Meanwell SHP-30K-HV Series User manual

SHP-30K-HV Series
30KW HVDC Power Supply
Installationmanual
3φ3-wire wide input range High efficiency Intelligent
Industrial
Security
EV
TelecomAutomate

SHP-30K-HV series is a 30KW input AC/DC power supply. This series operates forφ3W3
the wide range three phase AC input (3 phase 3 wire / 340~530VAC) neutral is not
needed, and offers the models with DC outputs (55V/115V/230V/380V) that mostly
demanded by various industries. Can be working at ambient temperature up to 70 with℃
forced air cooling. Moreover, SHP-30K-HV series provides vast design flexibility by
equipping various built-in functions such as output programming, active current sharing,
remote ON-OFF control, auxiliary power, and communication protocols, that will not only
satisfy marker demand, but also enhance automation purpose.

Contents
2023 10 Ver 0.2023 10 Ver 0.
1.Safety Guidelines
2.Introduction
2.1 Model Encoding
2.2 Features
2 3 Specification.
2 4 Derating curve.
25. Mechanical specification
3.Installation & Wiring
3.1 Mounting
3.2 Installation Notes
33. Cable Size Selection
3.4 AC Power Connection
4.Panel and LED Indicator
4.1 Panel Description
4.2 Pin Assignment of CN53
4 Pin Assignment of CN.3 86
Communication Address.44
/ ID Assignment
5.Operation
5. Inrush Current Limiting1
5. Power Factor Correction2
(PFC)
5. Output Voltage Adjustment3
5. Output Current Adjustment4
5. Parallel function5
5. Remote Control6
5.7 Alarm Signal Output
5. Auxiliary Output8
5.9 Factory Resetting
6.Communication Protocol
.16PMBus Communication
Interface
6.2 CANBus Communication
Interface
63.M us CommunicationODB
Interface
6.4 Value range and tolerance
7.Protections and Trouble
Shooting
7.1 Protections
7.2 Trouble Shooting
8.Warranty
1
2
2
3
4
6
7
8
8
9
9
10
11
11
12
12
14
15
15
15
15
17
18
20
20
21
21
22
22
28
39
53
55
55
56
57

1
11.Safety Guidelines
nRisk of electrical shock and energy hazard, all failure should be examined by a
qualified technician. Please do not remove the case form the power supply by
yourself.
nPlease do not change any component on the unit or make any kind of
modification on it.
nThe input voltage range of is 380~480Vac (50/60Hz), please do not3φ3-wire
feed in voltage that is over or less than 10% of that range.
nPlease do not stack any object on the unit.
nThe safety protection level of this supply is class I. The Frame "Ground" ( ) of
the unit must be well connected to PE (Protective Earth).
nThe device should be installed in a Restricted Access Location, such as electric
rooms that are accessible only to skilled persons.
2
2.Introduction
2.1 Model Encoding
2
Communication protocol option
Output voltage (55V/115V/230V/380V)
Output wattage
Series name
115SHP --30K
Type
Blank
-MOD
-PM
Communication Protocol
CANBus
PMBus
MODBus-RTU/RS-485
Note
By request
By request
In Stock

3
2.2 Features
2
l3φ3-wire / 340~530VAC wide input range without Neutral
lHigh efficiency up to 9 %7
lForced air cooling
lBuilt-in CAN us/Optional PMBus/Modbus-RTU/RS-485 protocolB
lOutput voltage and constant current level programmable
lActive current sharing up to units12 ()285KW
lBuilt-in remote ON-OFF control/ auxiliary power/ alarm signal
lProtections: Short circuit/ Overload/ Over voltage/ Over temperature/
Fan fail
lDouble insulation for 55V model
l5 years warranty
4
2
2.3 Specification
SHP-30K-55 SHP-30K-115 SHP-30K-230 SHP-30K-380
MODEL
OUTPUT
INPUT
ENVIRON-
MENT
PROTECTION
FUNCTION
DC VOLTAGE (factory default) 55V 115V 230V 380V
346A 261A 130.5A 79A
0 ~ 346A 0 ~ 261A 0 ~ 139A 0 ~ 90A
19000W 30000W 30000W 30000W
48 ~ 57.6V 115 ~ 138V 216 ~ 260V 334 ~ 400V
0.55Vp-p 1Vp-p 1.5Vp-p 2Vp-p
Can be adjusted via built-in potentiometer
39 ~ 57.6V 90 ~ 138V
145 ~ 166V
170 ~ 260V
273 ~ 312V
260 ~ 400V
420 ~ 480V
±1.0% ±1.0% ±1.0% ±1.0%
±0.5% ±0.5% ±0.5% ±0.5%
±0.5% ±0.5% ±0.5% ±0.5%
3000ms, 100ms at full load
20ms / 400VAC at 75% load 16ms / 400VAC at full load
3 3-wire / 340 ~ 530VACψ
-30 ~ + ")70 (Refer to “Derating Curve℃
47 ~ 63Hz
20 ~ 90% RH non-condensing
≧0.98/400VAC/480VAC at full load
-40 ~ +85 , 10 ~ 95% RH non-condensing℃
95% 96% 96.5% 97%
±℃ ℃)0.03%/ (0 ~ 50
30A/400VAC 25.2A/480VAC 47A/400VAC 39A/480VAC
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
60A/400VAC 80A/480VAC
<6.5mA peak / 530VAC
100 ~ 105% of rated current
Protection type : Constant current limiting, unit will shutdown after 5 sec. re-power on to recover
60.5 ~ 69.1V
Protection type :Shut down O/P voltage,re-power on to recover
Shut down O/P voltage, recovers automatically after temperature goes down
Up to 12 units or more. Please refer to the Current share derating curve
[email protected] tolerance 5%, ripple 150mVp-p±
Please refer to the Function Manual
AC-OK, DC-OK, Fan Fail. Please refer to the Function Manual.
The TTL signal output, PSU turn on = -0.5 ~ 0.5V ; PSU turn off = 3.5 ~ 5.5V
Please refer to the Function Manual
Adjustment of output voltage is allowable to between 50 ~ 120% of nominal output voltage
Please refer to the PV curve Function Manual
Adjustment of constant current level is allowable to between 1 ~ 100% of rated current
Please refer to the PC curve Function Manual
CURRENT (factory default)
RATED RANGE
RATED POWER (max.)
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
WORKING TEMP.
FREQUENCY RANGE
WORKING HUMIDITY
POWER FACTOR (Typ.)
STORAGE TEMP., HUMIDITY
EFFICIENCY (Typ.)
TEMP. COEFFICIENT
AC CURRENT (Typ.)
VIBRATION
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVERLOAD
OVER VOLTAGE
OVER TEMPERATURE
CURRENT SHARING
AUXILIARY POWER(AUX)
REMOTE ON-OFF CONTROL
ALARM SIGNAL OUTPUT
DC-OK SIGNAL
OUTPUT VOLTAGE
PROGRAMMABLE
CONSTANT CURRENT
LEVEL PROGRAMMABLE
FULL POWER VOLTAGE RANGE
RIPPLE & NOISE (max.)
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE
Note.2
Note.3
Note.5
Note.6

