Mattel HotWheels RC HW UNSTOPPABLE TIGER SHARK User manual

54 6
132
AA (LR6) 1.5V
x2
2
1a
2
1b
3
b
a
1
OR
HVIN: HGV87R ( ), HGV87T ( )
Operating Frequency: 2420MHz -2462MHz
Maximum radio frequency power transmitted:
: -1.84dBm (0.65mW), : -0.85dBm (0.82mW)
The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged
before first use.
1. Slide the power switch to CHARGE ( ) .
2. Open the charge port cover.
3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000
mAH USB charger (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle
is charging.
5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is
complete. A full charge will usually take approximately 90 minutes. Charging time may vary.
6. Close the charge port cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle.
TM
4+
HGV87-0970-G2_DOM
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
• Play safely! Do not drive the vehicle in the street!
• DO NOT pick up the vehicle while in motion.
• Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
• Adult supervision is recommended when this vehicle is being operated.
• To avoid accidental operation, remove all batteries from the remote controller when not in use and switch
the vehicle OFF before storage.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not recharge battery if it is hot. Allow it to cool before recharging.
• Do not recharge a battery pack that shows leakage or corrosion.
• Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
• If the battery pack and/or charging port are wet, thoroughly dry before charging.
• Do not recharge non-rechargeable batteries.
• The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal
in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of
separately according to local regulations on battery collection and recycling.
• Do not dispose of the batteries in a fire.
Stomp!
Wheelie Spin!
Chomp!
Wheelie!
1. Drive forward and backward in full speed to build momentum.
2. As the vehicle is going backwards, quickly push
the driving control all the way up to do a wheelie!
3. Drive forward to keep the wheelie going!
3: SET UP (CONTD.)
D. STEERING ALIGNMENT
SKILL CHECK!
Remember, steering directions are flipped on the
remote controller when you are driving backward!
Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle's steering been aligned?
CHECKLIST
STUNTS
CONTROLS
1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge.
For best performance, always start with a fully-charged battery. Your vehicle's running time may change
depending on driving style and driving environment.
2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles
running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to
stay away from these!
3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it
won't work properly.
4. Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries
from remote controller before storage.
5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does
get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally
dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh
battery(ies) before operation.
6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To
resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds.
To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
5: CONSUMER INFORMATION
4: HOW TO DRIVE
1: CONTENTS
3: SET UP
2: FEATURES
BOTTOM VIEW
ALIGNMENT BUTTONS
FORWARD/BACKWARD LEFT/RIGHT STEERING
NOTE: Operating range of the remote controller is up to 30 m (98 ft).
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (+ and –).
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
SAFETY TIPS
RECHARGEABLE BATTERY SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Protect the environment by not disposing of this product or any batteries with household waste.
This symbol indicates that this product shall not be treated as household waste. Check your local
authority for recycling advice and facilities.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
®
HGV87-0970-G2_I/S_DOM
Size: 16.5” x 12”
A. REMOTE CONTROLLER BATTERY INSTALLATION
B. CHARGING THE VEHICLE
TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before
recharging the vehicle.
TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To
resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote
controller's driving control joystick forward/backward to pair the vehicle and remote controller.
Pairing
Pairing is complete
DRIVING
CONTROLS
LED INDICATOR STOMP BUTTON
STEERING
ALIGNMENT
BATTERY BOX
CHARGE
PORT
COVER
POWER SWITCH
LED INDICATOR
1. Unscrew the battery cover with a Phillips head
screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included)
with polarity (+/-) as shown inside the battery
compartment. For longer life, use alkaline batteries.
3. Replace battery cover and tighten screw.
4. Replace batteries in the remote controller if the LED on
the remote controller does not go on during play or if the
vehicle does not respond well after a recharge.
1. Check the vehicle's steering alignment before playing by
driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left,
press the alignment button in the opposite direction a few
times until it runs in a straight line.
1. Slide the power switch to ON (I) on the vehicle.
2. Press the stomp button or push the remote controller's driving control
joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on
remote controller.
