Maytronics Dolphin Supreme M5 User manual

USER INSTRUCTIONS
DOLPHIN SUPREME M5
1333 Rymal Road E. ●Hamilton, Ontario ●L8W 3N1
Phone: [phone] ●Fax: [phone]
Email: [email protected] ●Website: www.thepoolshoppe.ca

1
User Instructions

User Instructions
2

User Instructions
3

User Instructions
4

User Instructions
5

User Instructions
6

7
User Instructions

Digital switch-mode power supply with Weekly Timer
and Full Filter Bag Indicator
Your robotic pool cleaner’s power supply has a unique timer control. This allows you the
possibility to set an automatic cleaning schedule for the week ahead.
User Instructions
7
User Instructions
8
Turning the Dolphin ON to start it working
1. Plug the floating cable from the Dolphin into the power supply unit
2. Plug the electrical cable from the power supply unit into the mains
3. Press the ON/OFF switch on the power supply unit.
The Dolphin will now start to work
Input- 100-250 AC Volts
50-60 Hertz
180 Watt
Output- 30 VDC
IP 54
Assemble the power supply onto the Caddy

9
User Instructions
When the power supply is on, the 3 LEDs will blink for 5 seconds. At this time by pressing the
SELECT button you may choose a pool cleaning schedule for the coming week.
Note!- The robot will always begin to work upon set-up.
LED 1- The robot will automatically work every day for a full cycle= 7 times a week.
LED 2- The robot will automatically work every other day for a full cycle= 3 times a week.
LED 3- The robot will automatically work every 3 days= 2 times a week.
If you do not press any of the buttons in the first 5 seconds after the power supply has been
switched on the robot will work for one cycle only.
While the robot is working in weekly timer mode, the LED will blink constantly between
cycles. At the end of the week, the power supply automatically switches off.
You must schedule the robot.
Full Filter Bag Indicator
The power supply is equipped with a unique filter bag status indicator.
The red LED indicates 2 filter conditions:
When blinking- The filter is partially blocked
When lighted- The filter is blocked and must be emptied and cleaned.
If the LED does not shut-off after the filter has been emptied and cleaned, press the
RESET button while the robot is working.

Maytronics Remote Control Unit
The Remote Control Unit (RCU) offers two operation modes- Automatic mode and
Manual direction control mode. In Automatic mode, all cleaning parameters can
be changed. In Manual direction mode, the Pool Cleaner direction can be
controlled manually.
The Control Panel of the Remote Control Unit
User Instructions
10

Maytronics Remote Control Unit
Setting the Automatic Mode
Cleaning cycle
indicator
This determines the
cleaning cycle time. The
RCU allows you to
choose between the
following options.
Fast
1.5 hour cycle
Efficient
(Default Setting)
2.5 hour cycle for
everyday use
Extra
3.5 hour cycle
Delay Time
indicator
This determines when
the pool cleaner starts
to work. A delay allows
the dirt to settle to the
bottom of the pool.
Immediate start
(Default Setting)
1 hour delay
2 hour delay
Cleaning action
indicator
Allowing you to choose
from the following
options.
Standard
Floor and wall
cleaning (Default
Setting)
Ultra-Clean
Stronger suction and
slower movement.
Floor Only
Cleans only the
floor and
coves.
Walls Only
Cleans walls
and waterline
only
11
User Instructions
To Change the Automatic Mode settings
First press the Manual/Automatic select button, then set according to the following table:
Note:
After 2 minutes, if no button is pressed, the Remote Control Unit will shut-down and the Pool
cleaner will continue to work in the previous settings.
When the “Ultra-Clean,” and “Walls Only” options finish their cycles, the RCU will return to default
settings.

12
User Instructions