MediCrystal THERMOGEM BIO-MAGNETIC AMETHYST TOURMALINE JADE LONG... User manual

QUICKSTART GUIDE
All products, controllers, specications and data, and a set of items packaged in a box are subject to change without notice to improve the devices' reliability, function, or design.
Please, check for the details of the most updated products at the www.MediCrystal.com website.
EN
printed owner’s
guide
20
layers
H-60PVA
operational
CONTROLLER
with wires
1Layer 1 – High-quality heat resistant tan brown bicolor articial leather and eco-suede,
elegant, durable, comfortable, and easy to clean, featured with ThermoGem™ Logo on the
top.
2Layer 2 – Heat-resistant Mesh fabric with elegant embroidery to x Amethyst, Jade, and
Tourmaline by no glue artisan sewing process.
3Layer 3 – High Grade «A-AB» crushed to 2-10 mm and tumbled Natural, Not chemically
treated Purple Amethyst Crystals, Natural (non-ceramic) Black Tourmaline and Green
Jade Gems and Ceramic Tourmaline Hexagons. Hot crystals and gems release heating Far
InfraRed (FIR) rays and Negative Ions.*
Layer 4 – Bio-stimulation Photon Red Light LEDs. Visible red light at a wavelength of 660 nm.
5Layer 5 – Cotton layer with charcoal lamination for thermal preservation and even heat
distribution.
6Layer 6 – Non-woven anion fabric layer for increased release of Negative Ions upon heat
distortion.
7Layer 7 – Waterproof and thermal preservation complex aluminum lm to protect inner
vest sensors and heating systems from moisture and sweat.
8Layer 8 – Electronic-wave proof copper ber fabric EMI (Electro-Magnetic Interceptor)
layer for primary shielding user from any remaining electromagnetic elds (EMF).
9Layer 9 – Aluminum foil EMI layer blocking EMFs and uniformly distributing the heat to
the upper layer with gemstones.
10 Layer 10 – Durable 0.2 mm non-woven glass ber fabric layer for heating wire xing and
protection.
11 Layer 11 – Unique silicon heating wires in Teon insulation twice shielded with copper
and foil to eliminate EMFs.
Layer 12 – Thermostat sensors measure temperature in the dierent points of the
multilayer structure and report to the controller. You can see the current vest’s temperature
that on the controller display. The temperature sensors help to maintain consistent heat
levels throughout the vest as set by the user. They are also a part of the overheat protection
controller system.
Layer 13 – Bimetal switches for emergency overheat protection with automatic power
shut-o feature if the vest heats up to 80°C or 176°F.
14 Layer 14 – Cotton fabric laminated with red clay accumulating heat, discharging Negative
Ions, naturally releasing Far InfraRed rays.
15 Layer 15 – Charcoal fabric layer releasing Far InfraRed (FIR) Rays and Negative Ions,
decomposing and deodorizing smell.
16 Layer 16 – Pure aluminum foil FIR reection blocks heat from being conducted downwards
and assists other layers in distributing and continually releasing the heat evenly.
Layer 17 – VLF PEMF (Very Low-Frequency Pulsed Electromagnetic Fields) system coils.
18 Layer 18 – Non-woven fabric layer for heat absorption and preservation.
19 Layer 19 – Compressed non-woven cotton padding for thermal protection and increased
comfort.
20 Layer 20 – Waterproof polyester peach skin fabric for durability, tension resistance, and
protection from moisture, dirt, and wear.
CARRY AND STORAGE
BAG for your vest
EMF
FREE
HEATING
SYSTEM
11
THERMOGEM™ BIO-MAGNETIC AMETHYST TOURMALINE JADE LONG VEST
THERMOGEM™ VEST SET INCLUDES:
1
2
3
5
6
7
8
9
10
11
14
15
16
18
19
SIZE: 44"x44" (112x112 cm)
HEATING AREA: 43"x22" (110x55 cm)
FIR HEAT ADJUSTABLE: 86158°F 3070°C
1BIMETAL SENSOR
1 THERMOSTAT SENSOR
24 RED LIGHT LEDS
3 PEMF COILS
5 lbs (2,3 kg) OF CRUSHED AMETHYST CRYSTALS
2.2 lbs (1 kg) OF CRUSHED TOURMALINE GEMS
2.2 lbs (1 kg) OF GREEN JADE STONES
70 pcs CERAMIC TOURMALINE HEXAGONS
HEATING POWER: 180W
TOTAL WEIGHT: 16 lbs (7 kg)
20
long Vest
Vest electrical connector
for controller plug.
