Maxview CRANK UP B2590/50SNZ Manual

Installation & operating instructions
B2590/50SNZ Crank Up
New Zealand contact:
Phone: [phone]
Email: [email protected]
Web: www.rvsupplies.co.nz
Maxview reserve the right to change specifications without prior notice
9111418NZ Iss 1

Contents:
Introduction 2
Guarantee 2
Proper use & operation 3
Safety precautions 3
Application example 4
Product contents 4
Required tools and equipment 4
Selecting an installation location 4
Specifications 5
Attaching Antenna Mount Plate 6
and LNB Park Plate
Introduction:
Please read these instructions fully before using the antenna for the first time. The operation of the antenna has
been designed to be as simple as possible however should you require any technical assistance please contact
[phone] or visit www.rvsupplies.co.nz
Page 2
Attaching Antenna Unit to 7
Mount Plate
Installing cables 8
Installing Handle 9
Finding a satellite 12
Start a search 12
Lowering antenna 14
Skew adjustment 15
Reception map 15
Elevation Map 16
3 year guarantee:
Every new Crank Up system is thoroughly inspected and tested before leaving the factory and is covered by our
three years guarantee from the date of original purchase.
Maxview is responsible for the cost of a replacement part if the original part is determined to be defective
under the terms of guarantee. The customer is responsible for the cost of replacement parts after three years.
This guarantee does not cover installation or external wiring.
Should any trouble develop during the guarantee period or experience a problem with the product
contact [phone] OR Email: [e-mail]
Please make sure you have the following ready when you call:
• Model number • Serial number • Date of purchase • Clear and concise details of the fault
• Details of who installed the product
The guarantee does not apply where:
• The product has been abused, misused, improperly installed or improperly maintained.
• Repairs have been made or attempted by a third party other then Maxview
• Repairs are required due to normal wear and tear
• Modications have been made to the product
• The antenna unit has been opened
• Damaged caused by abrasive cleaning or power washing
• Circumstances beyond the control of Maxview that have caused the product to no longer operate correctly
• Customer is not the original owner or cannot provide proof of purchase
In no event shall Maxview be liable for any indirect, incidental, or consequential damages from the sale or use
of the product. This disclaimer applies both during and after the term of the warranty. This does not affect your
statutory rights.

Safety precautions:
Read this manual carefully and become familiar with your satellite antenna. Understand its applications, its
limitations and any hazards involved. Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury. Maxview declines all responsibility in the event of incident or accident if they are due
to a non observation of the installation instructions or the way the product is used.
No modifications are permissible to the Antenna Unit or Handle Assembly
Installation
• Installation should be carried out by a competent person
• Take care when working at heights keeping work area clean and tidy to avoid trip hazards
• Use creeper boards where necessary to ensure roof construction can support your weight
• Use a recommended adhesive from page 4 to bond the antenna unit to vehicle roof and follow the
manufacturer’s instructions during application
• Do not travel until adhesive has cured noting that curing times vary with weather conditions
• Power tools should be used in accordance with manufacturer’s instructions
• All electrical work should be carried out by a competent person. If in doubt seek advice from a qualied
electrician
Operation
• Before starting your journey check that antenna is in the park position
• The maximum speed of vehicle with antenna mounted on roof is 81mph (130km/h)
• Never operate the antenna if someone is in close proximity of the antenna
• If high winds or electrical storms are anticipated lower antenna to park position
• Do not allow children to operate the antenna unit
• Do not operate the Crank Up with snow or ice on the antenna
Servicing
• If in the event that you do experience a problem with the system call
[phone] or visit www.rvsupplies.co.nz
• Any inspection or repair must be carried out by Maxview or an appointed representative of the manufacturer
• No regular maintenance required on the system
• Do not remove cover on Antenna
• Do not use solvent or abrasive cleaning agents on the system
• Use a suitable mild detergent to clean the Antenna Unit
• Do not pressure wash the Antenna Unit
• Check the Antenna Unit xings for mechanical integrity at least once a year
Page 3
Proper use & operation:
The Crank Up is designed to be installed in a motorhome, caravan or horsebox to automatically locate a
television broadcast satellite when the vehicle is stationary.
The Antenna which is to be permanently mounted externally to the roof structure of a motorhome/caravan
horsebox. The construction of the roof structure should be suitably robust and have no protruding obstacles
Use of the equipment for any other purpose than the one specified is not permitted and will invalidate the
guarantee.

Page 4
Application example:
Product contents:
> Antenna Unit
> Handle Assembly
> 50cm Antenna (separate carton)
> Accessory Pack
> LNB Park Plate x 1
> No.10 Screws for plastic (small) x 10
> M4 Screws for Plastic x 5
> Cable Clips x 12
> Aluminium 20mm Tube x 1
> Steel 4mm Spindle x 1
> Self Adhesive Zone Map x 1
> Compass x 1
> M5 Washers x 2
Selecting an installation location:
Positioning the Antenna Unit and the Handle Assembly
Decide where you wish to mount your satellite system, taking into account
obstacles both on the roof and inside the vehicle. The system MUST be pointing towards the rear of the vehicle
> Check for obstructions such as roof lights and vents
> Check for electrical cables beneath screw fixing points
> Check the ‘F’ cables will reach satellite receiver (Maxview can supply extended cables)
> Do not allow the dish to overhang the edge of the vehicle
> Clearance around antenna system when in use is shown with reference I
> Ensure adequate clearance of the handle assembly from cupboard doors and light fittings
> Hexagonal socket key 4mm
> Deburrer/Round File/Emery paper
> Conduit (recommend method for securing cables)
*Maxview recommends the following adhesives:
> Sikaflex®-512 Caravan
> Geocel® Geobond HM
> Sikaflex®-252
> Sikaflex®-55AT
Required tools and equipment (not supplied):
> 32mm hole saw
> 2.5mm and 8mm twist drill
> Power Drill
> Hacksaw
> No.2 Phillips screwdriver
> Weather Resistant Elastic Adhesive* and Applicator gun
> Surface Cleaner
> 10mm spanner

