Medela Harmony User manual

Harmony™
EN Fold this page out.
HU Hajtsa ki ezt az oldalt.
HR Rasklopite ovu stranicu.
CS Přeložte tuto stranu.
SK Stranu rozložte.
PL Rozłóż tę stronę.
EN Illustrated items or instruction steps are marked with the figure
and detail number (e.g. ¢2-01).
HU Az illusztrált elemeket vagy utasításlépéseket számok és az elem
száma jelöli (pl. ¢2-01).
HR Ilustrirane stavke ili koraci uputa označeni su brojem slike i detalja
(npr. ¢2-01).
CS Ilustrované položky nebo kroky instrukcí jsou označeny číslem
a číslem detailu (např. ¢2-01).
SK Ilustrované položky alebo kroky v návode sú označené číslom
obrázku a detailu (napr. ¢2-01).
PL Przedstawione na rysunkach elementy lub instrukcje są
oznaczone liczbą główną inumerem szczegółowym (np. ¢2-01).
POLSKI
73–85
PL
Laktator ręczny/
Zestaw Harmony
Essentials Pack
Instrukcja obsługi
SLOVENSKY
59–71
SK
Manuálna odsávačka/
Harmony Essentials Pack
Pokyny na používanie
ČESKY
45–57
CS
Manuální odsávačka mléka/
Harmony Essentials Pack
Návod k použití
HRVATSKI
31–43
HR
Ručna pumpa za izdajanje /
Harmony Essentials Pack
Upute za upotrebu
MAGYAR
17–29
HU
Manuális mellszívó/
Harmony Essentials Pack
Használati utasítás
ENGLISH
3–15
EN
Manual breast pump/
Harmony Essentials Pack
Instructions for use

4-01
√X
3-02
⌀
[mm]
…⌀17 …⌀20 …⌀23 …⌀26
24 30
21 27
6-03
6-04
6-06
6-09
6-10
6-08
6-07
6-11
6-13
6-12
S M L XL
7-01 7-02
6-01
3-01 3-03 3-04
2-01 2-02 2-03 2-04
5-01 5-02
6-02
6-05
6-14
5 min
4-02
3
3
¢4
¢2
¢1¢6
¢7
¢3
¢5

1. Important safety information
Please read all instructions before using this product.
Keep these instructions for future reference.
Warnings identify all instructions that are important for safety. Failure to observe these
instructions can lead to personal injury or damage to the product.
The following symbols and signal words show the significance of the warnings:
Can lead to serious injury or death.
WARNING
Can lead to minor injury.
CAUTION
Can lead to material damage
(not related to personal injury).
NOTICE
Useful or important information that is not
related to safety.
i Information
WARNING
To avoid health risks and reduce the risk of severe injury:
•Pumping can induce labour. Do not pump until after giving birth. If you become pregnant
while breastfeeding or breast pumping, consult with a licensed healthcare professional
before continuing.
•If infected with Hepatitis B, Hepatitis C, or Human Immunodeficiency Virus (HIV), pumping
breast milk will not reduce or remove the risk of transmitting the virus to your baby through
your breast milk.
•Wash all parts that come into contact with your breast and breast milk after every use.
•Small parts may be swallowed by toddlers. Close supervision is necessary when the breast
pump or accessories are used in the vicinity of children.
3

CAUTION
To avoid health risks and reduce the risk of injury:
•This is a single-user product. Use by more than one person may present a health risk.
•The device and its accessories are not heat-resistant. Keep away from heated surfaces or
open flames.
•Do not expose the device to direct sunlight.
•Before each use visually inspect the individual components for damage or wear. Never use
a defective device. Throw away parts at first signs of damage or weakness.
•Do not repair the device by yourself. Do not modify the device.
•Use the device only for its intended purpose as described in these instruction for use.
•Do not microwave or boil breast milk. Microwaving can cause severe burns to baby’s
mouth from hot spots that develop in the milk during microwaving (Microwaving can also
change the composition of breast milk).
•Clean and sanitise all parts that come into contact with your breast and breast milk prior to
first use.
•Only use Medela recommended parts with the device.
•While some discomfort may be felt when first using a breast pump, it should not cause
pain. If you are unsure about correct breast shield sizing please visit www.medela.com or
see a lactation consultant/breastfeeding specialist who can help you get a proper fit.
NOTICE
•Take appropriate care in handling bottles and components:
•Plastic bottles and parts become brittle when frozen and may break when dropped.
•Bottles and parts may become damaged if mishandled (e.g., dropped, over-tightened, or
knocked over).
•Do not use the breast milk from bottles or components that show signs of damage.
4

