Maxview COMBO/50 Assembly Instructions

Installation & User Instructions
COMBO/50
UK contact:
Helpline: [phone]
Email: suppor[email protected]o.uk
Web: www.maxview.co.uk
Maxview reserve the right to change specifications without prior notice
9111457 Iss 1
Roam Combo
We have partnered up with one of the largest
suppliers of Wi-Fi products worldwide.
Roam Combo Combo Powered by
This manual provides information on how to control the Roam Combo Router using your
devices internet browser. Most of these functions can be completed easier and faster
using the Maxview Roam Combo App. See the Roam Combo App instruction manual for
more
Maxview Address:
Maxview Ltd, Garage Lane, Setchey, King’s Lynn, Norfolk. PE33 0AT. UK

Contents
Record your Purchase
Please fill in the details below once purchased. This information will be required in the unlikely event of a fault
occurring with this system.
SERIAL NUMBER
2. Record your Purchase
3. Product Contents
3. Tools Required
3. Choosing a Service Provider
4. Accessories
Installation Instructions
5. Antenna Installation
8. Signal Booster Installation
12. Inserting Sim Card
13. Router Installation
Router - Getting Connected and Basic Functions
16. Get to know your Router
17. Getting Online
19. Factory Reset
Router - Advanced Functions and Changing Router
Settings
21. Connecting to the Web User Interface
23. Logging out of the Web User Interface
Router - Changing the Primary Internet Source
from 3G/4G to Wi-Fi
25. Changing the Primary Source
28. Changing the Routers LAN IP Address
Router - Other Functions
30. Managing and Removing Wi-Fi Connections
30. Changing Wi-Fi SSID (name) and Password
32. Entering SIM PIN
33. Controlling Data Usage & Other Functions
34. Router Firmware Update
Additional Information
35. General Safety Warnings
35. Terms and Conditions
36. Maintenance
36. Troubleshooting & FAQ’s - For Internet with Router
40. Troubleshooting & FAQ’s - For TV with Signal Booster
41. 2 year Guarantee
42. Environment
43. Specifications
44. Certification
Introduction
Thank you for purchasing this product, should you have any difficulty using your
Roam Combo please contact our friendly Customer Helpline on [phone] or
email [e-mail].
SSID
PASSWORD
See page 16 to see where you can find this information.
2

Product Contents
A. Antenna Mounting Foot
B. Combo Antenna* with 2 x 0.8m cables with
SMA connectors and 1 x 5m coaxial cable
C. Roof Clamp
D. ‘F’ Connector
E. Fused Power Cable (For Signal Booster)
F. Fixing Screws
G. 1m F to Coaxial Flylead
*White or Grey Plastics
A
I
H
CL
G
Tools required
- Power Drill
- 2.5mm Drill Bit
- Pozidrive (No.2) Screwdriver
- Cross Head Screwdriver
Choosing a Service Provider
To use the Maxview Roam Combo, you will need a suitable data SIM card (sold separately).
The Maxview Roam Combo is unlocked, so you can use any service provider. The best package
will depend on many factors such as data usage, budget, location of travel and usage habits,
however pre-paid data plans are usually more cost effective.
- File/Emery Paper
- Surface Cleaner
- Knife
!
3
E
- 25mm Hole Saw
- 4mm Allen Key
- Side Cutters
- Hack Saw
B
J
H. Signal Booster
I. 1.5m Ethernet Cable
J. 12V Vehicle Power Supply (for Router)
K. Router Bracket
L. 4G/5G Router
M. SIM Adaptor Pack
N. Internal Wi-Fi Antenna
O. Fixing Template
D
F
K
M
N
O

4
Roam Combo Extension Cables
Extension cables can be purchased separately to
allow a flexible mounting position to the router.
1 metre MXL050/EXT1
2 metres MXL050/EXT2
Accessories -
Sold separately
Roam Combo 230V PSU
230V ac to 12V dc Power Supply Unit
to power a Roam Combo. For indoor use only.
MXL050/PSUUK3 metres MXL050/EXT3

Antenna
Installation Instructions
5

6
Mounting Foot
with wet seal and
Clamping Tool
Towards front of vehicle

7
!Allow the Flexible Adhesive to cure as per the manufacturers guidelines before travel.
Front of
vehicle
X = 2mm
Y = 25mm
XY
X
X
X
Choose a location, ensure the antenna is positioned
on a flat surface and is clear from obstructions.
Use the included template and drill 5 x 2mm holes.
Use hole position (Y) as a pilot hole to drill a larger
25mm hole. Clean up hole, ensuring the location of
the Mounting Foot is clean and clear from debris
and dirt.
Position the Mounting Foot and press down firmly.
3
Apply sealant generously to the wet seal channel,
ensuring the bead is consistent in size with no gaps.
2
OPTIONAL - For optimum secure mounting, use the
4 supplied Roof Fixing Screws, to secure the
Mounting Foot to the vehicle roof.
4
If your roof thickness is between 19-40mm, you
can screw the Foot Clamp into the Mounting Foot
underside to cover the hole inside the vehicle.
Note: The Clamping Tool can
be cut down to suit your
vehicle roof thickness.
Turn anti-clockwise until
tight and secure Foot Clamp
with the Foot Clamp Screw.
Installation of the Mounting Foot is now complete.
5
1
19-40mm
Place the Antenna Head Unit onto the Mounting Foot.
Tighten the 4 Foot Mounting Bolts by hand with an
Allen Key.
We recommend the use of a Torque Wrench set to
3.5Nm.
Installing the Antenna Head Unit
6

Signal Booster (For TV)
Installation Instructions
8

9
Cable routing
Route Coaxial Cable (A) inside vehicle to Variable
Signal Booster which should be located near your
TV/Receiver.
Note cable can be shortened to suit application.
A
Please Note:
When fitting the Signal Booster and Router, there should be as much distance between the
two units as possible. The TV Coax cable and Router SMA cables should also not be routed
next to each other wherever possible. This will reduce the potential for interference between
the two systems.
!
✗✓

Connections & features
A. 12/24V power input
B. On/off power switch
C. Wall fixing hole
Operation
1. Slide power switch to the right. The LED indicator should now be on.
2. Turn the gain control knob clockwise to increase signal strength.
Power source methods
- 12/24V DC (Fused Power Cable included for 12/24V wiring)
- 12/24V DC PSU Output (230V PSU)
F
C
D. Antenna input
E. TV output 1
F. TV output 2
G. Gain control knob
H. Power indicator
Can be mounted to vehicle
shelving or side panels using the
2 screws provided.
Note:
Before drilling always check for
hidden electrical wires or
plumbing.
Mounting Option
Using Signal Booster
I
OUT OUT
IN
12/24V
ADE
BGH
CC
F
10
Fitting F Connector
If you decide to shorten the cable please see below method of preparing cable.
Cut cable to required length. Strip
away 12mm of outer insulation.
Gather strands of screening braid,
twist together and wind back
around outer insulation. Cut foil
to be flush with outer insulation.
12
Strip away 10mm of inner
insulation around the inner wire.
Check none of the screening braid
is touching the inner copper wire.
3
Cut off inner copper wire to
extend 3mm beyond plug body.