Page 5
A: 17
B: 80
C: 50
D: 62
E: 79
F: ø43*
G: 45
H: 25
E
A
D
B C
H
G
F
I
H: 25
I: 110
J: 16
K: 5 J
K
Product Dimensions
Operating:
Low stream line prole, only 17cm in park position
Power
Powering: Manual operation no power
required
System
Elevation Range: 10º to 70º
Azimuth Range: 380º
Skew Angle: ±45º
Cable Type: CAI approved 100 coaxial
cable
UV Protection: All external plastic parts are
UV stabilised
Testing: Fully weatherproof and
watertight construction
System has passed extensive
water ingress test
System Weight: 10kg
Specifications:
LNB
Type: High Quality Single LNB
Output: Single
Typical Gain: 34.5dB
Frequency: 10.75GHz
Arm Cable: RG179
Antenna
Material: Aluminium
Reflector Thickness: 1mm
Finish: Powder coated with U.V.
inhibited polyester-based
Dimensions: 65cm dish: 53 x 49.5 cm
Mounting
Plate Material: Aluminium
Fixing Method: Recommended adhesive
(Sikaex, Geocel or
equivalent)
Fixing Studs: 6 x M5 studs for system
removal
Cable Entry: Coaxial cable joining cover
under antenna system

Attaching Antenna Mount Plate & LNB Park Plate:
1. Remove antenna unit from wooden transit packaging
2. Remove mounting plate from Antenna Unit by removing 6 x M6 nuts using 10mm spanner
3. Clean roof, Mounting Plate and LNB Park Plate in accordance with adhesive manufacturer’s guidelines
4. Mark a centre line for the antenna making sure dish will not overhang vehicle
5. Align notches on plate with centre line
6. Mark the position of 6 screw fixing holes and centre hole
7. Mark position of LNB Park Plate
Page 6
10. Apply rings of adhesive* (see page 4) to
surface of Antenna Mounting Plate and LNB
Park Plate and firmly place them into position.
Important Note:
Adhesive MUST be used to give a water tight
seal between mounting plate and installation
surface.
8. Drill 6 x 2.5mm pilot holes into the roof
9. Using a 32mm holesaw drill the centre hole
through the roof
150mmDirection of travel
Central Line
Antenna Mount Plate
LNB Park
Plate

Page 7
11. Place a small amount of adhesive into each pilot hole before screwing plate to roof.
12. Wipe off excess adhesive with a cloth.
Note:
> Follow manufacturer’s instructions when applying adhesive. Do not travel until adhesive has cured noting
that curing times vary with weather conditions.
> Take care when working at heights. Always follow ladder manufacturer’s safety advice.
> Use creeper boards where necessary to ensure roof construction can support your weight.
> Power tools should be used in accordance with manufacturer’s instructions.
Attach Antenna Unit to Mounting Plate
Carefully lower the antenna unit onto the Mounting Plate and re-attach the M6 Nuts and Washers that were
previously removed.
6 x No. 10 screws (large)
Note:
DO NOT remove transit tape
Caution: Replace Nylon locking nuts if they have been removed more than twice. The locking action of the
Nylon becomes less effective if repeatedly assembled and disassembled.

Page 8
Installing Cable Entry Cover:
1. Plan your installation
2. Drill hole in roof
3. Prepare surface for adhesion
4. Apply sealant as shown in A,B,C
(we recommend Sikaflex-512 Caravan)*
5. Position top hat
6. Position cable entry cover
7. Wipe excess sealant with a dry cloth
Applying sealant example:
!!
!= Generously apply
wet seal adhesive
!
Top hat
Hole location
tabs
Cable
32mm ø
A
B
C
Direction of travel
(front of vehicle)
Installing cables:
1. Check there are no hidden cables in the roof structure and that the hole location is clear of obstructions both
internally and externally.
2. See below for Cable Entry Cover instructions
Application example:
Please note this model has
only a single coaxial output
Direction of travel
(front of vehicle)

Page 9
1. Push the aluminium tube into the plastic coupler and insert into the antenna unit through the hole in the
ceiling With the plastic coupler pushed up tight to the ceiling, mark the aluminium tube along all four sides.
Installing the handle:
Drilled hole
Aluminium tube
Coupler
2. Cut the 20mm square tube with a hacksaw.
Make the cut so that the line is left on the
discarded part of the tube.
3. Now mark and cut the 4mm spindle so that it is
40mm longer than the tube.
40mm

Page 10
4. With the Coupler Bush aligned to the rear of the vehicle insert the Tube and Coupler Bush through the ceiling
hole and into the antenna unit.


Rear of vehicle
5. Place the Base Plate over the Coupler Bush. Point
the arrow to the rear of the vehicle. Mark the
four xing holes. Drill four 2.5mm pilot holes or
use a bradawl. With four No.10 screws fix the
Base Plate to the ceiling.
6. Take the Dish Direction Unit and turn the azimuth
lock lever to the red position to release the brake.
Locate the Dish Direction onto the Coupler Bush
and use three M4 screws fix it in place.
Rear of vehicle Align arrows
Azimuth lock lever
Red = Unlocked
Green = Locked
(safe to travel)
Aluminium Tube should not protrude past
the coupler bush