2
5
SAFETY &
EMC
(Note.7)
OTHERS
NOTE
SAFETY STANDARDS
I/P-O/P:4.25KVAC I/P-FG:3KVAC O/P-FG:3KVAC
UL62368-1, IEC62477, CAN/CSA C22.2 , TUV BS EN/EN62368-1 EAC TP TC 004 aNo. 62368-1 , pproved
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
188.1K hrs min. Telcordia SR-332 (Bellcore) ; 20.9K hrs min. MIL-HDBK-217F (25 )℃
540*424*83.5mm (L*W*H)
23.4Kg; 1pcs/23.4Kg/2.82CUFT
EN55024 , EN61204-3, EN61000-6-2
Parameter
Parameter
Standard
Standard
BS EN/EN55032 (CISPR32) / EN55011 (CISPR11)
BS EN/EN55032 (CISPR32) / EN55011 (CISPR11)
BS EN/EN61000-4-2
BS EN/EN61000-4-3
BS EN/EN61000-3-2
BS EN/EN61000-4-4
BS EN/EN61000-4-6
BS EN/EN61000-4-11
BS EN/EN61000-3-3
BS EN/EN61000-4-5
BS EN/EN61000-4-8
Test Level / Note
Test Level / Note
Class A
Level 3, 8KV air ; Level 2, 4KV contact
Class A
Level 3
Level 3
Level 3
>95% dip 0.5 periods, 30% dip 25 periods,
>95% interruptions 250 periods
-----
-----
Level 4, 4KV/Line-Earth ; Level 3, 2KV/Line-Line
Level 4
Conducted
ESD
Radiated
Radiated
Harmonic Current
EFT / Burst
Conducted
Voltage Dips and Interruptions
Voltage Flicker
Surge
Magnetic Field
WITHSTAND VOLTAGE Note.4
Note.4
ISOLATION RESISTANCE
MTBF
DIMENSION
PACKING
1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance :includes set up tolerance, line regulation and load regulation.
4. During withstand voltage and isolation resistance testing, the screw “A” shall be temporarily removed, and shall be installed back after the testing.
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
6. The efficiency is measured 75% at 480VAC input.
7. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit
on mm* mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.a 600 900 For guidance on
how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com)
8. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m℃℃
(6500ft).
9. If use PV signal to adjust Vo, under certain operations conditions, ripple noise of Vo might slightly go over rating defined in this specification.
01 . Under light load condition, output voltage ripple will exceed specification. The behavior can be minimized by increasing the load.
Product Liability Disclaimer For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx※：
EMC EMISSION
EMC IMMUNITY
6
2.4 erating curveD
AMBIENT TEMPERATURE ( )℃
LOAD (%)
-30 010 20 30 40 45 50 60 70 (HORIZONTAL)
20
40
50
60
80
100
2
Others
55V

7
2
2.5 Mechanical specification
※Mounting Instruction
Recommended Screw Size MAX. Penetration Depth LRecommended mounting torque
5mm
M4 7~1 Kgf-cm0
Mounting Screw
Mounting Surface Chassis of SHP-30K
Hole No.
1
7.1
7
7.4
68.75
4-M4 L=5mm
4-M4 L=5mm
4-M4 L=5mm
21
488
540
21
488
540
40 max.
10 max.
+V
-V
3
15 max.
75434
8
36 54 72 9
1
10 3 85 67 4
10
1
9
2
12
11
14
13
16
15
1820
1719
CN86
CN53
SVR
SW51
SW51
LED
CN86
19
20
1
2
SVR
SW52
SW52
1
2
3
FG
Screw "A"
TB1
M5
Air flow
direction
1
1
1
1
1
1
22.7 22.7
38 38
12
16
2 8.5-ψ
25
4-M4
10.2
483.6
466.1
83.5
46.75
46.75
331.6
331.6
424
(Note.4)
DIP-SW
1 2 3 1
2
9
10
CN53
8
3.1 Mounting
3.Installation & Wiring
3.1.1 Normal Mounting
Suggested mounting on horizontal surfaces.
3.1.2 System power cabinet
Horizontal mounting
3
(Front View) (Side View) (Back View)
Item ItemDescription Description
AECMU2 Smart Controller AC Input Circuit Breaker
SHP-30K-HV Power Supply DC Output Terminal
30U Cabinet AC Input Terminal Block
RJ-45 port
BF
CG
D
750450
!
F1
F3
F2
F4
HOT KEY
Enter
1579
A
D
B
C
E
F
G