Contents
1. Important safety information 3
2. Intended purpose 6
3. Product description 6
3.1 Product variants 6
3.2 The Harmony breast pump includes 6
4. Getting started 6
5. Cleaning 7
5.1 Washing and sanitising the pump 7
6. Preparing for pumping 9
6.1 Selecting the correct breast shield size 9
6.2 Assembling the connector and breast shield 9
6.3 Assembling the handle 10
6.4 Placing the breast shield 10
7. Operating your breast pump 10
7.1 Mimicking the baby’s rhythm (2-Phase expression) 10
7.2 Expressing your breast milk 11
7.3 After pumping 11
8. Handling of breast milk 12
8.1 General storage guidelines 12
8.2 Freezing 12
8.3 Thawing 13
9. Troubleshooting 13
10. Accessories 14
11. Warranty 14
12. Disposal 14
13. Meaning of symbols 14
14. International regulations 15
14.1 Drinking equipment for children 15
15. Technical specifications 15
5

2. Intended purpose
The Harmony breast pump is a manual breast pump to be used by lactating women to
express and collect milk from their breasts. The Harmony breast pump is intended for a single
user.
3. Product description
The Harmony is a personal-use manual breast pump with a PersonalFit Flex breast shield and
an ergonomic 2-phase pump handle.
This enables you to alternate between short low-volume movements to stimulate the milk flow
and long, deep movements to optimally extract your milk – the way your baby does it.
The Harmony breast pump
•is easy to handle and clean.
•enables you to silently and discreetly extract your milk.
•includes a 24 mm PersonalFit Flex breast shield to give you more comfort and more milk.
3.1 Product variants
There are two different variants of the Harmony breast pump:
•Harmony breast pump: Includes the pump only.
•Harmony Essentials Pack: Includes the pump, a silicon teat compatible with the Harmony
bottle, four milk storage bags and four ultra-thin Safe & Dry nursing pads.
Please also read the instructions for use provided with these additional items.
3.2 The Harmony breast pump includes
Refer to figure ¢6 on the foldout pages.
¢6-01 (Disposable) protective cover
¢6-02 PersonalFit Flex breast shield 24 mm
¢6-03 Connector
¢6-04 Handle
¢6-05 Stem with O-ring
¢6-06 Diaphragm
¢6-07 Valve head
¢6-08 Valve membrane (2 pcs)
¢6-09 Bottle
¢6-10 Lid
¢6-11 Bottle stand
The following items are included in the
Harmony Essentials Pack only:
¢6-12 Feeding teat
¢6-13 Milk storage bag (4 pcs)
¢6-14 Safe & Dry nursing pad (4 pcs)
4. Getting started
To be ready for expressing milk for the first time, separate the parts of the breast pump, then
wash and sanitise them – see section 5.1.
6

