Meanwell DRH-120-24 User manual

InstallationManual

Type：GeneralTypeDINrailwithThreePhaseorHighInputRange
（Series：DRH‐120,DRT‐240,DRT‐480,DRT‐960）
DRH‐120‐24INPUT:400‐500VAC0.65A50/60HzOUTPUT:24V5A
DRH‐120‐48INPUT:400‐500VAC0.65A50/60HzOUTPUT:48V2.5A
DRT‐240‐24 INPUT:400‐500VAC0.95A50/60HzOUTPUT:24V10A
DRT‐240‐48 INPUT:400‐500VAC0.95A50/60HzOUTPUT:48V5A
DRT‐480‐24 INPUT:400‐500VAC1.7A50/60HzOUTPUT:24V20A
DRT‐480‐48 INPUT:400‐500VAC1.7A50/60HzOUTPUT:48V10A
DRT‐960‐24 INPUT:400‐500VAC2.4A50/60HzOUTPUT:24V40A
DRT‐960‐48 INPUT:400‐500VAC2.4A50/60HzOUTPUT:24V20A

Introduction
GeneraltypewiththreephaseorhighinputrangeisaDINrailpowersupplyserieswithahighinputrange,
340‐550Vac.LikeotherMeanWell’sDINseries,theycanbemountedonaTS35StandardDINrail.

Installation
（1）Alwaysallowgoodventilationclearances,5mmleftandright,40mmaboveand20mmbelow,aroundtheunit
inusetopreventitfromoverheating.Alsoa10‐15cmclearancemustbekeptwhentheadjacentdeviceisa
heatsource.
（2）Theappropriatemountingorientationfortheunitisvertical,theinputterminalsatthebottomandoutputon
thetopforDRH‐120,theinputterminalsontherightandoutputontheleftforDRT‐240,DRT‐480and
DRT‐960.Mountingorientationsotherthanthat,suchasupsidedown,horizontal,ortable‐topmounting,is
notallowed.








（3）Usecopperwireonly,andrecommendedwiresareshownasbelow.
AWG1816 14 12 10
RatedCurrentof
Equipment(Amp)6A6‐10A13‐16A16‐25A25‐32A
Cross‐sectionof
Lead(mm2)0.751.001.52.54
Note:Currenteachwirecarriesshouldbede‐ratedto80%ofthecurrentsuggested
abovewhenusing5ormorewiresconnectedtotheunit.
Makesurethatallstrandsofeachstrandedwireentertheterminalconnectionandthescrewterminalsare
securelyfixedtopreventpoorcontact.Ifthepowersupplypossessesmulti‐outputterminals,pleasemake
sureeachcontactisconnectedtowirestopreventtoomuchcurrentstressonasinglecontact.
（4）Usewiresthatcanwithstandtemperaturesofatleast80°CsuchasUL1007.
（5）Recommendedwirestrappinglengthis5mm(0.197”).
（6）Recommendedscrewdriveris4mm,slottedtype.
（7）Therecommendedtorquesettingforterminalsis10kgf‐cm(9Lb‐in).

InstallationManual
3
12
4

（8）SuggestedfuseandmaximumnumberofthePSUsthatcanbeconnectedtoacircuitbreakerat230Vare
shownasbelow.
ModelFuseCircuitbreaker
C16D16
DRH‐120T4A/H250V1416
DRT‐240F3A/L250V810
DRT‐480F6.3A/L250V35
DRT‐960F6.3A/L250V24
Whenanexternalcircuitbreakerisutilised,aminimumvalueisrequiredtoavoidundesiredtrippingofthe
circuitbreaker.
（9）ForDRH‐120series,itiscapableofbeingconnectedbetweenany2phasesona3‐phase‐4‐wireWye(Star)
connectedsystem.









UsingafuseoracircuitbreaktoprotecttheAC/L2inputissuggested.TheAC/L2inputisinternally
non‐protected.
（10）ForDRT‐240,DRT‐480,andDRT‐960series,theyarecapableofdualphaseoperation(connectingL1,L3,FG
forDRT‐960),butthatrequiresde‐ratingoutputcurrentby20%.
（11）MountingInstruction：
Mountasshowninfigureonly,withinputterminalsdown,orelsesufficientcoolingwillnotbepossible.
AdmissibleDINrail：TS35/7.5orTS35/15
Forrailfastening：

（a）Tilttheunitslightlyrearwards.
（b）Fittheunitovertophatrail.
（c）Slideitdownwarduntilithitsthestop.
（d）Pressagainstthebottomforlocking.
（e）Shaketheunitslightlytocheckthelockingaction.










（12）ElectricalTubingandsleeve–RecognizedComponent–Tubing(YDPU2)and/orsleeving(UZFT2),rated300V,
105 minimum.℃
（13）Forotherinformationabouttheproducts,pleaserefertowww.meanwell.comfordetails.

"Click"

InstallationManual

Warning/Caution!!
（1）Riskofelectricalshockandenergyhazard.Allfailureshouldbeexaminedbyaqualifiedtechnician.Pleasedo
notremovethecaseofthepowersupplybyyourself!
（2）Riskofelectricarcsandelectricshock(dangertolife).Connectingboththeprimaryandthesecondarysides
togetherisnotallowed.
（3）Riskofburnhazard.Donottouchtheunitinoperationandshortlyafterdisconnection!
（4）Riskoffireandshortcircuit.Theopeningsshouldbeprotectedfromforeignobjectsordrippingliquids.
（5）Onlyinstalltheunitinapollutiondegree2environment(Note.1).
（6）Pleasedonotinstalltheunitinplaceswithhighmoistureornearthewater.
（7）Themaximumoperatingtemperatureis40°CforDRT‐240andDRT‐480series,50°CforDRH‐120seriesand
DRT‐960series,pleasedonotinstalltheunitinplaceswithhighambienttemperatureornearfiresource.
（8）TheFG()mustbeconnectedtoPE(ProtectiveEarth).
（9）Outputcurrentandoutputwattagemustnotexceedtheratedvaluesonitsspecification.
（10）Disconnectsystemfromsupplyvoltage:
Beforecommencinganyinstallation,maintenanceormodificationwork:Disconnectyoursystemfrom
supplyvoltage.Makesurethatinadvertentconnectionincircuitwillbeimpossible!
（11）Forcontinuedprotectionagainstriskoffire,replaceonlywithsametypeandratingoffuse.
Pournepascompromettrelaprotectioncontrelesrisquéd’incendie,remplacerparunfusibledemême
typeetdememescaractéristiquesnominales.

Note.1:PollutionDegree2applieswherethereisonlynon‐conductivepollutionthatmighttemporarilybecome
conductiveduetooccasionalcondensation.Generallyrefertodry,well‐ventilatedlocations,suchas
controlcabinets.

Manufacturer：
MEANWELLENTERPRISESCo.,Ltd.
No.28,Wuquan3rdRoad,WuguDistrict,
NewTaipeiCity,Taiwan,24891
Tel: +886‐2‐2299‐6100
Web:www.meanwell.com