9
3
3.2 Installation Notes
A. Before any installation or maintenance work, please disconnect your
system from the utility. Ensure that it cannot be re-connected to the
utility inadvertently.
B. Keep enough insulation distance between mounting screws and
internal components of power supplies. Please refer to 2.5 Mechanical
specification to receive the maximum length of mounting screw
C. Mounting methods other than chapter 3.1 or operate under high
ambient temperature may increase the internal component
temperature and will require a de-rating in output current.
D. Fans and ventilation holes must be kept free from any obstructions.
Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
Cable connections should be as short as possible and make sure that
suitable cables are chosen based on safety requirement and rating of
current. Small cross section will result in lower efficiency, less output
power and the cables may also become overheated and cause danger. For
selection, please refer to table 3-1.
33.Cable Size Selection
6A 6-10A 10-16A 16-25A 25-32A 32-40A 40-63A 63-80A 80-100A
0.75 1.00 1.5 2.5 4 6 10 16 25
Suggest current
(Amp)
Cross-section of
lead(mm )
2
Note: Current each wire carries should be de-rated to 80% of the current
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
AWG 18161412108642
Table 3-1 cable recommendations
10
3.4 AC Power Connection
Figure 1
Figure 2
◎340VAC~530VAC/△3φ3-wire
340V~530VAC
340V~530VAC
TSHP-30K-HV
SHP-30K-HV
S
RFG
L1
L2
L3
◎/ Y 340VAC~530VAC3φ3-wire
T
S
R
FG
L1
L2
L3
340V~530VAC
340V~530VAC
3

11
4.Panel and LED Indicator
4.1 Panel Description
AC input terminals
DC output terminals
DIP-SW:
Function pins:
LED indictor:
SVRs:
SW51, SW52:
A
AFG
BCED
B
C
D
E
F
G
Used for parallel control/PV/PC functions
Used for control and monitoring functions. Please refer to 4.2 and 4.3.
Indicate the status of the supply and load condition.s
Used to adjust output voltage. The one on the top for fine-tune,
the other for coarse-tune.
Used for assigning a device address or CAN ID when the communication
interface is used. Please refer to 4.4 for detail.
4
12
4.2 Pin Assignment of CN53
9
10
1
2
Pin No.
1,2
3,4
5,6
7,8
9,10
Function
-V(Signal)
PV+
PC+
DB
DA
Description
Negative output voltage signal. It is for local sense and certain
function reference; it cannot be connected directly to the load.
Connection for output voltage programming. (Note)
Connection for constant current level programming. (Note)
Differential digital signal for parallel control. (Note)
Note: Non-isolated signal, referenced to [-V(Signal)].
-V(Signal)-V(Signal)
PV+PV+
DBDB
DADA
PC+PC+
9
1
10
2
4.3 Pin Assignment of CN86
GND-AUX GND-AUX
DC-OK
AC-OK
SCL/CANL/
DATA-
SCL/CANL/
DATA-
SDA/CANH/
DATA+
SDA/CANH/
DATA+
+12V-AUX +12V-AUX
GND-AUX
GND-AUX
GND-AUX
GND-AUX
T-ALARM
RLRL
+5V-AUX
Remote
ON-OFF
Fan Fail
19
1
20
2
2
1
20
19
4

13
Pin No.
3
4
5
6,8,10,12
1,2
13,14
15,16
7
17,18
19,20
9
11
Function
Remote
ON-OFF
+5V-AUX
T-ALARM
GND-AUX
RL
Fan Fail
+12V-AUX
GND-AUX
DC OK
AC-OK
SCL
SDA
CANL
CANH
DATA-
DATA+
Description
The unit can turn the output ON/OFF by dry contact between
Remote ON/OFF and +5-AUX.(Note)
Short (4.5 ~ 5.5V) : Power ON ; Open(0 ~ 0.5V) : Power OFF ;
The maximum input voltage is 5.5V
Auxiliary voltage output, 4.5~5.5V, referenced to GND-AUX
(pin 6,8,10,12,19,20) only for Remote ON/OFF used. This output
is not controlled by the Remote ON/OFF control.
Short: Termination resistors(120 ) For CANBus MODBusΩ、、
Communication, please use Jumper (pin1,2)
Note: Isolated signal, referenced to (GND-AUX).
4High (3.5 ~ 5.5V) : When the internal temperature exceeds
the limit of temperature alarm.
Low (-0.5 ~ 0.5V) : When the internal temperature is normal.
The maximum sourcing current is 10mA and only for output.(Note)
The maximum sourcing current is 10mA and only for output.(Note)
The maximum sourcing current is 10mA and only for output.(Note)
The maximum sourcing current is 10mA and only for output.(Note)
High(3.5~5.5V):When the fan fail.
Low(-0.5~0.5V):When the fan works normally.
High(3.5 ~ 5.5V) : When Vout 80% 6%.≦±
Low(-0.5 ~ 0.5V) : When Vout 80% 6%≧±
.
High (3.5 ~ 5.5V): When AC input 335 1.5%Vac, PSU works normally.≧±
Low (-0.5 ~ 0.5V): When AC input 320 1.5%Vac, PSU shut down.≦±
Auxiliary voltage output GND.
The signal return is isolated from the output terminals (+V & -V).
For PMBus model: Serial Clock used in the PMBus interface.(Note)
For PMBus model: Serial Clock used in the PMBus interface.(Note)
For CANBus model: Data line used in CANBus interface.(Note)
For CANBus model: Data line used in CANBus interface.(Note)
For MODBus model: Data line used in MODBus interface.(Note)
For MODBus model: Data line used in MODBus interface.(Note)
Auxiliary voltage output, 11.4~12.6V, referenced to
GND-AUX (pin19 & 20).
The maximum load current is 1.5A. This output is not controlled
by “Remote ON-OFF”.
Auxiliary voltage output GND.
The signal return is isolated from the output terminals(+V & -V).
14
Model No. Model No.
0
33
32
1
342
353
364
375
386
397
408
419
4210
4311
4412
4513
4614
4715
4816
4917
5018
5119
5220
5321
5422
5523
5624
5725
5826
5927
6028
6129
6230
6331
Switch position Switch position
SW51
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
3
3
SW51
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
6
6
5
5
5
5
5
5
5
5
6
6
SW52
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
SW52
3
4
5
6
7
2
8
9
0
1
2
3
4
5
6
7
8
9
8
9
1
0
7
6
5
4
3
2
1
0
2
3
Table 4-1
4
4. Communication Address/ID Assignment4
Each - - unit should have their unique and own device address to communicate over theSHP 30K HV
CANBus, . SW51 and S 52 allow users to designate an address for thePMBus or MODBus W or ID
supply the table detailed settingsunits (with maximum of 64 addresses). Please refer to below for .