5. Cleaning
5.1 Washing and sanitising the pump
Washing and sanitising are two different activities. They must be done separately to protect
you and your baby, and to maintain the performance of the device.
Wash – To clean the surfaces of the parts by physically removing contamination.
Sanitise – To kill microorganisms, such as fungi, bacteria or viruses, that may be present on
the surfaces of the parts.
CAUTION
•Separate and wash all parts that are exposed to breast milk immediately after use. This will
help to remove breast milk residue and prevent growth of bacteria.
•Wash hands thoroughly with soap and water.
•Only use drinking-quality tap water or bottled water for cleaning.
•Do not place pump parts directly in the sink to rinse or wash. Use a clean wash basin used
only for infant feeding items.
•Do not use a dish towel to rub or pat items dry.
•Do not use disinfectants for cleaning.
NOTICE
Pay attention to the following:
•Take care not to damage parts of the pump during cleaning. Do not use a sharp object
(such as a toothpick) for cleaning.
•Some parts of the Harmony breast pump are very small (e.g. the O-ring or the valve
membrane). Make sure that no parts are missing when you reassemble the pump after
cleaning.
•Store the dried pump parts in a clean bag/container until next use.
•Do not store wet or damp parts as mould may develop.
•If you notice a white residue on the parts after boiling, your water may have a high mineral
content. Remove residue by wiping parts with a clean towel and allow to air dry.
•Distilled water is recommended when boiling parts to prevent substantial mineral build-up
over time, which may compromise your parts.
i Information
If using the dishwasher, parts may become discoloured. This will not impact the part function.
What to do when: See detailed instructions on the next page.
7

Before first use, remove and dispose of the protective cover ( ¢6-01) from the breast shield.
Wash and sanitise the pump parts and bottles following the steps 1 to 4 below.
Wash your pump parts and bottles after each use and sanitise the parts once per day after
they have been washed.
1. Disassemble
Refer to figure ¢1 on the foldout page.
i. Disassemble the pump into its individual parts (breast shield, connector, handle, valve head and milk
bottle).
ii. Remove the diaphragm from the handle and pull the stem out.
iii.Remove the valve membrane from the valve head.
iv. Separate the milk bottle, lid and bottle stand.
2. Wash
Rinse and wash by hand Wash in dishwasher
or
i. Rinse the disassembled parts with cool
water (approx. 20°C).
ii. Clean these parts with plenty of warm,
soapy water (approx. 30°C). Use a commer-
cially available washing-up liquid.
iii.Rinse the parts with cool water for 10 to 15
seconds (approx. 20°C).
Place the disassembled parts on the top rack
or in the cutlery section. Use a commercially
available dishwashing detergent.
3. Sanitise (before first use and once per day)
Sanitise on stovetop Sanitise in microwave
5 min
or (except for
the handle)
Cover the disassembled, washed parts with
water and boil at least for 5minutes.
Use Quick Clean* bags in the microwave in
accordance with the instructions on the bags.
*Refer to local website/shops for availability in your country.
4. Dry
Allow to air-dry on a clean, unused dish towel or paper towel. Store the dry parts in a clean environment.
Do not store parts in an airtight container/bag if moist. It is important that all residual moisture dries.
8

6. Preparing for pumping
Only use clean and dry parts for assembly. Refer to chapter 5 for cleaning.
CAUTION
To prevent contamination of your milk:
•Wash hands thoroughly with soap and water before touching the pump parts and breasts.
•Dry your hands with a fresh towel or a single-use paper towel.
•Avoid touching the inside of bottles and lids.
To make sure that the device works properly and safely:
•Check pump components for wear or damage before use. Replace if necessary.
•Always inspect all parts prior to use for cleanliness. If dirty, clean according to chapter 5.
NOTICE
O-ring
Stem
The O-ring ensures a sealed connection between the handle and the
connector. This is necessary to build up a vacuum.
Make sure that the white O-ring is present in its groove of the stem.
If it is missing or defective, contact the Medela Customer Service.
6.1 Selecting the correct breast shield size
Refer to figure ¢7 on the foldout pages.
1. For proper sizing, measure the diameter of your nipple ( ¢7-01).
2. Select the breast shield that is slightly larger than your nipple ( ¢7-02).
For more information on breast shield sizing, visit www.medela.com.
6.2 Assembling the connector and breast shield
Refer to figure ¢2 on the foldout pages.
1. ¢2-01 Carefully push the breast shield into the top opening of the connector.
ÆChoose a breast shield size that suits your needs.
2. ¢2-02 Place the valve membrane in a horizontal position on the valve head. Carefully
push the knob on the membrane‘s back into the smallest hole of the head until it engages.
ÆThe membrane must lie flat on the head.
3. ¢2-03 Push the valve head onto the inner sleeve of the connector.
ÆThe valve head must be positioned sideways as shown in the picture.
4. ¢2-04 Screw the bottle into the connector.
9