NOTE: If the vehicle does not respond to the remote controller after pairing,
switch the vehicle off then back on to try pairing again or replace the
batteries in the remote controller if the batteries are drained.
©2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter
Building, 1 BrunelWay, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond,Victoria, 3121. Consumer Advisory Service - 1300 135
312. Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone]. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19,
Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia.
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
CAUTION:
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol .
HW UNSTOPPABLE
TIGER SHARK™
Vehicle is charging
Vehicle is fully charged
Red
Green
OR
I
O
= ON
= OFF
= CHARGE
CHARGE PORT
G1: Added Elec. Data;
G2: Updated the images of Wheelie Spin.

54 6
132
AA (LR6) 1.5V
x2
2
1a
2
1b
3
b
a
1
OR
HVIN: HGV87R ( ), HGV87T ( )
Operating Frequency: 2420MHz -2462MHz
Maximum radio frequency power transmitted:
: -1.84dBm (0.65mW), : -0.85dBm (0.82mW)
The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged
before first use.
1. Slide the power switch to CHARGE ( ) .
2. Open the charge port cover.
3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000
mAH USB charger (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle
is charging.
5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is
complete. A full charge will usually take approximately 90 minutes. Charging time may vary.
6. Close the charge port cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle.
TM
4+
HGV87-0970-G2_DOM
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
• Play safely! Do not drive the vehicle in the street!
• DO NOT pick up the vehicle while in motion.
• Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
• Adult supervision is recommended when this vehicle is being operated.
• To avoid accidental operation, remove all batteries from the remote controller when not in use and switch
the vehicle OFF before storage.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not recharge battery if it is hot. Allow it to cool before recharging.
• Do not recharge a battery pack that shows leakage or corrosion.
• Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
• If the battery pack and/or charging port are wet, thoroughly dry before charging.
• Do not recharge non-rechargeable batteries.
• The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal
in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of
separately according to local regulations on battery collection and recycling.
• Do not dispose of the batteries in a fire.
Stomp!
Wheelie Spin!
Chomp!
Wheelie!
1. Drive forward and backward in full speed to build momentum.
2. As the vehicle is going backwards, quickly push
the driving control all the way up to do a wheelie!
3. Drive forward to keep the wheelie going!
3: SET UP (CONTD.)
D. STEERING ALIGNMENT
SKILL CHECK!
Remember, steering directions are flipped on the
remote controller when you are driving backward!
Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle's steering been aligned?
CHECKLIST
STUNTS
CONTROLS
1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge.
For best performance, always start with a fully-charged battery. Your vehicle's running time may change
depending on driving style and driving environment.
2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles
running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to
stay away from these!
3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it
won't work properly.
4. Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries
from remote controller before storage.
5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does
get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally
dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh
battery(ies) before operation.
6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To
resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds.
To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
5: CONSUMER INFORMATION
4: HOW TO DRIVE
1: CONTENTS
3: SET UP
2: FEATURES
BOTTOM VIEW
ALIGNMENT BUTTONS
FORWARD/BACKWARD LEFT/RIGHT STEERING
NOTE: Operating range of the remote controller is up to 30 m (98 ft).
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (+ and –).
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
SAFETY TIPS
RECHARGEABLE BATTERY SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Protect the environment by not disposing of this product or any batteries with household waste.
This symbol indicates that this product shall not be treated as household waste. Check your local
authority for recycling advice and facilities.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
®
HGV87-0970-G2_I/S_DOM
Size: 16.5” x 12”
A. REMOTE CONTROLLER BATTERY INSTALLATION
B. CHARGING THE VEHICLE
TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before
recharging the vehicle.
TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To
resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote
controller's driving control joystick forward/backward to pair the vehicle and remote controller.
Pairing
Pairing is complete
DRIVING
CONTROLS
LED INDICATOR STOMP BUTTON
STEERING
ALIGNMENT
BATTERY BOX
CHARGE
PORT
COVER
POWER SWITCH
LED INDICATOR
1. Unscrew the battery cover with a Phillips head
screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included)
with polarity (+/-) as shown inside the battery
compartment. For longer life, use alkaline batteries.