15
5.Operation
5.1 Inrush Current Limiting
5.2 (PFC)Power Factor Correction
5.3Output Voltage Adjustment
●Built-in AC inrush current limiting circuit.
●Since the inrush current limiting circuit mainly consists of a NTC
thermistor and a relay, inrush current will be much higher than the
specified value if the thermistor is not allowed sufficient time to
cool down. After turning off the supply, a 10 second cool down
period is recommended before turning on again.
●Built-in active power factor correction (PFC) function, power factor
(PF) will be 0.98 or better at full load condition. PF will be less than
0.98 if it is not at full load condition.
●Output voltage can be adjusted via SVR, PV or communication
interface.
A.Set DIP switch 3 to OFF position
B.Output voltage can be trimmed by the SVRs T.he one on the top for
fine-tune, the other for coarse-tune, please refer to illustration
below.
5. .13SVR
Figure 51-
ON
OFF
123
()fine-tune
()coarse-tune
DIP SW1
5
16
A.Set DIP switch 3 to ON position
B.Connect output of external DC source to PV+ and ,the an -V(signal)
as shown in Figure 5-2.
C.Relationship between output voltage and external DC source is
shown in Figure 5-3.
D.When increasing the output to a higher voltage level, please
reduce the loading current accordingly. Output wattage of the unit
should not exceed the rated value under any circumstance.
5.3.2 PV (Output Voltage Programming)
ON
OFF
123
Figure 52-
OUTPUT VOLTAGE(%)
◎The rated current should change with the
Output Voltage Programming accordingly.
◎he 100% output voltage is 48V/115V/T
216V/334V
OUTPUT CURRENT (%)
OUTPUT VOLTAGE
Figure 53-
LOAD
EXTERNAL VOLTAGE (DC)(0~5V)
()fine-tune
()coarse-tune
+V
-V
PIN3,4 PV+
PIN1,2 -V(Signal)
DIP SW1
50
100
120
Vout
014 4.41 4.37
V
4.7 4.8
113.7
114.5
106.5 380V(Default)
55V(Default)
230V(Default)
Non-Linear
3.64
115V(Default)
5
100
40
for 55V model
60
70
80
83.3
95.5
20
V
103.5
300.6
194.4
57.5 115V
167 380V
108 230V
43.2
115
334
216
48
138
400
260
57.655
24 55V

17
Figure 54-
LOAD
EXTERNAL VOLTAGE (DC)(0~5V)
+V
-V
PIN5,6 PC+
PIN1,2 -V(Signal)
DIP SW1
5
5.3.3 Communication
Output voltage can be adjusted through communication interfaces:
PMBus, CAN bus or Modbus. Please refer to chapter 6 for detailed
information.
5.4 Output Current Adjustment
●Output current can be adjusted via PC and communication interface.
A. Overload Protection(OLP)Default setting is at
5.4.1 PC (Output Current Programming)
ON
OFF
123
ON
OFF
123
B.To enable Constant Current Level Programming, Set DIP switch 2 to
OFF position
C Connect output of external DC source to PC+ and -V(signal),.the an
as shown in Figure 5-4.
D.Relationship between output current and external DC source I
shown in Figure 5-5.
E Auto de-rating function covered by over temperature protection, it.
works either in PC mode or under control by communication
protocol.
T1(Typ.): Maximum ambient temperature of full load
T2(Typ.): T1+5℃
18
Figure 55-
Non-Linear
()HORIZONTAL
T1T2
20
40
50
60
80
100
AMBIENT TEMPERATURE ( )℃
LOAD (%)
1
OUTPUT CURRENT(%)
100
110
Iout
0
EXTERNAL VOLTAGE (DC)
0.047 4.7
V
4.8
Non-Linear
5.5 Parallel function
55..1DA, DB signal and parallel control function
(1)Non-parallel operation
A Set DIP switch 1 to OFF position.
(2)Parallel operation
A Set DIP switch 1 to ON position.
B.By default, non-parallel operation
B.PSUs are configured in parallel operation.
ON
OFF
123
ON
OFF
123
Figure 56-
◎The 100% output current is 346A/261A/139A/90A
◎It might cause higher current ripple when the output current
adjust below 20%(@<1V programming)
DIP SW1
5

19
SHP-30K-HV has the built-in active current sharing function and can be connected in parallel, up
to 12 units or more, to provide higher output power as exhibited below :
◎The power supplies should be paralleled using short and large diameter wiring and then
connected to the load.
◎In parallel connection, power supply with the highest output Voltage will be the master unit
and its Vout will be the DC bus voltage.
◎The total output current must not exceed the value determined by the following equation:
Maximum output current at parallel operation = (Rated current per unit) x (Number of unit) x
95% when parallel unit less than 4.；
Maximum output current at parallel operation = (Rated current per unit) x (Number of unit) x
[95% - (Number of unit - 4) x 2%] when parallel unit more than 5.；
◎When the total output current is less than 5% of the total rated current, or say (5% of Rated
current per unit) (Number of unit) the current shared among units may not be balanced.×
(Please refer to the current share dreating curve)
◎Under parallel operation ripple of the output voltage may be higher than the SPEC at light
load condition. It will go back to normal ripple level once the
output load is more than 5%.
◎CN53/SW1 Function pin connection
◎DA,DB are connected mutually in parallel
5. .52
(V : CN53 connected ; X : CN53 not connected.)
..........
Figure 57-
DA DA DA DADB DB DB DB
If the lines of CN53 are too long, they should be twisted in pairs to avoid the noise
PSU1
CN53
PSU2
CN53
PSU11
CN53
PSU12
CN53
88 8810 10 10 10
DA DA DA DADB DB DB DB
77 7799 99
.......
PSU1 PSU2 PSU11 PSU12
LOAD
+V -V
Parallel
1 unit
2 unit
3 unit
4 unit
5 unit
6 unit
7 unit
8 unit
9 unit
10 unit
11 un it
12 unit
PSU1 PSU2 PSU3 PSU4 PSU5 PSU6 PSU7 PSU8 PSU9 PSU10 PSU11 PSU12
CN53 CN53 CN53 CN53 CN53 CN53 CN53 CN53 CN53 CN53 CN53 CN53
X
VV
VVV
VVVV
VVVVVON
VVVVVOFF
OFF
OFF
OFF
OFF
OFF
OFF
VON
VVVVVVOFFVON
VVVVVVV
OFFOFF VON
VVVVVVVVOFFOFFOFF V ON
VVVVVVVVOFFOFFOFF V OFF V ON
VVVVVVVVOFFOFFOFF V OFF V OFF V ON
VVVVVVVVOFFOFFOFF V OFF V OFF V OFF V ON
ON
ON ON
OFF ON
ONOFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1 SW1 PIN1
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣
∣∣
5
20
5.7 Alarm Signal Output
●There are 4 alarm signals, DC-OK, T-ALARM, Fan Fail and AC-OK, in
TTL signal form, on CN86. These signals are isolated from output.
5. Remote Control6
●The power supply can be turned ON-OFF by using the "Remote
ON-OFF" function.
Figure 58-
Figure 59-
Between Remote ON-OFF(CN86 pin1) and 5V-AUX(CN86 pin2) Status
Switch close (Short) power supply ON
Switch open (Open) power supply OFF
DC-OK & T-ALARM & Fan Fail Signal
AC-OK Signal
Power Supply Status
Power Supply Status
“High” >3.5~5.5V
“High” >3.5~5.5V
“Low” <-0.5~0.5V
“Low” <-0.5~0.5V
OFF
ON
ON
OFF
PIN4 +5V-AUX
PIN3 Remote ON-OFF
CN86
DIP
SW1
SW52
SW51
CN53
Application
Circuit
CN86
DIP
SW1
SW52
SW51
CN53
PIN6,8,10,12 GND-AUX
PIN5 T-ALARM
PIN7 Fan Fail
PIN9 DC-OK
PIN11 AC-OK
5