6.3 Assembling the handle
Refer to figure ¢3 on the foldout pages.
1. ¢3-01 Insert the stem (with the O-ring) into the hole on the upper side of the diaphragm.
2. ¢3-02 Make sure that the oval shaped base of the stem is aligned correctly to the
diaphragm.
3. ¢3-03 Place the diaphragm into the pump handle. Mind the orientation (the recess in the
diaphragm engages on the tongue in the handle) and press down firmly around the entire
edge to ensure a proper seal.
4. ¢3-04 Insert the stem of the handle assembly in the opening on top of the connector.
Push until the stem locks into place.
6.4 Placing the breast shield
Refer to figure ¢4 on the foldout pages.
1. The oval breast shields can be rotated (360°) and placed in the desired position to have
the most comfortable fit for you.
2. ¢4-01 Place the breast shield on the breast so that the nipple is properly centred in the
tunnel.
3. ¢4-02 Hold the breast shield onto your breast with your thumb and index finger. Support
your breast with the palm of your hand.
4. Start pumping as described in section 7.2.
7. Operating your breast pump
7.1 Mimicking the baby’s rhythm (2-Phase expression)
Babies use a “two-speed” sucking action. At first, they suck quickly, and then they switch to a
slower, deeper sucking rhythm once milk starts to flow. The quicker sucking action stimulates
the milk ejection reflex and triggers the milk flow; the slower sucking draws the milk out for the
feeding phase.
2-Phase expression is a “two-speed” pumping action that mimics the baby’s natural sucking
rhythms. The pump’s handle design allows you to begin with fast sucking action called the
stimulation phase. For this, you actuate the short side of the handle with your thumb in a fast
manner. When you see milk flow or feel milk ejection, you can then switch to the expression
phase by actuating the longer side of the handle with your fingers in a slower, full stroke
manner.
10

7.2 Expressing your breast milk
CAUTION
•Do not hold the pump by the bottle.
This can lead to engorgement and blockage of the milk ducts.
•Only fill the bottle to the 150 ml mark.
•Contact your healthcare professional or breastfeeding specialist if you can express only
minimal or no milk or if expression is painful.
Refer to figure ¢5 on the foldout pages.
1. ¢5-01 Start pumping with stimulation: Using your thumb, press down the smaller part of
the handle. This is the part with the milk drops on top. Press and release quickly, again and
again, until your milk starts to flow.
2. ¢5-02 Once your milk starts to flow, switch to expression: With your fingers, press down
the lower, longer part of the handle.
By doing so, you build up a vacuum that facilitates the milk flow. You control the level of the
vacuum with the speed of the handle stroke and the compression that is created.
Decide yourself which pumping rhythm is the best for you.
3. Stop pumping when you feel that the milk does not flow anymore or when the bottle is full.
7.3 After pumping
Prepare the milk for storage as follows:
1. Unscrew the bottle from the connector.
2. Use the bottle stand to prevent the bottle from tipping over.
3. Close the bottle with a lid.
11

8. Handling of breast milk
8.1 General storage guidelines
Storage guidelines for freshly expressed breast milk (for healthy term babies)
Room temperature
16 to 25°C
(60 to 77°F)
Refrigerator
4°C (39°F)
or colder
Freezer
–18°C (0°F )
or colder
Breast milk thawed in
the refrigerator
Up to 4 hours is best
*Up to 6 hours for milk
expressed under very
clean conditions
Up to 3 days is best
*Up to 5 days for milk
expressed under very
clean conditions
Up to 6 months is best
*Up to 9 months for milk
expressed under very
clean conditions
At room temperature:
Up to 2hours
Refrigerator:
Up to 24 hours
Do not refreeze!
*Guidelines for expressing milk under very clean conditions:
Before expressing breast milk, mothers should wash their hands with soap and water or an
alcohol-based hand sanitiser. The pump parts, bottles and pumping area must be clean.
Breasts and nipples do not need to be washed before pumping.
•These guidelines for storage and thawing of breast milk are a recommendation. Contact
your lactation consultant or breastfeeding specialist for further information.
•Store breast milk in the coldest spot of the refrigerator (at the back of the glass shelf above
the vegetable compartment).
8.2 Freezing
NOTICE
•Repeated freeze/thaw cycles destroy the structure of the milk. Therefore, never refreeze
breast milk.
•Freeze expressed breast milk in plastic bottles or milk storage bags. Do not fill the bottles
or bags more than 3/4 full to allow space for possible expansion.
•Label the bottles or bags with the date and volume of expression.
•Plastic bottles and parts become brittle when frozen and may break when dropped.
•Do not use the breast milk from bottles or components that show signs of damage.
12

