Meanwell LCM-40(DA) User manual

Features
Wiring
Environmental limitations
Cautions
Settings and connections
1. Output Current Level Settings
‧
‧
‧
‧
‧
‧
‧
180~295VAC input only
Built-in active PFC
Output current level selectable by DIP switch
Built-in DALI interface and push dimming function (DA version)
Built-in 0~10Vdc a nd PWM signal dimming function (Non-DA version)
Power supply synchronization function up to 10 units
Temperature compensation function by external NTC
‧
‧
‧
‧
‧
‧
‧
Clas s po wer un it, ungrounded
Buil t-in 12V/50mA auxiliary output
Full plastic case enclos ed
No load power consumption <1W (1.2W for DA version)
Protection s: Short circuit / Over voltage / Over temperature
3 year warranty
Suit able for intell igent LED lighting
Ⅱ
‧
‧
‧
‧
Hous ing with cabl e clamp for re mote installation
Use wires with an adequate cro ss-section (see 5)
Use suitable mounting tools to do the wiring and mounting (see 5)
MCB circuit breaker) with an adequate current rating to protect the lighting system (see 6)
Use a (miniature
‧
‧
‧
Maximum ambient temperature must not exceed 60
Always allow adequate ventilation clearances, 50mm, aro und the unit in use to prevent it from overheating
Only install the unit in interior environments
℃
‧
‧
This unit must be installed by a qualified electrician
This unit is not suitable for applications that DC/DC converters are connected befor e LED lamps
The LCM can prov ide various output currents by setting the DIP switch. The settings of the DIP switch are shown in the tables below.
LCM-40(DA ) LCM-60(DA)
Note : 1.Fac tory d efault setting is 700mA.
2.Output vo ltage a nd output wattage must n ot exc eed the rated values.
Voltage
ran ge
Voltage
ran ge
1 12 23 34 45 56 6
Sel ectabl e
Current
Sel ectabl e
Current
2-100V 2-90V- -- - ----- ---- -- - ----- - --- -- - ----- ---
--- ---- -- - ----- - --- -- - ----- ---
- -- - ----- ---
--- ---
- -- - --
- -- - --
- -- - --
--- ---
O N O N
O N O NON ON
O N O NON ONO N O NON O N
O N ONON ONO N ONON ONON ON
O N O NON ONO N O NO N ONO N O NON ON
350mA 50 0mA
2-80V 2-90V50 0mA 60 0mA
2-67V 2-86V60 0mA 70 0mA*
2-57V 2-67V70 0mA* 90 0mA
2-4 5V 2-57V90 0mA 10 50mA
2-4 0V 2-42V10 50mA 14 00mA
LCM-40(DA), LCM-60(DA) installation manual
ON
6 5 4 3 2 1
-Vo
+Vo
SY N.
+
-NT C
+DI M
-DI M
+NT C
-FAN
+FAN
+
DA-
DA+
PUS H
AC / N
AC / L
Terminal blocks assignment for LCM
2. Connection of LED Lamps
Press down the "push bu tton" by a slo tted screw driver to insert or rem ove the cable .
Vo-
Vo+
AC/N
AC/L
NEU TRAL (Blue o r whit e)
LIVE (Br ow n or bl ack )
http: //www.meanwell.c om

  

123.5mm 23mm

3. Connection of Dimming Functions
4. NTC Connection
5. Recommended Scre wdriver, Wire and Torque Setting
6. Suggested Maximum Number of the LCM Units that can be Connected to a MCB (miniature circuit breaker ) at 230Vac
a. 0-10Vdc or 10V PWM (non-DA version only)
c. Push dim (DA version only)
d. Synchronization ope ration
The lights LCM units (slav es) can be dimmed synchronously through a LCM unit (the master) dire ctly controlled via
driven by
0-10Vdc, 10V PWM, DALI or push d im dimming function. The wiring is show n as b elow.
No te: ON LY use open push button witho ut indicator light.
Warning: Risk of short circuit. The push button can only be linked betwee n the PUSH and the AC/L (brown or bla ck).
DO NOT connect the push button to the AC/N (blue or white).
b. DALI (DA version only)
Note : Maximum DALI cable length is 300m
(based on a 1.5mm or 14AWG cable)
2
DA+
DA- D ALI
cont rol ler
Dimming control mechanism
Function
Turn ON/OFF
Dim UP/DOWN
Reset
None
Pushing time
0.1 ~ 1 sec
1.5 ~ 10 sec
> 11 sec
< 0.05 sec
SYN.
+
-
+
-
SYN.
+
-
+
-
SYN.
+
-
+
-
Master Slave 1 Slave 2
‧
‧
‧
Mating housing for SYN. connectors : JST B2B-XH or equivalent
Maximum number of the LCM units : 10 (1 master + 9 slaves)
Maximum cable length between each units : 20m (based on a cable with cross-section of 0.15mm ~0.3mm or AWG No. of 22 ~ 26)
2 2
Note 1 : DO NOT conne ct dimming circuitry to slaves.
Note 2 : Pl ease make sure all units are set to 100% dimming setting (factory default) befo re synchronizing.
Note: These calcu lated v alues are ba sed on MCB S201 series manufactured by A BB.
http: //www.meanwell.c om
Type
Model B10 B16 C1 0 C16
LCM-4 0(DA) 10 16 1 7 28
LCM-6 0(DA) 9 15 16 26
Solid wire
Stranded wire
Ameri can w ire gau ge
Wire strippi ng length
Screwdriver
Recommended tightening tor que
Suggested push-down strength
-----
-----
-----
-----
6mm Phillips
4.6 kgf-cm (4 lb-in)
-----
The cover
(the blue one)
Push terminal
(ACL/N, PUSH, DA , Vo )± ±
ψ ψ1.024 - 1.628mm
0.823 - 2.08mm2
14 - 1 8AWG
10mm (0.39")
3mm Phillips
-----
3 - 4 kp (6.61-8.81 lb )
F
‧
‧
It will always dim up when light intensity is lower than 10%, whe reas it will
Factory dim ming setting: 100%
always dim down when light intensity is higher than 90%
DIM-
DIM+ 0~ 10V DC
+
-
NTC-
NTC+
AC/L
AC/N
Push Bu tto nPUSH
LIVE (Brow n or black)
NEUTRAL (Bl ue or white)
ψ ψ0.404 - 0.643mm
0.12 9 - 0.3 26mm 2
22 - 26AW G
7mm (0.27 ")
3mm Phillips
2.88 kgf-cm (2.5 lb-in)
-----
Scr ew ter minal
(FA N , NT C , DI M )± ± ±