21
5.8 Auxiliary Output
●B5uilt-in 12V/1. A auxiliary output
+12V-AUX GND-AUXto 12Vdc
5.9 Factory Resetting
●Users can follow the steps below to restore factory settings for
commands: VOUT_TRIM(VOUT_SET), IOUT_OC_FAULT_LIMIT(IOUT_SET) ,
OPERATION, SYSTEM_CONFIG and all charge configurations.
(1) Set the rotary switch of SW52 to position " ".0
(2) Power on the supply in REMOTE OFF mode (no output at this step).
(3) After power on, within 15 seconds, switch SW52 from " " topositions 0
po "7"and then switch it back to " "sitions position 0 .
(4) Green LED will blink 3 times if set successfully.it is
(5) Factory default setting will be restored after re-power on.
Figure 510-
& 18 +12V-AUXPIN17
PIN19 & 20 GND-AUX
CN86
DIP
SW1
SW52
SW51
CN53
5
SW52
22
◎SHP- 0K-3HVis compliant with PMBus Rev.1.1, the maximum
communication speed is 100KHz and has the capability of identifying
up to 4 addressed units.6
◎PMBus communication interface is able to provide the current
operating status and information. Supported information is as below:
1. Output voltage, current and internal temperature
2. Alarm and status.
3. Manufacturer and mode data.
Each SHP- 0K- unit should have their unique and own device3HV
address to communicate over the PMBus. 7-bit address setting is
used to assign advice address, shown in the description below.
Please refer to 4.4 Communication Address/ID Assignment for
address setting.
6.1 PMBus Communication Interface
611.. PMBus Device Addressing
1 A5A4A3A2A1A0
MSB LSB
6.Communication Protocol
●There are two means to control the unit, analog signals and digital
communication. Analog is the default setting for the unit, signals
including PV, PC and SVR can be used immediately once receiving the
unit. The digital communication (PMBus, CANBus or MODBus) is initially
uncontrollable but readable. To activate the adjustment commands of
OPERATRION, VOUT_TRIM or VOUT_SET.., ect., set
PM_CTRL/CAN_CTRL/MOD_CTRL of SYSTEM_CONFIG (PMBus: BEh;
CANBus: 0x00C2; MODBus: 0x00C4) at 1 and then reboot the unit. Once""
the digital communication dominates the unit, the analog signals
become invalid.
6
◎The command list of the SHP- 0K- is shown in Table 6- . It is3HV 1
compliant with the standard protocol of PMBus Rev. 1.1.
For detailed information, please refer to PMBus official website
(http://pmbus.org/specs.html).
612.. PMBus Command List