3. Replace battery cover and tighten screw.
4. Replace batteries in the remote controller if the LED on
the remote controller does not go on during play or if the
vehicle does not respond well after a recharge.
1. Check the vehicle's steering alignment before playing by
driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left,
press the alignment button in the opposite direction a few
times until it runs in a straight line.
1. Slide the power switch to ON (I) on the vehicle.
2. Press the stomp button or push the remote controller's driving control
joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on
remote controller.
NOTE: If the vehicle does not respond to the remote controller after pairing,
switch the vehicle off then back on to try pairing again or replace the
batteries in the remote controller if the batteries are drained.
©2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter
Building, 1 BrunelWay, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond,Victoria, 3121. Consumer Advisory Service - 1300 135
312. Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone]. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19,
Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia.
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
CAUTION:
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol .
HW UNSTOPPABLE
TIGER SHARK™
Vehicle is charging
Vehicle is fully charged
Red
Green
OR
I
O
= ON
= OFF
= CHARGE
CHARGE PORT
G1: Added Elec. Data;
G2: Updated the images of Wheelie Spin.

54 6
132
AA (LR6) 1.5V
x2
2
1a
2
1b
3
b
a
1
OR
HVIN: HGV87R ( ), HGV87T ( )
Operating Frequency: 2420MHz -2462MHz
Maximum radio frequency power transmitted:
: -1.84dBm (0.65mW), : -0.85dBm (0.82mW)
The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged
before first use.
1. Slide the power switch to CHARGE ( ) .
2. Open the charge port cover.
3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000
mAH USB charger (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle
is charging.
5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is
complete. A full charge will usually take approximately 90 minutes. Charging time may vary.
6. Close the charge port cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle.
TM
4+
HGV87-0970-G2_DOM
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
• Play safely! Do not drive the vehicle in the street!
• DO NOT pick up the vehicle while in motion.
• Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
• Adult supervision is recommended when this vehicle is being operated.
• To avoid accidental operation, remove all batteries from the remote controller when not in use and switch
the vehicle OFF before storage.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not recharge battery if it is hot. Allow it to cool before recharging.
• Do not recharge a battery pack that shows leakage or corrosion.
• Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
• If the battery pack and/or charging port are wet, thoroughly dry before charging.
• Do not recharge non-rechargeable batteries.
• The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal
in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of
separately according to local regulations on battery collection and recycling.
• Do not dispose of the batteries in a fire.
Stomp!
Wheelie Spin!
Chomp!
Wheelie!
1. Drive forward and backward in full speed to build momentum.
2. As the vehicle is going backwards, quickly push
the driving control all the way up to do a wheelie!
3. Drive forward to keep the wheelie going!
3: SET UP (CONTD.)
D. STEERING ALIGNMENT
SKILL CHECK!
Remember, steering directions are flipped on the
remote controller when you are driving backward!
Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle's steering been aligned?
CHECKLIST
STUNTS
CONTROLS
1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge.
For best performance, always start with a fully-charged battery. Your vehicle's running time may change
depending on driving style and driving environment.
2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles
running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to
stay away from these!
3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it
won't work properly.
4. Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries
from remote controller before storage.
5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does
get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally
dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh
battery(ies) before operation.
6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To
resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds.
To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
5: CONSUMER INFORMATION
4: HOW TO DRIVE
1: CONTENTS
3: SET UP
2: FEATURES
BOTTOM VIEW
ALIGNMENT BUTTONS
FORWARD/BACKWARD LEFT/RIGHT STEERING
NOTE: Operating range of the remote controller is up to 30 m (98 ft).
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (+ and –).
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
SAFETY TIPS
RECHARGEABLE BATTERY SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Protect the environment by not disposing of this product or any batteries with household waste.
