Mayline DUAL COLUMN XR BASE User manual

NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.
When ordering components, specific size information may be required.
Contact a Mayline Customer Service Representative. 1 800 822 8037
ASSEMBLY INSTRUCTIONS
for DUAL COLUMN XR BASE
REF. # QTY. DESCRIPTION PART No.
E1 16 M6 x 16mm SCREW X419
E2 16 STAR WASHER W29
E3 3 #10 x 3/4 SCREW X11
E4 8 #10 x 1" SCREW X12
E5 2 #6 x 5/8 SCREW X10
E6 3 CABLE CLAMP F191
E7 2 #8 x 1 3/4" SCREW X533
COMPONENTS:
REF. # QTY. DESCRIPTION PART No.
1 2 LIFT ACTUATOR Z460
2 2 XR FOOT A7310 (26") A7792 (23")
3 1 CHANNEL CROSS CALL~~
4 2 TOP PLATE B6969
5 1 CONTROL BOX, 2 LEG Z537
6 1 MEMORY SWITCH Z463
7 1 MAIN CABLE Z467
8 2 39.37 MOTOR CABLE Z464
~~ enotes Size
OPTIONAL HARDWARE BAG (PART No. A8241)
REF. # QTY. DESCRIPTION PART No.
9 1 Anti Collision Dongle Z498*
I549 REV. 09 6-2016
(1)
HARDWARE BAG (PART No. A7311) *For individual item, order by part number

1. Place each Lift Actuator Column Assembly (1) upside
down with the cord toward the floor. CAUTION: Do not
pinch Cord Assembly
2. Position the XR Foot (2) over Lift Actuator Column
Assembly (1) with the longer portion of the Foot toward
the front. The column front is determined by the
position of the cross channel clip welded on the column.
Position this clip to the rear.
3. Attach the XR Foot (2) to the Lift Actuator Column
Assembly (1) with four M6 x 16 mm Screws (E1) and
Star Washers (E2).
4. Place the assembled columns upright and attach the
Cross Channel (3). Position the Cross Channel flange
with end notches toward the floor. Slide the Cross
Channel bracket onto the tapered channel clip on each
Column. Gently tap the Cross Channel in place with a
Rubber Mallet to assure a tight fit.
5. In the event that you must reposition the Actuator
Cord. Gently remove the cord and strain relief from the
notch in the top of the Lift Actuator Column Assembly
(1). Position the cords so that they are toward the
center of the assembled base. Insert the strain relief
into the appropriate Column notch. Attach Top Plate
(4) to each Actuator Column with four M6 x 16 mm
Screws (E1) and Star Washers (E2).
6. Attach the Memory Switch (6), Main Cord (7), and the
39.37 Cables (8) to the Control Box (5).
7. Attach Anti Collision Dongle Option (when ordered).
To install the Anti Collision Dongle (9), simply plug the
dongle into one of the two control ports on the Control
Box (5). The function is only active when the dongle is
mounted if you remove the dongle you disable the
function.
Note: Situations where anti collision does not work.
1) If the collision happens during the initialization stage.
2) If the collision happens within the first 1000 msec or
after the control button has been released.
3) If the collision time span is too long, i.e. if the collision
is with a soft object.
Cross Channel
notches DOWN
Cords toward
center
Cord Assembly
Cross Channel clip
on REAR of Column
(2)

NOTE:
a) #10 x 3/4" Screws (E3) are provided for Clamp installation only.
b) #10 x 1" Screws (E4) are provided for Work Surface attachment only.
c) #8 x 1 3/4" Screws (E7) are provided for Control Box installation only.
ATTENTION:
MAYLINE includes screws for the installation of a Work
Surface with a minimal thickness of 1 inch (25.4mm).
Switch cable OVER
Cross Channel
(3)
7. PRIOR TO ATTACHING A WORKSURFACE.
Place the Memory Switch cable over the top of the
Cross Channel.
8. Align the holes in the Top with the holes in the Top
Plates (4) and secure in place with eight #10 x 1"
Screws (E4).
9. Choose a desired location for the Control Box (5)
and attach with two #8 x 1 3/4" Screws (E7). Connect
the motor cables to the columns.
10. Place the Memory Switch (6) in a comfortable and
accessible location on the underside of the Top and
attach it with two #6 x 5/8 Screws (E5).
11. Route the actuator column cables and the switch
cable away from moving components and secure them
in place with Cable Clamps (E6) and Screws (E3).

INSTRUCTIONS for
DESK SWITCH w/ PROGRAMMABLE
MEMORY
1. Initialize system by pressing down and holding for 5 to 10
seconds after table bottoms out.
2. Push 'UP' to desired height.
3. To save this position in Memory:
A.) Press (Set)
B.) Press (do not hold) button , , or
Position is now saved under the number chosen.
4. To change to different height, press or .
This position may be saved by repeating Step 3 and using
one of the other buttons or using the same button to change
the previous setting. Up to 3 positions may be stored.
5. To go to new height position, press or , or press stored
height under , , or . Unit will automatically stop at
the stored position.
S
1
321
2 3
21 3 S
(4)