23
Table 6-1
Command
Code
01h
00h
02h
19h
20h
21h
# of data
Bytes
1
1
1
1
1
2
Description
Command
Name
OPERATION
PAGE
ON_OFF_CONFIG
CAPABILITY
VOUT_MODE
VOUT_COMMAND
Transaction
Type
Page
R/W Byte
R/W ByteAll
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
All
0
0
1
1
2
2
Read Byte
Read Byte
Read Byte
22h 2VOUT_TRIM R/W Word
R/W Word
47h
79h
7Ah
7Bh
7Ch
7Dh
1
2
1
1
1
1
IOUT_OC_FAULT_RESPONSE
STATUS_WORD
STATUS_VOUT
STATUS_IOUT
STATUS_INPUT
STATUS_TEMPERATURE
Read Byte
Read Word
Read Byte
Read Byte
Read Byte
Read Byte
Read Byte
Read Byte
Read Byte
7Eh 1STATUS_CML
46h 2IOUT_OC_FAULT_LIMIT R/W Word
80h
81h
88h
88h
88h
89h
89h
89h
8Bh
8Ch
1
1
2
2
2
2
2
2
2
2
STATUS_MFR_SPECIFIC
STATUS_FANS_1_2
READ_VIN
READ_VIN
READ_VIN
READ_IIN
READ_IIN
READ_IIN
READ_VOUT
READ_IOUT
Read Word
Read Word
Read Word
Read Word
Read Word
Read Word
Read Word
Read Word
98h 1PMBUS_REVISION Read Byte
8Dh 2READ_TEMPERATURE_1 Read Word
99h
90h
92h
91h
93h
9Ah
9Bh
9Ch
9Dh
9Eh
BEh
BFh
12
2
2
2
2
12
24
3
6
12
2
2
MFR_ID
READ_FAN_SPEED_1
READ_FAN_SPEED_3
READ_FAN_SPEED_2
READ_FAN_SPEED_4
MFR_MODEL
MFR_REVISION
MFR_LOCATION
MFR_DATE
MFR_SERIAL
SYSTEM_CONFIG
SYSTEM_STATUS
Block Read
Read Word
Read Word
Read Word
Read Word
Block Read
Block Read
Block R/W
R/W Word
Read Word
Block R/W
Block R/W
6
Remote ON/OFF control
Page
ON/OFF function configuration
Capabilities of a PMBus device
Summary status reporting
Output voltage status reporting
Output current status reporting
AC input voltage status reporting
Temperature status reporting
Communication, logic, Memory status reporting
Manufacture specific status reporting
Fan1 and 2 status reporting
The compliant revision of the PMBus
Manufacturer's name
Fan speed 1 reading value
Fan speed 2 reading value
Fan speed 3 reading value
Fan speed 4 reading value
Manufacturer's model name
Firmware revision
Manufacturer's factory location
Manufacture date
Product serial number
System setting
System status
Define data format for output voltage
(format: Linear 16, N= -6)
Define data format for output voltage
(format: Linear 16, N= -6)
Output voltage trimmed value
(format: Linear 16, N= -6)
Output overcurrent setting value
(format: Linear 11, N= -2)
Output voltage reading value
(format: , N= -6)Linear 16
Output current reading value
(format: Linear 11, N= -2)
Define protection and response when an
output overcurrent fault occurred
VRS input voltage reading value
(,=0)format: Linear 11 N
VST input voltage reading value
(,=0)format: Linear 11 N
VTR input voltage reading value
(,=0)format: Linear 11 N
Rinput current reading value
(,=)format: Linear 11 N -5
Sinput current reading value
(,=)format: Linear 11 N -5
Tinput current reading value
(,=)format: Linear 11 N -5
Temperature 1 reading value
(format: Linear 11, N= -3)
24
6
Bit7
Bit7
Bit6
Bit6
Bit5
Bit5
Bit4
Bit4
Bit3
Bit3
Bit2
Bit2
Bit1
Bit1
Bit0
Bit0
High byte -
-
-
-
-
EEPER ADL_ON
INITIAL_
STATE
-- -
-
-
PFC OK_
--
MS/
Low byte
Low byte
---OPERATION_INIT PM_CTRL
DC_OK
Low byte
Bit 0 PM_CTRL: PMBus Control Selection
Bit 1: DC_OK : Secondary DD output voltage status
Bit 2: P _OK :
FC Primary PFC status
Bit 0: M/S : Parallel mode status
Bit 1: 2 OPERATION_INIT : OPERATION_INIT : Initial Operational Behavior
0b00＝Power on with 0x00: OFF
0b01＝Power on with 0x80: ON(default)
0b10＝Power on with the last setting
0b11＝Not used
Note: Unsupported settings display with "0"
0＝Output voltage and current controlled by SVR/PV/PC (default)
0TOOLOW＝Secondary DD output voltage status
0＝Primary PFC OFF or abnormal
0＝Current device is Slave
1＝Output voltage, current and remote ON/OFF controlled by PMBus
(VOUT_TRIM IOUT_FAULT_LIMIT OPERATION)、、
1＝Secondary DD output voltage status NORMAL
1＝Primary PFC ON normally
1＝Current device is Master
◎Definition of Command BEh SYSTEM_CONFIG :
◎Definition of Command BFh SYSTEM_STATUS:
Bit 4 ADL_ON : Active dummy load control status
Bit 5 INITIAL_STATE : Device initialized status
0＝Active dummy load off
1＝In initialization status
1 Active dummy load＝on
0＝NOT in initialization status
Note: Unsupported settings display with "0"

25
6
Bit 6 EEPER: EEPROM data access error
0 EEPROM＝ data access normal
1 EEPROM＝ data access error
Note:
1.When an EEPROM data access error occurs, the supply shuts down and
then entering protection mode with the LED indicator off. It only can be
recovered after the EEPROM error condition is resolved.
2.Unsupported settings display with "0"
6.1.3 Notes on PMBus
1 Insert a at least 50msec delay between commands..
2.Examples for Format Conversion:
(1) LINEAR16 format: VOUT_COMMAND, VOUT_TRIM, READ_VOUT.
For example:
Vo_real (actual output voltage) = V x 2 , V is from READ_VOUT.
N
If VOUT_MODE = 0x17, meaning N is -9. READ_VOUT is 0x3000 12288, then→
Vo_real = = 24.0V12288 × 2-9 .
Linear Format Data Bytes
The Mode bits are set to 000b.
The Voltage, in volts, is calculated from the equation:
2N Voltage V=
Where:
Voltage is the parameter of interest in volts;
V is a 16 bit unsigned binary integer; and
N is a 5 bit two' complement binary integer.s
(2)LINEAR11 format: IOUT_OC_FAULT_LIMIT, READ_VIN、READ_IIN,
READ_IOUT, READ_TEMPERATURE_1, READ_FAN_SPEED_1,
READ_FAN_SPEED_2, READ_FAN_SPEED_ , READ_FAN_SPEED_ .34
26
For example:
Io_real (actual output current) = Y 2 , Y is from READ_IOUT.× N
If READ_IOUT is 0xF188, meaning N is -2 and Y is 0x0188. Y is 0x0188 →
392, then Io_real = = 98.0A392 × 2-2 .
The following steps will describe how to set the SHP-30K-55 to 56V.
1.Set the address of the supply to 0""
7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0
N Y
Data Byte High Data Byte Low
MSB
MSB
Linear Data Format Data Bytes Y, N and the "real world" value is:
The relation between
X=Y 2
N
Where, as described above:
X is the "real world" value;
Y is an 11 bit, two' complement integer; ands
N is a 5 bit, two' complement integer.s
Devices that use the Linear format must accept and be able to process any value of .N
6
.Practical Operation3
SW51 SW52
.2 Connect the SDA, SCL and GND pins of the master to the
corresponding SDA (PIN15) SCL (PIN13) and GND-AUX (PIN19) of,
CN86 on the supply
◎Set speed: 100KHz
3.Configure communication settings after power on. Enable
communication mode and set power ON when AC connected.
Command code: 0xBE(SYSTEM_CONFIG)
Data: 0x03(Lo) + 0x00(Hi)。Please refer to definition of SYSTEM_
CONFIG for detailed information.
SHP-30K-HV
SDA(CN86)
15
13
19
SDA
SCL(CN86)SCL
GND-AUX(CN86)GND
Controllor
Address(7 bit)
0x40
Operation
Write 0xBE
Command Code Data
0x , 0x0003