This symbol indicates that this product shall not be treated as household waste. Check your local
authority for recycling advice and facilities.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
®
HGV87-0970-G2_I/S_DOM
Size: 16.5” x 12”
A. REMOTE CONTROLLER BATTERY INSTALLATION
B. CHARGING THE VEHICLE
TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before
recharging the vehicle.
TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To
resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote
controller's driving control joystick forward/backward to pair the vehicle and remote controller.
Pairing
Pairing is complete
DRIVING
CONTROLS
LED INDICATOR STOMP BUTTON
STEERING
ALIGNMENT
BATTERY BOX
CHARGE
PORT
COVER
POWER SWITCH
LED INDICATOR
1. Unscrew the battery cover with a Phillips head
screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included)
with polarity (+/-) as shown inside the battery
compartment. For longer life, use alkaline batteries.
3. Replace battery cover and tighten screw.
4. Replace batteries in the remote controller if the LED on
the remote controller does not go on during play or if the
vehicle does not respond well after a recharge.
1. Check the vehicle's steering alignment before playing by
driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left,
press the alignment button in the opposite direction a few
times until it runs in a straight line.
1. Slide the power switch to ON (I) on the vehicle.
2. Press the stomp button or push the remote controller's driving control
joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on
remote controller.
NOTE: If the vehicle does not respond to the remote controller after pairing,
switch the vehicle off then back on to try pairing again or replace the
batteries in the remote controller if the batteries are drained.
©2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter
Building, 1 BrunelWay, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond,Victoria, 3121. Consumer Advisory Service - 1300 135
312. Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone]. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19,
Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia.
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
CAUTION:
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol .
HW UNSTOPPABLE
TIGER SHARK™
Vehicle is charging
Vehicle is fully charged
Red
Green
OR
I
O
= ON
= OFF
= CHARGE
CHARGE PORT
G1: Added Elec. Data;
G2: Updated the images of Wheelie Spin.

54 6
132
AA (LR6) 1.5V
x2
2
1a
2
1b
3
b
a
1
OR
HVIN: HGV87R ( ), HGV87T ( )
Operating Frequency: 2420MHz -2462MHz
Maximum radio frequency power transmitted:
: -1.84dBm (0.65mW), : -0.85dBm (0.82mW)
The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged
before first use.
1. Slide the power switch to CHARGE ( ) .
2. Open the charge port cover.
3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000
mAH USB charger (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle
is charging.
5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is
complete. A full charge will usually take approximately 90 minutes. Charging time may vary.
6. Close the charge port cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle.
TM
4+
HGV87-0970-G2_DOM
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
• Play safely! Do not drive the vehicle in the street!
• DO NOT pick up the vehicle while in motion.
• Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
• Adult supervision is recommended when this vehicle is being operated.
• To avoid accidental operation, remove all batteries from the remote controller when not in use and switch
the vehicle OFF before storage.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not recharge battery if it is hot. Allow it to cool before recharging.
• Do not recharge a battery pack that shows leakage or corrosion.
• Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
• If the battery pack and/or charging port are wet, thoroughly dry before charging.
• Do not recharge non-rechargeable batteries.
• The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal
in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of
separately according to local regulations on battery collection and recycling.
• Do not dispose of the batteries in a fire.
Stomp!
Wheelie Spin!
Chomp!
Wheelie!
1. Drive forward and backward in full speed to build momentum.
2. As the vehicle is going backwards, quickly push
the driving control all the way up to do a wheelie!
3. Drive forward to keep the wheelie going!
3: SET UP (CONTD.)
D. STEERING ALIGNMENT
SKILL CHECK!
Remember, steering directions are flipped on the
remote controller when you are driving backward!
Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle's steering been aligned?
CHECKLIST
STUNTS
CONTROLS
1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge.
For best performance, always start with a fully-charged battery. Your vehicle's running time may change
depending on driving style and driving environment.
2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles
running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to
stay away from these!
3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it
won't work properly.
4. Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries
from remote controller before storage.
5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does
get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally
dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh
battery(ies) before operation.
6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To
resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds.
