
1 ㍶
□
AC input code, three-core, single-phase
1 pc
□
MIL 26-pin male connector*
1 pc
□
MIL 26-pin semi-cover*
1 pc
□
CO-M cable, 2m long*
1 pc
When the -LGmb option is installed.
□
CO-OPT cable*
1 pc
When the -LGob option is installed.
* only for the R4G series
2-2 Initial Inspection
After unpacking and before wiring input and output, check the product for any abnormalities.
Check the front panel, rear panel, and chassis for scratches, dents, or other signs of shock from
transportation or handling.
If you find any abnormalities, please contact the carrier and us.
2-3 Precautions for handling
For the input voltage, check this instruction manual and the indication on the rear panel of the unit
itself.
Do not provide any voltage out of the specifications. Doing so may result in fire or malfunction.
Do not open or remove the case cover of the unit. Doing so may result in electric shock or
malfunction.
When changing the system, do it after turning off the power of all devices that
make up the system.
Generally, connect one of the output terminals, +/-, to the GND terminal with a short bar.
Firmly Insert the AC input cord plug into an outlet.
The heat sink may become hot. Do not touch as it may cause burns.

6 R4G/R4GE series
2-4 Installation
2-4-1 Installation Conditions
Set the product on a level place to use.
For natural air-cooling models, air flows from the sides and bottom to the top of
the unit. Secure a space at least 10 cm or more around the unit for good
ventilation.
If the unit is installed in a rack, equipment, or enclosed cabinet, take measures
such as forced ventilation to prevent exhaust heat from returning to the air inlet.
For forced air-cooling models, air is drawn in from the front of the product and
exhausted from the rear. Secure a space at least 30 cm or more around the unit
for good ventilation.
If dust collects in the air inlet, remove it immediately.
it prevents the unit from cooling.
Do not place anything on top of the product. It prevents the unit from cooling.
Do not expose the unit to dusty, corrosive, or inflammable gas areas.
Do not install the product in a place where condensation may occur.
Do not use substitute parts or modify the internal circuits of the product.
For repair or modification, please contact us.
Prevent liquids or metals from entering the product through the air inlet and outlet.
It may result in malfunction, electric shock, or fire.
Do not store or use the product in a place where conductive dust, such as iron
powder, can enter through the air inlet/outlet. Doing so may cause a short circuit,
resulting in electric leakage, burnout, fire, or malfunction.
When doing some work near this product such as welding, disconnect all
connection wires (input/output wiring, signal wires, etc.) from the product before
working on it.
Ensure safety in case of malfunction.
In the event of a malfunction, unplug the AC input cord from the power outlet.

7 R4G/R4GE series
2-5 External View
2-5-1 Front Panel
(18)
(7)
(6)
(8)
(12)
(14)
(10)
(11)
(17)
(3)
(1)
(16)
(5)
(2)
(4)
(9)
９
(13)
(15)
FINE
REGULATED DC POWER SUPPLY
POWER
LOCK
OCP
SET
OVP/
CV
CC
V
A
OUTPUT
VOLTAGE
CURRENT
R4G18-2
－
＋
GND
REMOTE
!
|
○
(1) Voltmeter
(2) Ammeter
(3) Remote enabled indicator (REMOTE
LED)
(4) OUTPUT ON indicator (OUTPUT LED)
(5) OUTPUT ON/OFF switch
(6) + Output terminal
(7) - Output terminal
(8) GND terminal
(9) Model name
(10) Voltage mode indicator (CV LED)
(11) Current mode indicator (CC LED)
(12) Output voltage setting dial
(13) FINE switch
(14) Output current setting dial
(15) SET switch (SET LED)
(16) OVP/OCP switch (OVP/OCP LED)
(17) LOCK switch (LOCK LED)
(18) POWER ON/OFF switch

8 R4G/R4GE series
2-5-2 Rear Panel
R4GE series:
INPUTAC**V
(1)
The “**” in “INPUT AC**V” varies depending
of the type of input voltage.
(1) AC input connector
R4G series:
INPUTAC**V
(1)
The “**”in “INPUT AC**V”varies depending
on the type of input voltage.
(1) AC input connector
(2) Master/Slave input output terminals,
TB2
(3) Function setting switch, SW1
(4) One control ON/OFF switch
(5) Remote sensing ON/OFF switch
(6) Remote interface connector, TB1
(5)
(4)
(3)
(2)
(6)

9 R4G/R4GE series
2-6 External Dimensions (Unit: mm):
2-6-1 Width: 84 mm
Model: R4G/E6-2, R4G/E18-2, R4G/E36-1

10 R4G/R4GE series
2-6-2 Width: 105 mm
Model: R4G/E8-5, R4G/E18-3, R4G/E18-5, R4G/E36-3, R4G/E45-2, R4G/E60-1.2, R4G/E80-1,
R4G/E120-0.3, R4G/E120-0.6, R4G/E160-0.45, R4G/E250-0.3, R4G/E360-0.2,
R4G/E650-0.1

11 R4G/R4GE series
2-6-3 Width: 210 mm
Model: R4G/E18-10, R4G/E36-5, R4G/E45-4

12 R4G/R4GE series
2-7 Remote Interface Connector (TB1) and Function Setting Switch (SW1)
2-7-1 Remote Interface Connector (TB1)
This product is a power supply unit that generates a large current.
If a large current flowed into TB1 due to an incorrect connection, there might be a risk of
failure or burnout.
Be sure to confirm the following precautions before use.
Do not connect anything to PIN 4, 8, 9, 14, 18, 20, 22, 23, 24, and 25.
Doing so may lead to unit damage.
Do not directly connect PIN 5 and PIN 10 to the +S.
Do not directly ground PIN 5 and PIN 10 to the ground.
When grounding, connect the + output terminal to the ground.
Do not wire near sources of large noise. Doing so may result in malfunction or
breakdown.
(Note) If the above situation is unavoidable, it is recommended to use the -LGob
option (Optical GPIB/RS-232C interface board).
PIN 5 and PIN 10 are internally connected to +S. Therefore, equipment connected to
TB1 should be floating.
The wiring from the following pins should be short ( a few meters or lower).
TB1 PIN 1, 2, 3, 5, 7, 10, 15, 16, 17、21, 26
When using this unit with the "-" output terminal grounded, a voltage equal to the output
will be applied to TB1 pins. Be careful because this may be dangerous.
However, PINs 6, 11, 12, 13, 19, and 26 are insulated from other PINs.
For details, refer to [7-4-2 Status Output].
Do not connect PIN 5 or PIN 10 on the
TB1 to the "+" output.
Do not share the common for the external
voltage input of each unit when connecting
the units in series.
1
2
25
26
PIN 2: Current mode program input
PIN 4NC
PIN 6Common for external status output (CV, CC, FLT, OUTPUT, POWER ON)
PIN 8NC
PIN 10 + Common (LS, LD)
PIN 12 Current mode status output
PIN 14 NC
PIN 16 + Sense
PIN 18 NC
PIN 20 NC
PIN 22 NC
PIN 24 NC
PIN 26 POWER ON status output
Voltage mode program input PIN 1
Output current monitor output
PIN 3
+ Common PIN 5
LD door switch input
PIN 7
NC
PIN 9
FLT status output PIN11
Status output for voltage mode PIN13
Output voltage monitor output
PIN15
- Sense
PIN17
OUTPUT status output
PIN19
Remote switch input: PIN21
NC PIN23
NC PIN25
Load
10
5
TB1
Load
1
2
5
10
1
2
5
10