May Wes QD2 Instruction Manual

2.1
2.7
1
2.6
2.11
2.10
2.12
2.4
2.5
2.8
2.9
2.3
2.2
JOHN DEERE 90/40 SERIES
ALL ROWS EXCEPT ROW 6 ON 8 ROW HEAD
QD2 STALK STOMPER PARTS LISTING/ASSEMBLY INSTRUCTIONS
NOTES:
1
43016 - 14" Stalk Stomper Shoe Assy
2
41748 - 14" Stalk Stomper Shoe W/Poly
3
Install Self-Tapping Grease Fitting into end of Pivot Bolt
Torque grease fitting to 65-70 inch pounds. DO NOT OVERTIGHTEN!
PAGE 1 OF 2
1
2
3
ITEM # PART # DESCRIPTION QTY
1 43010 QD2 HEADER BRACKET 1
2 43003 STALK STOMPER ASSY 9" 1
2.1 43004 SHOE BRACKET ASSY 1
2.2 41825 STALK STOMPER SHOE W/POLY 9" 1
2.3 01040 SPRING 1
2.4 00691 PIN, 1/4" X 3" COTTER 1
2.5 00931 CHAIN 1
ITEM # PART # DESCRIPTION QTY
2.6 01001 BOLT, CUSTOM (GREASEABLE) 1
2.7 00213 NUT, 7/16"-14 HEX TOP LOCK 1
2.8 00249 WASHER, 3/8" FLAT 2
2.9 00104 BOLT, 3/8"-16 X 1" HEX 2
2.10 00209 NUT, 3/8"-16 HEX 2
2.11 01009 GREASE FITTING, 1/4"-28 STRAIGHT 1
2.12 01046 CHAIN SLEEVE 1
120 Eastgate Drive SE
PO Box 7
Hutchinson, MN 55350
1-800-788-6483
1-320-587-2322
1-320-587-6112 (Fax)
WWW.MAYWES.COM
Doc #: 10197_A

Roller Frame
(Corn Head Frame)
Header Bracket
Stalk Stomper Assy
Gear Box Bolts
Factory Hardware
Pin
Assembly
Mount
Pin
JOHN DEERE 90/40 SERIES
ALL ROWS EXCEPT ROW 6 ON 8 ROW HEAD
STALK STOMPER INSTALLATION
Safety Procedure:
- Park Combine on level ground and engage the parking brake.
- Raise the head and lock in the upright position.
- Support all row units that stalk stompers will be installed on to ensure row units remain stationary during
installation.
Installation Procedure:
- Remove the gear box bolts and the eye bolts which secure the row unit to the main frame of the corn head.
Replace the eyebolts with Header Bracket (43010) by inserting the threaded rods thru the roller frame
mount. Insert the gear box bolts thru the header bracket into the gearbox and tighten to factory
recommended torque specifications. Secure the threaded rods reusing the factory hardware and tighten
to factory recommended torque specifications (Fig. 1).
- Lift the Stalk Stomper Assy (43003) into mating features in the Header Bracket (43010).
Pull Stalk Stomper Assembly back until lock pin assembly snaps into place.
Figure 1
Completed Installation
PAGE 2 OF 2
120 Eastgate Drive SE
PO Box 7
Hutchinson, MN 55350
1-800-788-6483
1-320-587-2322
1-320-587-6112 (Fax)
WWW.MAYWES.COM
Doc #: 10197_A