27
4.Set Output voltage to 56V.
Command code: 0x22(VOUT_TRIM)
Data: 1V 0x0040 0x40(Lo) + 0x00(Hi)→→
NOTE: VOUT_TRIM is LINEAR16 forma
Address(7 bit)
0x40
Operation
Write 0x22
Command Code Data
0x , 0x40 00
5.It is recommended to review all of the settings and parameters using
the appropriate commands. In the event that they do not meet your
requirements, you may rewrite them as needed. EX: Read VOUT_TRIM
to check whether output voltage was set to a proper level.
6.Finally, check whether Remote ON-OFF (PIN4) and +5-AUX (PIN3) pins of the
CN86 connector are short-circuited if there is no output voltage.
Remote ON-OFF
CN86 +5V-AUX
SHP-30K-HV
4
3
Address(7 bit)
Address(7 bit)
Read VOUT_TRIM
The unit returns data below
Data: 0x40(Lo) + 0x00(Hi) 0x0040 64 × 2 1V→→
-6 =。
55V + 1V = 56V, the result is correct
0x40
0x40
Operation
Data
Read
0x 0, 0x 040
0x22
Command Code
6
●Physical layer specification
This protocol follows CAN ISO-11898 with Baud rate of 250Kbps.
●Data Frame
This protocol es Extended CAN 29-bit identifier frame format orus
CAN 2.0B.
6.2 CANBus Communication Interface
28
●Communication Timing
Min. request period (Controller to SHP-30K-HV): 50mSec。
。Max. response time (SHP-30K-HV to Controller): 12.5mSec
。Min. packet margin time (Controller to SHP-30K-HV): 12.5mSec
PSU CAN-RX
(form Controller)
PSU CAN-TX
Request period
(Controller to PSU/CHG)
Response time
(PSU/CHG to Controller)
RX data
TX data
RX data
Packet Margin time
(Controller to PSU/CHG)
6
COMD low byte.
COMD low byte.
COMD low byte.
COMD high byte.
COMD high byte.
COMD high byte.
Data low byte
Data low 1 .....
Data high byte
Data high 6
Data filed bytes
Data filed bytes
Data filed bytes
Response:
SHP to :Controller
NOTE: will not send data back when write parameters, such asSHP VOUT_SET
Read:
0
0
0
1
1
1
2
2
3
7
●Data Field Format
Controller to SHP
Write:

29
6.2.1 Message ID definition
Message ID
0xC00XX
0xC01XX
0xC01FF
NOTE: XX means the address of SHP- 0K3 -。HV Please refer to the
4.4 Communication Address/ID Assignment for detailed
CAN ID settings.
Description
SHP to Controller Message ID
Controller to SHP Message ID
Controller broadcasts toSHP Message ID
6
30
0x0080
0x0081
0x0083
0x0084
0x0082
0x0052
0x0053
0x0054
0x0055
0x0060
0x0061
0x0062
0x0070
0x0072
0x0071
0x0073
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
6
6
6
6
6
2
2
2
2
2
2
2
Internal ambient temperature
(format: value, F=0.1)
2
2
2
2
MFR_ID_B0B5
MFR_ID_B6B11
MFR_MODEL_B6B11
MFR_REVISION_B0B5
MFR_MODEL_B0B5
READ_VIN_TR
READ_ IN_IR
READ_ IN_IS
READ_ IN_IT
READ_VOUT
READ_IOUT
READ_
TEMPERATURE_1
READ_FAN_
SPEED_1
READ_FAN_
SPEED_3
READ_FAN_
SPEED_2
READ_FAN_
SPEED_4
Manufacture's name
Manufacture's name
Manufacture model name
Firmware version
Manufacture model name
VTR Input voltage read value
(format: vF1alue,=0.)
RInput read valuecurrent
(format: vF1alue,=0.)
SInput read valuecurrent
(format: vF1alue,=0.)
TInput read valuecurrent
(format: vF1alue,=0.)
Output voltage read value
(format: value, F=0.01)
Output current read value
(format: value, F=0.01)
Fan speed 1 reading value
(format: value, F=1)
Fan speed reading value3
(format: value, F=1)
Fan speed reading value2
(format: value, F=1)
Fan speed reading value4
(format: value, F=1)
Table 6-2
Command
Code
0x0000
0x0020
0x0030
R/W
R/W
R/W
1
2
2
OPERATION
VOUT_SET
IOUT_SET
Command
Name
Transaction
Type
# of data
Bytes Description
ON/OFF control
ON: 01h/OFF: 00h
Output voltage set
(format: value, F=0.01)
Output voltage set
(format: value, F=0.01)
0x0040
0x0050
0x0051
R
R
R
2
2
2
FAULT_STATUS
READ_VIN_RS
READ_VIN_ST
Abnormal status
VRS Input voltage read value
(format: vF1alue,=0.)
VST Input voltage read value
(format: vF1alue,=0.)
6
0x0085 R 3 MFR_LOCATION_B0B2
Manufacture place