To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
5: CONSUMER INFORMATION
4: HOW TO DRIVE
1: CONTENTS
3: SET UP
2: FEATURES
BOTTOM VIEW
ALIGNMENT BUTTONS
FORWARD/BACKWARD LEFT/RIGHT STEERING
NOTE: Operating range of the remote controller is up to 30 m (98 ft).
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (+ and –).
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
SAFETY TIPS
RECHARGEABLE BATTERY SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Protect the environment by not disposing of this product or any batteries with household waste.
This symbol indicates that this product shall not be treated as household waste. Check your local
authority for recycling advice and facilities.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
®
HGV87-0970-G2_I/S_DOM
Size: 16.5” x 12”
A. REMOTE CONTROLLER BATTERY INSTALLATION
B. CHARGING THE VEHICLE
TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before
recharging the vehicle.
TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To
resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote
controller's driving control joystick forward/backward to pair the vehicle and remote controller.
Pairing
Pairing is complete
DRIVING
CONTROLS
LED INDICATOR STOMP BUTTON
STEERING
ALIGNMENT
BATTERY BOX
CHARGE
PORT
COVER
POWER SWITCH
LED INDICATOR
1. Unscrew the battery cover with a Phillips head
screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included)
with polarity (+/-) as shown inside the battery
compartment. For longer life, use alkaline batteries.
3. Replace battery cover and tighten screw.
4. Replace batteries in the remote controller if the LED on
the remote controller does not go on during play or if the
vehicle does not respond well after a recharge.
1. Check the vehicle's steering alignment before playing by
driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left,
press the alignment button in the opposite direction a few
times until it runs in a straight line.
1. Slide the power switch to ON (I) on the vehicle.
2. Press the stomp button or push the remote controller's driving control
joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on
remote controller.
NOTE: If the vehicle does not respond to the remote controller after pairing,
switch the vehicle off then back on to try pairing again or replace the
batteries in the remote controller if the batteries are drained.
©2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter
Building, 1 BrunelWay, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond,Victoria, 3121. Consumer Advisory Service - 1300 135
312. Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone]. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19,
Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia.
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
CAUTION:
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol .
HW UNSTOPPABLE
TIGER SHARK™
Vehicle is charging
Vehicle is fully charged
Red
Green
OR
I
O
= ON
= OFF
= CHARGE
CHARGE PORT
G1: Added Elec. Data;
G2: Updated the images of Wheelie Spin.

54 6
132
AA (LR6) 1.5V
x2
2
1a
2
1b
3
b
a
1
OR
HVIN: HGV87R ( ), HGV87T ( )
Operating Frequency: 2420MHz -2462MHz
Maximum radio frequency power transmitted:
: -1.84dBm (0.65mW), : -0.85dBm (0.82mW)
The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged
before first use.
1. Slide the power switch to CHARGE ( ) .
2. Open the charge port cover.
3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000
mAH USB charger (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle
is charging.
5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is
complete. A full charge will usually take approximately 90 minutes. Charging time may vary.
6. Close the charge port cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle.
TM
4+
HGV87-0970-G2_DOM
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
• Play safely! Do not drive the vehicle in the street!
• DO NOT pick up the vehicle while in motion.
• Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
• Adult supervision is recommended when this vehicle is being operated.
• To avoid accidental operation, remove all batteries from the remote controller when not in use and switch
the vehicle OFF before storage.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not recharge battery if it is hot. Allow it to cool before recharging.
• Do not recharge a battery pack that shows leakage or corrosion.
• Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
• If the battery pack and/or charging port are wet, thoroughly dry before charging.
• Do not recharge non-rechargeable batteries.
• The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal
in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of
separately according to local regulations on battery collection and recycling.
• Do not dispose of the batteries in a fire.
Stomp!
Wheelie Spin!
Chomp!
Wheelie!
1. Drive forward and backward in full speed to build momentum.
2. As the vehicle is going backwards, quickly push
the driving control all the way up to do a wheelie!
3. Drive forward to keep the wheelie going!
3: SET UP (CONTD.)
