Maytronics MCC6 User manual

8151890
User Instructions
Robotic Pool Cleaner MCC6/MTC6
MCC6
MTC6

Contents
1. INTRODUCTION ....................................................................... 2
2. SPECIFICATIONS ...................................................................... 2
3. WARNINGS AND CAUTIONS ................................................... 2
3.1. Warnings............................................................................ 2
3.2. Cautions............................................................................. 2
4. POOL CLEANER PARTS ............................................................ 3
5. USING THE POOL CLEANER.................................................... 4
5.1. Setup.................................................................................. 4
5.2. Putting the Pool Cleaner into the pool.............................. 6
5.3. Removing the Pool Cleaner from the pool........................ 7
6. CLEANING THE FILTER BAG OR CARTRIDGES ....................... 8
6.1. Removing and cleaning the filter bag ................................ 8
6.2. Replacing the filter bag ..................................................... 9
6.3. Cleaning the filter cartridges ............................................. 9
6.4. Cleaning the impeller ........................................................ 10
7. OFFSEASON STORAGE............................................................ 11
8. TROUBLESHOOTING................................................................ 12
Robotic Pool Cleaner MCC6/MTC6
User Instructions

2Robotic Pool Cleaner MCC6/MTC6 |User Instructions
Robotic Pool Cleaner MCC6/MTC6
User Instructions
1. INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner.
We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and
cost effective pool cleaning. Its reliable filtration in all pool conditions, active brushing, and all-surface
climbing brush enhance maximum pool hygiene.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologies, long lasting
performance and easy maintenance. You and your family will be free to enjoy your swim with full
confidence that your pool is completely clean.
2. SPECIFICATIONS
Motor protection: IP 68
Minimum depth: 0.4 m (1.33 ft)
Maximum depth: 5 m (16.4 ft)
3. WARNINGS AND CAUTIONS
3.1. Warnings
• Use the originally supplied power supply only
• Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth
leakage interrupter (ELI)
• Keep the power supply out of standing water
• Position the power supply at least 3.5 m (12 ft) away from the edge of the pool
• Do not enter the pool while the Pool Cleaner is working
• Unplug the power supply before servicing
• Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
3.2. Cautions
When not in use store the Pool Cleaner on the Caddy in a shaded area.
Use the Pool Cleaner in the following water conditions only:
Chlorine Max 4 ppm
pH 7.0 - 7.8
Temperature 6 °C – 35 °C (43 °F – 95 °F)
NaCl Maximum = 5000 ppm
CAUTION

Robotic Pool Cleaner MCC6/MTC6 |User Instructions 3
4. POOL CLEANER PARTS
Robotic Pool Cleaner Model MCC6
Frame Cartridges and 4 ultra-fine filters Spring clean-up filters Bottom lid and filter Bag
optional
Combined Brush
For rough ceramic
surface and mosiac tiles.
PVC Brush
For concrete, PVC,
fiberglass and liner.
Wonder Brush
For smooth ceramics.
Optional Brushes
Wonder Brush
For smooth ceramics.
Combined Brush
For rough ceramic
surface and mosiac tiles.
PVC Brush
For concrete, PVC,
fiberglass and liner.
Optional Brushes
Brushes
Filtration
Power supply unit
Robotic Pool Cleaner Model MTC6

4Robotic Pool Cleaner MCC6/MTC6 |User Instructions
5. USING THE POOL CLEANER
The Pool Cleaner is very simple to use. Simply put it into the pool and make sure that it is properly
sitting on the floor of the pool. Turn it ON and let it get the job done.
5.1. Setup
Before using the Pool Cleaner for the first time perform the following steps:
Unwind the cable and stretch it out
completely so that it has no kinks.
Some models arrive with plastic coverings on the brushes.
Remove them before use.
While pushing in the handle buttons turn the ring so that the large projection on the ring lines up with
the projection on the Pool Cleaner body.

Robotic Pool Cleaner MCC6/MTC6 |User Instructions 5
While pushing the button on each
float pull it all the way out.
Position the power supply so that it is
approximately in the middle of the long side
of the pool at a distance of 3.5 m (12 ft).
Attach the floating cable to the power supply
by inserting it with the notch on the connector (1)
lined up with the groove in the socket on the
power supply and turning clockwise (2).
Plug in the power supply and leave it in the OFF position.
Click Click
3.5 m (12 ft)
1
2

6Robotic Pool Cleaner MCC6/MTC6 |User Instructions
5.2. Putting the Pool Cleaner into the pool
Holding the Pool Cleaner upside down in
the water gently rock it back and forth with
your fingers holding the plastic doors on
the bottom lid open to release trapped
air. Continue until no more bubbles are
released.
If your Pool Cleaner is equipped with brushes that
contain sponges, dip the brushes in the water and
squeeze them so that they will absorb water the first time
you use the Pool Cleaner, or if the brushes have dried out
between uses.
Release the Pool Cleaner and let it sink to the floor of the
pool.
Make sure that the floating cable is free of any
obstructions.
To avoid kinks in the floating cable, place approximately
enough cable in the water for the Pool Cleaner to reach
the farthest corner of the pool.
Turn the power supply ON.
The Pool Cleaner will now operate until it has
reached the end of the cleaning cycle.
ON

Robotic Pool Cleaner MCC6/MTC6 |User Instructions 7
5.3. Removing the Pool Cleaner from the pool
CAUTION
Turn OFF and unplug the power supply
Using the floating cable, bring the Pool Cleaner to the pool’s edge.
Using the handle remove the Pool Cleaner from the pool.
CAUTION
DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.
Place the Pool Cleaner on the edge of the pool and let the
water drain out.
OFF

8Robotic Pool Cleaner MCC6/MTC6 |User Instructions
6. CLEANING THE FILTER BAG OR CARTRIDGES
Depending on the model, your Pool Cleaner may be equipped with a filter bag or cartridges.
It is recommended to clean the filter bag or cartridges after each cleaning cycle.
6.1. Removing and cleaning the filter bag
CAUTION
Unplug the power supply
Turn the Pool Cleaner upside-down.
Open the bottom lid.
Remove the filter bag.
Clean the filter bag with a hose.
We recommend that you periodically wash the filter bag in a
washing machine using the gentle cycle program.
Periodically clean the brushes with a hose.
Click

Robotic Pool Cleaner MCC6/MTC6 |User Instructions 9
6.2. Replacing the filter bag
Put the filter bag over the frame so that the strap is
in the middle of the shortest side.
Make sure that filter bag is positioned
properly on the frame.
6.3. Cleaning the filter cartridges
Note: Don’t let the filter cartridges dry out before cleaning.
CAUTION
Unplug the power supply.
With the pool cleaner upside down
open the bottom lid and pull it out.
Open the clips and remove the filters.
Click