Maytronics Dolphin Skagerrak20 User manual

EN

Robotic Pool Cleaner Skagerrak 20 User Instructions
1
Robotic Pool Cleaner
Skagerrak 20
User Instructions
Contents
EN

2
Robotic Pool Cleaner Skagerrak 20 User Instructions
Robotic Pool Cleaner
Skagerrak 20
User Instructions
1. INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner.
WearesurethatyourMaytronicsRoboticPoolCleanerwillprovideyouwithreliable,convenient
andcost-effectivepoolcleaning.Itsreliablefiltrationinallpoolconditionsandactivebrushing,
enhance poolhygiene.
RoboticPoolCleanersbyMaytronicsdeliveradvancedcleaningtechnologys,long-lasting
performance andeasymaintenance.Youandyourfamilywillbefreetoenjoyyourswimwith
full confidence that your pool is completely clean.
2. SPECIFICATIONS
Motor protection: IP 68
Minimumdepth:0.80m/2.6ft
Maximumdepth:5m/16.4ft
Digital Power supply
Input: 100-125AC Volts/ 200-230 AC Volts
50-60 Hertz
Output: <30 VDC
IP 54
3. WARNINGS AND CAUTIONS
3.1 Warnings
• Use the originally supplied power supply only
• Ensuretheelectricaloutletisprotectedbyagroundfaultinterrupter(GFI)oran
earth leakage interrupter(ELI)
• Keep the power supply out of standing water
• Position the power supply at least 3m/10ft away from the edge of the pool
• Do not enter the pool while the Pool Cleaner is working
• Unplug the power supply before servicing
3.2 Cautions
Use the Pool Cleaner in the following water conditions only:
Chlorine
Maximum 4 ppm
pH
7.0-7.8
Temperature
6-34°C / 43-93°F
NaCl
Maximum 5000 ppm

Robotic Pool Cleaner Skagerrak 20 User Instructions
3
4. POOL CLEANER PARTS
Robotic Pool Cleaner Model Skagerrak 20
Power supply unit - options
Filtration options
Caddy kit - optional

4
Robotic Pool Cleaner Skagerrak 20 User Instructions
5. USING THE POOL CLEANER
5.1 Setup
Before using the Pool Cleaner for the first time, perform the following steps:
5.1.1
Position the power supply
5.1.2
Unwind the cable and stretch it out completely so that it has
so that it is approximately in the
middle of the long side of the
pool at a distance of 3m /10ft.
no kinks.
5.1.3
Attach the floating cable to the power
5.1.4
Plug in the power supply and leave it in the
supply by inserting it with the notch on the
connector (1), lined up with the groove in
the socket on the power supply, and turning
clockwise (2).
OFF position.
1
2
3m/10ft

Robotic Pool Cleaner Skagerrak 20 User Instructions
5
5.2 Putting the Pool Cleaner into the pool
5.2.1
PutthePoolCleanerintothepool.
5.2.2
Turn the power supply ON.
ReleasethePoolCleanerandletitsinktothefloor
of the pool.
Makesurethatthefloatingcableisfreeofany
obstructions.
The Pool Cleaner will now operate until it has
reached the end of the cleaning cycle.
5.3 Indicator Lights - Model Classic 11+ only
Light
Indication
Blue blinking
Normal operation of the Pool Cleaner
Green blinking
Remote-Control or Smartphone communicate with the Pool Cleaner
5.3.1 Indicator lights.
ON

6
Robotic Pool Cleaner Skagerrak 20 User Instructions
5.4 Removing the Pool Cleaner from the pool
Turn OFF and unplug the power supply.
5.4.1
5.4.2
Using the floating cable, bring the Pool Cleaner to the pool’s edge.
Using the handle, remove the Pool Cleaner from the pool.
DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.
5.4.3
Place the Pool Cleaner on the edge of the pool and let the water drain out.

Robotic Pool Cleaner Skagerrak 20 User Instructions
7
6. CLEANING THE DUAL FILTERBASKET
Make sure the power supply is switched off and unplugged.
It is highly recommended to clean the filter basket after each cleaning cycle.
Note: Do not let the filter panels dry out before cleaning.
6.1 Cleaning after use - removing and cleaning the dual filter basket
6.1.1
Openthefiltercover.
6.1.2
Upon opening the filter cover,
the handle will lift independently.
6.1.3
Liftupthebasket.
6.1.4
Open thelatch
6.1.5
Clean the filter basket
torelease the bottom lid
in order to remove the
debris.
with a hose.

8
Robotic Pool Cleaner Skagerrak 20 User Instructions
6.2 Periodic filter cleaning –recommended at least once a month
Dismantle the 4 ultra-fine filter panels of the outer basket, according to the following steps:
6.2.1
Holding downthe
6.2.2
Dismantle the panels,
6.2.3
Continue to dismantle
handle,removetheinner
net basket. starting by pressing on panel1usingyourthumbs. the panels in the order of their
numbers: 2
—
> 3
—
> 4.
6.2.4
Cleanthefilterpanelswithahose.
6.2.5
Assemble the filter panels according to the
following order: Panel 4
—
> 3
—
> 2
—
> 1.
6.2.6
Insert the clean filter basket and close the filter cover.