D. STEERING ALIGNMENT
SKILL CHECK!
Remember, steering directions are flipped on the
remote controller when you are driving backward!
Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle's steering been aligned?
CHECKLIST
STUNTS
CONTROLS
1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge.
For best performance, always start with a fully-charged battery. Your vehicle's running time may change
depending on driving style and driving environment.
2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles
running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to
stay away from these!
3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it
won't work properly.
4. Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries
from remote controller before storage.
5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does
get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally
dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh
battery(ies) before operation.
6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To
resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds.
To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
5: CONSUMER INFORMATION
4: HOW TO DRIVE
1: CONTENTS
3: SET UP
2: FEATURES
BOTTOM VIEW
ALIGNMENT BUTTONS
FORWARD/BACKWARD LEFT/RIGHT STEERING
NOTE: Operating range of the remote controller is up to 30 m (98 ft).
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (+ and –).
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
SAFETY TIPS
RECHARGEABLE BATTERY SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Protect the environment by not disposing of this product or any batteries with household waste.
This symbol indicates that this product shall not be treated as household waste. Check your local
authority for recycling advice and facilities.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
®
HGV87-0970-G2_I/S_DOM
Size: 16.5” x 12”
A. REMOTE CONTROLLER BATTERY INSTALLATION
B. CHARGING THE VEHICLE
TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before
recharging the vehicle.
TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To
resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote
controller's driving control joystick forward/backward to pair the vehicle and remote controller.
Pairing
Pairing is complete
DRIVING
CONTROLS
LED INDICATOR STOMP BUTTON
STEERING
ALIGNMENT
BATTERY BOX
CHARGE
PORT
COVER
POWER SWITCH
LED INDICATOR
1. Unscrew the battery cover with a Phillips head
screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included)
with polarity (+/-) as shown inside the battery
compartment. For longer life, use alkaline batteries.
3. Replace battery cover and tighten screw.
4. Replace batteries in the remote controller if the LED on
the remote controller does not go on during play or if the
vehicle does not respond well after a recharge.
1. Check the vehicle's steering alignment before playing by
driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left,
press the alignment button in the opposite direction a few
times until it runs in a straight line.
1. Slide the power switch to ON (I) on the vehicle.
2. Press the stomp button or push the remote controller's driving control
joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on
remote controller.
NOTE: If the vehicle does not respond to the remote controller after pairing,
switch the vehicle off then back on to try pairing again or replace the
batteries in the remote controller if the batteries are drained.
©2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter
Building, 1 BrunelWay, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond,Victoria, 3121. Consumer Advisory Service - 1300 135
312. Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone]. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19,
Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia.
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
CAUTION:
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol .
HW UNSTOPPABLE
TIGER SHARK™
Vehicle is charging
Vehicle is fully charged
Red
Green
OR
I
O
= ON
= OFF
= CHARGE
CHARGE PORT
G1: Added Elec. Data;
G2: Updated the images of Wheelie Spin.

54 6
132
AA (LR6) 1.5V
x2
2
1a
2
1b
3
b
a
1
OR
HVIN: HGV87R ( ), HGV87T ( )
Operating Frequency: 2420MHz -2462MHz
Maximum radio frequency power transmitted:
: -1.84dBm (0.65mW), : -0.85dBm (0.82mW)
The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged
before first use.
1. Slide the power switch to CHARGE ( ) .
2. Open the charge port cover.
3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000
mAH USB charger (not included).
4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle
is charging.
5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is
complete. A full charge will usually take approximately 90 minutes. Charging time may vary.
6. Close the charge port cover.
7. Recharge the vehicle if the vehicle begins to run slowly or does not respond.
NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle.
TM
4+
HGV87-0970-G2_DOM
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
• Play safely! Do not drive the vehicle in the street!
• DO NOT pick up the vehicle while in motion.
• Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
• Adult supervision is recommended when this vehicle is being operated.
