Maxview MXL028/65 Connect Owner's manual

Installation, Satellite Information & Fault Finding
MXL028/65 & 85 Connect (Single, Twin & Quad)
UK contact:
Helpline: [phone]
Email: suppor[email protected]o.uk
Web: www.maxview.co.uk
Maxview reserve the right to change specifications without prior notice
9111420 Iss 1
Booklet 1 of 2

Contents
Installation
Application Example 4
Connections & Features 5
Product Contents 5
Required Tools & Equipment 5
Selecting an installation location 6
Positioning Control Box 6
Attaching Antenna Mount Cover 7
and LNB Park Plate
Electrical installation 8
Attaching Antenna Unit to Mount Plate 9
Installing Cables 9
Installing Cable Entry Plate 10
Installing Control Box 10
Connection Diagram 11
Attaching Satellite Dish to Unit 11
Testing Bluetooth Connectivity & Installing 12
Updates
Introduction
Please read these instructions fully before using the antenna for the first time. The operation of the antenna has
been designed to be as simple as possible however should you require any technical assistance please contact
Maxview customer service on [phone] or visit www.maxview.co.uk.
Proper Use & Operation
The Connect is designed to be installed in a motorhome, caravan or horsebox to automatically locate a television
broadcast satellite when the vehicle is stationary. The system comprises of 2 main components.
1. The Antenna which is to be permanently mounted externally to the roof structure of a motorhome/caravan/
horsebox. The construction of the roof structure should be suitably robust and have no protruding obstacles
2. The Control Box is designed to be mounted internally in a cupboard. This controls the antenna unit through a
cable connection and is powered by 12v DC only.
Use of the equipment for any other purpose than the one specified is not permitted and will invalidate the
warranty.
All instructions and models are subject to change. In accordance with policy of progressive product, the company
reserve the right to alter specifications.
Copyright© these instructions are the sole property of Maxview Ltd and may not be reproduced.
Please keep these instructions safe for future reference.
Recycle packaging where facilities exist.
Satellite Information
Finding a Satellite 13
Skew Adjustment 14
Fault Finding
On Screen Error Modes 15
Control Box Error Modes 16
General Faults & FAQs 18
Portable Connectivity Troubleshooting 19
Ignition 20
Connecting to a Satellite Receiver 20
Power Consumption 20
3 Year Guarantee 21
Environment 22
Specifications 24
Page 2
PLEASE READ BEFORE INSTALLATION

Safety Precautions
Read this manual carefully and become familiar with your satellite antenna. Understand its applications, its
limitations and any hazards involved. Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury. Maxview declines all responsibility in the event of incident or accident if they are due
to a non observation of the installation instructions or the way the product is used.
No modifications are permissible to the Antenna Unit & Control Box.
Installation
• Installation should be carried out by a competent person
• Take care when working at heights keeping work area clean and tidy to avoid hazards
• Use creeper boards where necessary to ensure roof construction can support your weight
• Use a recommended adhesive from page 5 to bond the antenna unit to vehicle roof and follow the
manufacturer’s instructions during application
• Do not travel until adhesive has cured noting that curing times vary with weather conditions
• Power tools should be used in accordance with manufacturer’s instructions
• All electrical work should be carried out by a competent person. If in doubt seek advice from a
qualified electrician
• The Control Box is for internal use only and is not waterproof
Operation
• Before starting your journey check that antenna is in the park position
• The maximum speed of vehicle with antenna mounted on roof is 81mph (130km/h)
• Never operate the antenna if someone is in close proximity of the antenna
• Disconnect power to the antenna before installation or adjusting LNB skew angle
• If high winds or electrical storms are anticipated lower antenna to park position
• Maintain adequate ventilation around the Control Box to avoid overheating
• Do not allow children to operate the antenna unit
• Remove Control Box fuse before accessing the roof space around the antenna unit
• Do not operate the Connect with snow or ice on the antenna
Servicing
• If in the event that you do experience a problem with the system call Maxview Customer Service
[phone] with your model & serial number to hand
• Any inspection or repair must be carried out by Maxview or an appointed representative of the manufacturer
• No regular maintenance required on the system
• Do not remove cover on Antenna or Control Box
• Do not use solvent or abrasive cleaning agents on the system
• Use a soft damp cloth to clean the Control Box
• Use a suitable mild detergent to clean the Antenna Unit
• Do not pressure wash the Antenna Unit
• Check the Antenna Unit fixings for mechanical integrity at least once a year
Page 3


A. Antenna
The Antenna is mounted to the roof. It uses electric motors to scan for satellite signals.
The single variant has 2 cable connections; 1 for controlling the motors and 1 satellite signal
cable from the single LNB.
The twin variant has 3 cable connections; 1 for controlling the motors and 2 satellite signal
cables from the twin LNB.
The quad variant has 5 cable connections; 1 for controlling the motors and 4 satellite signal
cables from the single LNB.
B. Control Box
The Control Box requires wired connections for power, antenna control and satellite signal.
It can be mounted discretely in a cupboard and can be fixed vertically and horizontally.
This can then be controlled directly from the Control Box or using the Connect App
Application Example
A
B
INSTALLATION
Page 4

Connections & Features
Control Box:
1. Fuse
2. Power Switch
Product contents
> Antenna Unit / Control Box
> 65/85cm Antenna (separate carton)
> Accessory Pack
> LNB Park Plate x 1
> Control Box bracket x 2
> No.10 Screws x 6
> No.6 Screws x 4
> Cable Clips x 6 (x 12 for quad)
> M6 Button Head Screw x 4
> M6 Locking Nut x 4
> 6mm Plastic Washer x 4
> Cable Entry Plate x 1
Required tools and equipment (not supplied)
> 32mm hole saw
> 2.5mm twist drill
> Power Drill
> No.2 Phillips screwdriver
> Weather Resistant Elastic Adhesive* and Applicator gun
> Surface Cleaner
> 10mm spanner
> Hexagonal socket key 4mm
> Deburrer/Round File/Emery paper
> Conduit (recommended method for securing cables)
> Automotive 2.5mm² cable
> Electrical connector block
> Flylead (for connection to satellite receiver)
*Maxview recommends the following adhesives:
> Sikaflex®-512 Caravan
> Geocel® Geobond HM
> Sikaflex®-252
Reference page 16 for interface information
5. Status LED
6. Receiver Out
7. LNB Coaxial In
8. Antenna Connectors
9. Installation Button
10. Power Input
1 2 3 4 5
6 7 8 9 10
3. Power LED
4. Pair Button
Page 5