8.3 Thawing
CAUTION
Do not thaw or warm breast milk in a microwave or a pan of boiling water. This helps
preserve important components and prevents burns.
•To preserve breast milk components, thaw the milk overnight in the refrigerator.
•Alternatively, hold the bottle or bag under warm water (max.37°C / 98.6°F).
NOTICE
Gently swirl the bottle or bag to mix any fat that has separated. Avoid shaking or stirring the
milk.
9. Troubleshooting
In case of an unexpected behaviour of your breast pump check with the troubleshooting table if
you find the issue in the column “Problem” and follow the instructions in the column “Solution”.
Troubleshooting table
Problem Solution
There is low or
no suction Check the O-ring on the stem for presence and proper condition. If it is missing or defective, contact the Medela Customer Service.
Make sure that the breast shield forms a complete seal around the breast.
Make sure that the yellow valve head and the white membrane are clean and not
damaged.
Make sure that the membrane lies flat on the valve head.
Make sure that the valve head is positioned sideways on the connector.
Make sure that the components of the handle are assembled correctly.
Check all connections.
If suction does not improve after having followed these steps, contact the Medela
Customer Service.
There is no
milk flow Ensure your breast pump is assembled correctly and there is suction. Relax and take a 10-15 minute break if expression is not achieved after two consecutive
pumping sessions.
Consult your lactation consultant/breastfeeding specialist if expression still does not
occur.
If you have not resolved the problem with your breast pump or you have further questions, please contact
Medela Customer Service. For contact data visit www.medela.com. Under “Contact” choose your country.
13

10. Accessories
The following products are sold separately:
•PersonalFit Flex breast shield sizes S (21mm), M (24mm), L (27mm), XL (30mm)
•Breast milk bottle 150 ml, 250 ml
•Breast milk storage bags
Depending on your region, check local website/shops for availability.
11. Warranty
Please refer to the “International Warranty” for Medela products available under
www.medela.com to find out if and to what extent the warranty applies to this product.
12. Disposal
At the end of its operating life, separate the parts of your breast pump and dispose of
according to local regulations.
Breast shields, connector and accessories
The parts are made of plastics that are not harmful to the environment when disposed of as
household waste. Recycle or dispose of according to local regulations.
13. Meaning of symbols
Symbols used in these instructions
General safety alert symbol, points to
information related to safety. Read and follow the instructions for use.
14

Symbols found on the product parts and its packaging.
Identifies the manufacturer. Indicates the date of manufacturing.
Indicates the part number of the device. Indicates the lot/batch number.
Read and follow the instructions for use.
The packaging contains products
intended to come in contact with
food according to regulation EC
1935/2004.
Keep away from rain. Keep in dry
conditions. Indicates that the material is part of a recovery/recycling process.
Keep away from sunlight. Indicates that the package is made of
cardboard.
Contains fragile goods. Handle with
care.
14. International regulations
14.1 Drinking equipment for children
Teat and bottle intended for infant feeding comply with the European Standard EN 14350.
15. Technical specifications
Materials touching skin or coming in contact with milk
•Breast shield: Polypropylene, thermoplastic elastomer
•Connector, valve head: Polypropylene
•Diaphragm, valve membrane: Silicone rubber
•Bottle: Polypropylene
•Lid: Polypropylene
All parts that come in contact with breast milk are not made with BPA (Bisphenol A).
Enter “End of document” in a paragraph with the format Pagination
End of document
15