31
Bit _ ：Fan locked flag0 FAN FAIL
0＝ orking normallyW
1＝Fan locked
Bit 1 OTP：Over temperature protection
0＝Internal temperature normal
1＝Internal temperature abnormal
Bit 2 OVP：DC over voltage protection
0＝DC voltage normal
1＝DC over voltage protected
Bit 3 OLP：DC over current protection
0＝DC current normal
1＝DC over current protected
Bit 4 SHORT：Short circuit protection
0＝Shorted circuit do not exist
1＝Shorted circuit protected
Bit 5 AC_FAIL：AC abnormal flag
0＝AC input range normal
1＝AC input range abnormal
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Low byte OVPOLPSHORTAC_FAILOP_OFFHI_TEMP OTP
FAN FAIL_
◎FAULT_STATUS (0x0040):
Note : The conversion of setting and reading values is defined as following:
Actual value = Communication reading value ×F actor (F value). Among
them, Factor needs to refer to the definition of SCALING_FACTOR in
each model list.
EX: Vo_real (actual DC voltage) = READ_VOUT x Factor.
If the Factor of READ_VOUT of a certain model is 0.01, the
communication reading value is 0x0960 (hexadecimal)→2400
(decimal), then VDC_real = 2400 ×0 .01 = 24.00V.
0x00C2
0x00C1
R/W
R
2
2SYSTEM_STATUS
SYSTEM_CONFIG System configuration
System status
Command
Code
Command
Name
Transaction
Type
# of data
Bytes Description
6
0x00C0 R 6SCALING_FACTOR Scaling ratio
0x0086
0x0087
0x0088
R
R
R
6
6
6
MFR_DATE_B0B5
MFR_SERIAL_B0B5
MFR_SERIAL_B6B11
Manufacture date
Manufacture serial number
Manufacture serial number
32
◎MFR_MODEL_B0B5 (0x0082) is the first 6 codes of the manufacturer's
model name(ASCII); MFR_MODEL_B6B11 (0x0083) is the last 6 codes
of the manufacturer's model name (ASCII);
EX: →Model name is SHP- 0K-55 MFR_MODEL_B0B5 is SHP- 0；33
MFR_MODEL_B6B11 is K-55
◎MFR_REVISION_B0B5 ( ) is the firmware revision (hexadecimal).0x0084
A range of 0x00 (R00.0)~0xFE (R25.4) represents the firmware version
of an MCU; 0xFF represents no MCU existed.
EX: The supply has two MCUs, the firmware version of the MCU number
1 is version R25.4 (0xFE), the MCU number 2 is version R10.5 (0x69)
0x53
0xFE
0x4B
0x48
0x69
0x2D
0x50
0xFF
0x35
0x2D
0xFF 0xFF 0xFF
0x35
0x33
0x20
0x30
0x20
Byte 0
Byte 0
Byte 6
Byte 1
Byte 1
Byte 7
Byte 2
Byte 2
Byte 8
MFR_MODEL_B0B5
MFR_ID_B6B11
Byte 3
Byte 3
Byte 9
Byte 4
Byte 4
Byte 10
Byte 5
Byte 5
Byte 11
0x4D
0x4C
0x45
0x4C
0x41
0x20
0x4E
0x20
0x57
0x20
0x45
0x20
◎MFR_ID_B0B5 ( ) is the first 6 codes of the manufacturer's name0x0080
(ASCII);MFR_ID_B6B11 ( ) is the last 6 codes of the0x0081
manufacturer's name (ASCII)
EX: Manufacturer's name is MEANWELL→MFR_ID_B0B5 is MEANWE；
MFR_ID_B6B11 is LL
Byte 0
Byte 0
Byte 1
Byte 1
Byte 2
Byte 2
MFR_ID_B0B5
MFR_ID_B6B11
Byte 3
Byte 3
Byte 4
Byte 4
Byte 5
Byte 5
Bit 7 HI_TEMP：Internal high temperature protection
0＝Internal temperature normal
1＝Internal temperature abnormal
Note: Unsupported settings displays with "0"
6
Bit 6 OP_OFF：DC status
0＝DC output turned on
1＝DC output turned off

33
◎MFR_SERIAL_B0B5 ( ) and MFR_SERIAL_B6B11 ( ) are0x0087 0x0088
defined as manufacture date and manufacture serial number (ASCII)
EX: The first unit manufactured on 2018/01/01→MFR_SERIAL_B0B5:
；MFR_SERIAL_B6B11:180101 000001
0x31
0x30
0x38
0x30
0x30
0x30
0x31
0x30
0x30
0x30
0x31
0x31
Byte 0
Byte 6
Byte 1
Byte 7
Byte 2
Byte 8
Byte 3
Byte 9
Byte 4
Byte 10
Byte 5
Byte 11
0x31 0x38 0x30 0x31 0x30 0x31
Byte 0 Byte 1 Byte 2 Byte 3 Byte 4 Byte 5
◎MFR_DATE_B0B5 ( ) is manufacture date (ASCII)0x0086
EX: MFR_DATE_B0B5 is 180101, meaning 2018/01/01
◎SCALING_FACTOR ：(0x00C0)
Bit7
Bit7
Bit7
Bit7
Bit6
Bit6
Bit6
Bit6
Bit5
Bit5
Bit5
Bit5
Reserved
Reserved
FAN_SPEED Factor
IOUT Factor
IIN Factor
TEMPERATURE_1 Factor
VIN Factor
VOUT Factor
Bit4
Bit4
Bit4
Bit4
Bit7~Bit0
Reserved
Bit3
Bit3
Bit3
Bit3
Bit2
Bit2
Bit2
Bit2
Bit1
Bit1
Bit1
Bit1
Bit0
Bit0
Bit0
Bit0
byte4~5
byte3
byte2
byte1
byte0
byte0:
Bit 0:3 VOUT Factor：The factor of output voltage
0x =0Output voltage relevant commands not supported
0x4=0.001
0x5=0.01
0x6=0.1
0x7=1.0
0x8=10
0x9=100
6
34
Bit 4:7 IOUT Factor：The Factor of DC current
0x =0Output current relevant commands not supported
0x4=0.001
0x5=0.01
0x6=0.1
0x7=1.0
0x8=10
0x9=100
byte1:
Bit 0:3 VIN Factor：The Factor of AC input voltage
0x =0AC input relevant commands not supported
0x4=0.001
0x5=0.01
0x6=0.1
0x7=1.0
0x8=10
0x9=100
Bit 4:7 FAN_SPEED Factor：The Factor of fan speed
0x =0Fan speed relevant commands not supported
0x4=0.001
0x5=0.01
0x6=0.1
0x7=1.0
0x8=10
0x9=100
byte2:
Bit :3 TEMPERATURE_1 Factor：0The Factor of internal ambient temperature
0x =0Internal ambient temperature relevant commands not supported
0x4=0.001
0x5=0.01
0x6=0.1
0x7=1.0
0x8=10
0x9=100
6