MDB Family 5928 Installation and operating instructions

6 Drawer Dresser (5928) - Assembly and Operation Manual
Congratulations on purchasing an MDB Family product. This product will provide many years of service
if you adhere to the following guidelines for assembly, maintenance and operation. This product is for
residential use only. Any institutional use is strictly prohibited.
Please be sure to follow the instructions for proper assembly. Use a Phillips head screwdriver for
assembling the product in addition to the Allen wrench included in the hardware box. Do not use power
screwdrivers. All of our products are made from natural woods. Please understand that natural woods
have color variations which are the result of nature and not defects in workmanship.
DO NOT SUBSTITUTE PARTS. ALL MODELS HAVE THE SAME QUANTITY OF PARTS AND HARD-
WARE. YOUR MODEL MAY LOOK DIFFERENT FROM THE ONE ILLUSTRATED DUE TO STYLIS-
TIC VARIATIONS.
revised 23DEC2014 page 1

USING ANY POWER TOOLS TO ASSEMBLE THIS FURNITURE MAY POTENTIALLY STRIP THE WOOD. DO NOT USE.
WARNING:
page 2
.
PARTS

STEP 1.
F-1/F-2
F-2
Attach left panel glides (H9) to left end panel (F-1) and right
panel glides (H7) to right end panel (F-2) using small wood
screws (H5).
Screw in 4 cam bolts (H1) to each end panel (F-1 & F-2).
page 3
STEP 2.
F-1
.

page 4
STEP 3.
STEP 4.
F-1
F-2

page 5
STEP 5.
STEP 6.
6a
6b
A

page 6
* Slide the drawers into the
dresser and check that they
glide smoothly.
STEP 7.
6c 6d
6e
6f

page 7
Serious or fatal crushing can occur when furniture tips over on children. To help prevent tip-over, follow the
steps below to install this anti-tipping strap.
FURNITURE ANTI-TIPPING KIT INSTALLATION
WARNING
Place heaviest item in the lowest drawers.
do not set TVs or other heavy objects on
top of this product.
Never allow children to climb or hang on
drawers, doors, or shelves.
Never open more than one drawer at a time.
(OR)
Do not defeat or remove the drawer interlock
system.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is permanent label. Do not attempt to remove!
Unless specifically designed to accommodate,
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
X 2
X 1 X 1
X 1
Stubby
Screwdriver
Phillips
screwdriver
(not included)
Tools Needed
Pencil
Locate a 2” x 4” stud behind the
wall, and make a mark.
8a
8b
Install the strap on the wall with long screw and washer.
2” x 4” wall stud
STEP 8.

page 8
IMPORTANT: As with all infant and baby furniture, it is important to check fasteners, screws,
and bolts periodically for tightness. Parents should ensure a safe environment for their
children by checking the furniture regularly before placing a child in the product.
Care and Cleaning:
Do not scratch or chip the finish.
Do not use abrasive chemicals for
cleaning. Clean with mild soap on a
soft rag. rinse and dry thoroughly. If
you ever refinish this furniture, be sure
to use only a non-toxic finish specified
for children’s products. If you choose
to refinish this furniture, the warranty
will be voided.
Storage:
Pine woods exchange moisture with the air adjusting
to major changes in room temperature and humidity.
Therefore it is best to place your furniture away from
heating or air-conditioning vents.
Sunlight is not friendly to solid wood furniture and
prolonged direct exposure to harsh sunlight can discolor
the finish. Be careful not to place your furniture in direct
sunlight for extended periods of time.
As with all your fine furniture, blot up spills immediately.
8c
Install the other end of strap on
the back of dresser with short
screw and washer into the wood
framing of the dresser.
Finish
KEEP THIS MANUAL IN A SAFE
PLACE FOR FUTURE REFERENCE.
READ ALL INSTRUCTIONS BEFORE USING THE PRODUCT.
KEEP THE INSTRUCTIONS FOR FUTURE USE.
This item has a manufacturer’s limited one year warranty.
Visit our web site at www.themdbfamily.com for more information.