16

1. Fontos biztonsági információk
A termék használata előtt kérjük, olvasson el minden utasítást.
Őrizze meg a jelen használati útmutatót, mivel később még szüksége lehet rá.
A figyelmeztetések azokra az utasításokra hívják fel a figyelmet, amelyek biztonsági
szempontból fontosak. Az utasítások be nem tartása személyi sérüléshez vagy a termék
károsodásához vezethet.
Az alábbi szimbólumok és kifejezések a veszély súlyosságát jelzik:
Súlyos sérüléshez vagy halálhoz vezethet.
FIGYELMEZTETÉS!
Kisebb sérüléshez vezethet.
VIGYÁZAT!
Tárgyi sérüléshez vezethet
(személyi sérüléstől függetlenül).
ÉRTESÍTÉS
Hasznos vagy lényeges információ,
amely nem kapcsolatos a biztonsággal.
i Információ
FIGYELMEZTETÉS!
Az egészségi kockázatok és a súlyos sérülések csökkentése érdekében tartsa be az alábbiakat:
•A fejés beindíthatja a szülést. Csak szülés után kezdje el a fejést. Ha szoptatás vagy
mellszívó használata alatt esik teherbe, konzultáljon egy engedéllyel rendelkező
szoptatási tanácsadóval, mielőtt folytatná.
•Ha Ön Hepatitis B, Hepatitis C vagy humán immundeficiencia (HIV) vírussal fertőzött,
az anyatej lefejése nem csökkenti vagy szünteti meg a vírus anyatejen keresztül a babának
történő átadásának kockázatát.
•Használat után azonnal mossa meg a mellel vagy az anyatejjel érintkező alkatrészeket.
•A kis méretű alkatrészeket lenyelhetik a kisgyermekek. Felügyeletre van szükség,
ha a mellszívót vagy annak tartozékait gyermekek közelében használja.
17

VIGYÁZAT!
Az egészségi kockázatok elkerülése és a sérülések veszélyének csökkentése érdekében tartsa
be az alábbiakat:
•A terméket egy személy általi használatra tervezték. Több személy általi használata egészségi
kockázatot jelenthet.
•Az eszköz és annak tartozékai nem hóállók. Fűtött felületektől és nyílt lángtól távol tartandók.
•Ne tegye ki az eszközt közvetlen napfénynek.
•Minden használat előtt vizsgálja meg az egyes részegységeket, hogy látja-e rajtuk
sérülés vagy elhasználódás jeleit. Soha ne használjon sérült eszközt. Ha elhasználódás
vagy gyengülés jeleit tapasztalja, azonnal dobja ki az alkatrészeket.
•Ne kísérelje meg saját kezűleg megjavítani az eszközt. Ne módosítsa az eszközt.
•A terméket kizárólag a használati utasításban leírt rendeltetési célra használja.
•Ne melegítse az anyatejet mikrohullámú sütőben, és ne forralja fel azt. A mikrohullámú
sütő használata súlyos égési sérüléseket okozhat a baba száján, mivel a melegítés közben
forró pontok alakulhatnak ki a tejben (A mikrohullámú sütő emellett megváltoztathatja
az anyatej összetételét).
•Az első használat előtt minden olyan alkatrész tisztítását és fertőtlenítését végezze el,
amely érintkezésbe kerül a mellel vagy az anyatejjel.
•Az eszközt csak a Medela által ajánlott tartozékokkal használja.
•Bár a mellszívó első használata enyhe kellemetlenségérzettel járhat, nem szabad fájdalmat
éreznie. Ha továbbra sem biztos benne, hogy a megfelelő szívófejméretet választotta ki,
látogasson el a www.medela.com oldalra, vagy forduljon egy szoptatási tanácsadóhoz
vagy szakértőhöz, aki segíthet az ideális méret kiválasztásában.
ÉRTESÍTÉS
•A palackokat és az alkatrészeket kellő óvatossággal kezelje:
•A műanyag palackok és alkatrészek fagyasztáskor törékennyé válnak és leejtéskor eltörhetnek.
•A palackok és az alkatrészek megsérülhetnek a helytelen használat során (például leejtés,
túlfeszítés, vagy fellökés esetén).
•Ha a palackok vagy a részegységek sérülés jelét mutatják, ne használja fel az anyatejet.
18