• To avoid accidental operation, remove all batteries from the remote controller when not in use and switch
the vehicle OFF before storage.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not recharge battery if it is hot. Allow it to cool before recharging.
• Do not recharge a battery pack that shows leakage or corrosion.
• Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
• If the battery pack and/or charging port are wet, thoroughly dry before charging.
• Do not recharge non-rechargeable batteries.
• The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal
in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of
separately according to local regulations on battery collection and recycling.
• Do not dispose of the batteries in a fire.
Stomp!
Wheelie Spin!
Chomp!
Wheelie!
1. Drive forward and backward in full speed to build momentum.
2. As the vehicle is going backwards, quickly push
the driving control all the way up to do a wheelie!
3. Drive forward to keep the wheelie going!
3: SET UP (CONTD.)
D. STEERING ALIGNMENT
SKILL CHECK!
Remember, steering directions are flipped on the
remote controller when you are driving backward!
Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle's steering been aligned?
CHECKLIST
STUNTS
CONTROLS
1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge.
For best performance, always start with a fully-charged battery. Your vehicle's running time may change
depending on driving style and driving environment.
2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles
running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to
stay away from these!
3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it
won't work properly.
4. Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries
from remote controller before storage.
5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does
get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally
dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh
battery(ies) before operation.
6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To
resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds.
To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
5: CONSUMER INFORMATION
4: HOW TO DRIVE
1: CONTENTS
3: SET UP
2: FEATURES
BOTTOM VIEW
ALIGNMENT BUTTONS
FORWARD/BACKWARD LEFT/RIGHT STEERING
NOTE: Operating range of the remote controller is up to 30 m (98 ft).
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (+ and –).
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
SAFETY TIPS
RECHARGEABLE BATTERY SAFETY INFORMATION
BATTERY SAFETY INFORMATION
Protect the environment by not disposing of this product or any batteries with household waste.
This symbol indicates that this product shall not be treated as household waste. Check your local
authority for recycling advice and facilities.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
®
HGV87-0970-G2_I/S_DOM
Size: 16.5” x 12”
A. REMOTE CONTROLLER BATTERY INSTALLATION
B. CHARGING THE VEHICLE
TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before
recharging the vehicle.
TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To
resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote
controller's driving control joystick forward/backward to pair the vehicle and remote controller.
Pairing
Pairing is complete
DRIVING
CONTROLS
LED INDICATOR STOMP BUTTON
STEERING
ALIGNMENT
BATTERY BOX
CHARGE
PORT
COVER
POWER SWITCH
LED INDICATOR
1. Unscrew the battery cover with a Phillips head
screwdriver (not included).
2. Install 2 AA (LR6) 1.5V alkaline batteries (not included)
with polarity (+/-) as shown inside the battery
compartment. For longer life, use alkaline batteries.
3. Replace battery cover and tighten screw.
4. Replace batteries in the remote controller if the LED on
the remote controller does not go on during play or if the
vehicle does not respond well after a recharge.
1. Check the vehicle's steering alignment before playing by
driving it forward to see if it is driving straight.
2. If the vehicle automatically steers toward the right/left,
press the alignment button in the opposite direction a few
times until it runs in a straight line.
1. Slide the power switch to ON (I) on the vehicle.
2. Press the stomp button or push the remote controller's driving control
joystick forward/backward after switching on the vehicle.
3. Pairing is complete when the LED changes from flashing red to solid red on
remote controller.
NOTE: If the vehicle does not respond to the remote controller after pairing,
switch the vehicle off then back on to try pairing again or replace the
batteries in the remote controller if the batteries are drained.
©2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter
Building, 1 BrunelWay, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond,Victoria, 3121. Consumer Advisory Service - 1300 135
312. Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: [phone]. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19,
Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia.
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
CAUTION:
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol .
HW UNSTOPPABLE
TIGER SHARK™
Vehicle is charging
Vehicle is fully charged
Red
Green
OR
I
O
= ON
= OFF
= CHARGE
CHARGE PORT
G1: Added Elec. Data;
G2: Updated the images of Wheelie Spin.