Tartalomjegyzék
1. Fontos biztonsági információk 17
2. Rendeltetésszerű használat 20
3. A termék leírása 20
3.1 Termékváltozatok 20
3.2 A Harmony mellszívó a következőket foglalja magában: 20
4. Első lépések 20
5. Tisztítás 21
5.1 A mellszívó elmosása és fertőtlenítése 21
6. A szívás előkészítése 23
6.1 A megfelelő méretű szívófej kiválasztása 23
6.2 A könyökelem és a szívófej összeszerelése 23
6.3 A pumpakar összeszerelése 24
6.4 A szívófej elhelyezése 24
7. A mellszívó működtetése 24
7.1 A baba ritmusának utánzása (2-Phase expression) 24
7.2 Az anyatej lefejése 25
7.3 A szívás után 25
8. Az anyatej kezelése 26
8.1 Általános tárolási útmutatások 26
8.2 Fagyasztás 26
8.3 Kiolvasztás 27
9. Hibaelhárítás 27
10. Tartozékok 28
11. Jótállás 28
12. Ártalmatlanítás 28
13. A szimbólumok jelentése 28
14. Nemzetközi szabályozások 29
14.1 Gyermekek számára készült ivóeszközök 29
15. Műszaki információk 29
19

2. Rendeltetésszerű használat
A Harmony manuális mellszívó arra szolgál, hogy a szoptatós anyák lefejhessék vagy
összegyűjthessék az anyatejet az emlőjükből. A Harmony mellszívó kizárólag egy személy
általi használatra készült.
3. A termék leírása
A Harmony egy személyes használatra tervezett manuális mellszívó PersonalFit Flex szívófejjel
és egy ergonomikus 2-phase pumpakarral.
Ez lehetővé teszi a tejáramlás stimulálására szolgáló rövidebb, alacsonyabb mennyiséget
felszabadító mozdulatok, valamint a tej ideális lefejéséhez szükséges – a babáéhoz hasonló
– hosszabb, erőteljesebb mozdulatok váltogatását.
A Harmony mellszívó
•egyszerűen kezelhető és tiszta.
•lehetővé teszi, hogy csendesen és diszkréten fejje le a tejet.
•egy 24 mm-es PersonalFit Flex szívófej is tartozik hozzá, amely biztosítja a nagyobb kényelmet,
és több anyatej lefejését teszi lehetővé.
3.1 Termékváltozatok
A Harmony mellszívónak két különböző változata létezik:
•Harmony mellszívó: Csak a pumpa jár hozzá.
•Harmony Essentials Pack: Magában foglalja a mellszívót, a Harmony palackkal kompatibilis
etető cumit, négy tejtároló tasakot és négy extra vékony Safe & Dry szoptatóbetétet.
Kérjük, a kiegészítő elemekhez mellékelt használati útmutatót is olvassa el.
3.2 A Harmony mellszívó a következőket foglalja magában:
Tekintse meg a ¢6. ábrát a kihajtható oldalakon.
¢6-01 (Eldobható) védőborító
¢6-02 PersonalFit Flex mellszívófej (24 mm)
¢6-03 könyökelem
¢6-04 Kar
¢6-05 O-gyűrűvel ellátott szár
¢6-06 Membrán
¢6-07 Szelepfej
¢6-08 Szelepmembrán (2 db)
¢6-09 Palack
¢6-10 Fedél
¢6-11 Palackállvány
A következőket kizárólag a Harmony Essentials
Pack tartalmazza:
¢6-12 Etető cumi
¢6-13 Tejtároló tasak (4 db)
¢6-14 Safe & Dry szoptatóbetét (4 db)
4. Első lépések
Hogy felkészüljön a tej első alkalommal történő lefejésére, különítse el a mellszívó részegységeit,
majd mossa el és fertőtlenítse azokat – lásd: rész 5.1.
20