A tight connection
between the vest and
controller is essential to
avoid errors and faults
44" (112 cm)
44" (112 cm)
The vest closures provide
a comfortable t for men
and women of all ages
Monochromic 660 nm
Red Light LEDs
Natural
Amethyst
Natural Black
Tourmaline
Green Jade
Ceramic
Tourmaline
Tumbled Natural Amethyst, Tourmaline, Jade crystals, and
1/4 inch thick ceramic Tourmaline hexagons are xed
without glue by special heat-resistant mesh fabric
43" (110 cm)
22" (55 cm)
heating area
!VOLTAGE: 220�240V UK, EU

QUICKSTART GUIDE
All products, controllers, specications and data, and a set of items packaged in a box are subject to change without notice to improve the devices' reliability, function, or design.
Please, check for the details of the most updated products at the www.MediCrystal.com website.
*ThermoGem™ stone mattresses, mats, pads, belts, wraps, pillows can
help you create a relaxing, soothing, and re-energizing environment to
maintain your wellness, balance, sound sleeping, physical strength, and
tness and awaken the restfulness, comfort, and invigoration powers
and energies. Together with exercises and a healthy diet, ThermoGem™
products may supplement your daily activity and become an essential
part of your healthy lifestyle, improving your ability to do everyday
things and enhance your life experience. ThermoGem™ products are
not intended to diagnose, cure, treat, mitigate, or prevent any disease,
illness, or medical condition or substitute medical treatment of any kind
or aect the body's structure or function. Information here is never to be
construed as medical advice. It does not reect or represent a product
claim. FDA has not approved or evaluated ThermoGem™ products or this
information. All products, specications, and data are subject to change
without notice to improve the products' reliability, function, or design.
LEGAL DISCLAIMER
1
3
5
2
4
6
8
9
7
10
11
12 13
14
MediCrystal® and ThermoGem™
products for the Asian region, EU, and
the UK are ready for 220-240V power
outlets. EU product comes with CEE
7/3, CEE 7/5, or a universal earthed
CEE 7/7 plug and a permanently tted
UK safety-approved conversion plug.
You can use a high-quality adapter
if your country’s outlet has the same
voltage but a dierent conguration.
Please make sure your product’s voltage is the same as your country’s
power grid. If your mat is rated for the North American 110-120V voltage
and the controller comes with a standard US NEMA 5-15P plug, use it
only in North America or Japan. If you are going to 220-240V countries,
do not use travel adapters. Use your product only with a step-down
220-250V to 110V voltage converter. The converter wattage should be
at least three times higher than the mat’s power consumption. Do not
connect the 110-120V mat into the 220-250V outlet through an adapter
and vice-versa. If you plug in a device to the wrong voltage outlet, the
product may be severely damaged and cause re risks!
1
Power ON/OFF Toggle Button – Push it to turn the vest ON/OFF. When you turn it ON, the display  will show ON. It means that the
controller is ON and ready to choose the program. If the controller display shows --, the Power is connected, but the Button has not
been activated, and no functions can be operated. Press the power button again with some eort so that display   shows ON.
2POWER indicator – Lights up when Power is ON.
3
Timer Control Toggle Button – Select one of the 4 options shown on the display : 1H, 4H, 8H, 0H for 1, 4, 8, 12 hours heating
session with auto shut-o when the time expires, or you can choose -H (NO HEATING MODE) for only PEMF function without heating.
Press and hold for 5 seconds to turn OFF Auto-Protection Feature; the display will show S-. Press and hold again to
reactivate this feature, and the display will show SA.
4«HEATING» Operation Indicator – ON when the vest is heating, OFF when the set temperature is reached.
5
Temperature, Timer, Frequency, and Program Display – Switches into Temperature Mode when the Temperature Dial  is rotated.
The display shows the current Celsius temperature (30–70°C), ashes to the set temperature when the dial is rotated, then back again.
If the temperature is more then 122°F (50°C) for longer than 3.5 hours, Auto-Protection Feature will decrease it to a safe
113°F (45°C) level, and the display will show [ ].
In Timer mode, the display shows one of the 5 heatings time settings 1H, 4H, 8H, 0H, or -H chosen by the Timer Control Button
. When the heating program is over, the display will show --, OF, or ON, indicating that Power is ON, but the time set has
expired. Add time to resume heating or push the Power Button  to turn o the controller.
In PEMF Program mode, the display shows one of the PEMF program settings. P- (PEMF OFF for FAR INFRARED heating function
only), PO (manual frequency adjust mode), P1, P2, P3, P4, P5, P6, P7, P8, P9, PA, PC, PE, PF (automatic PEMF programs).
Please, check the controller user guide for details. If Manual Frequency adjusts dial  is in active mode display shows current
PEMF frequency in Hz (1–30 number of pulsations per second). Please, check the controller user guide for details.
In PHOTON Program mode, the display shows one of three PHOTON program settings. 1P = PHOTON ON 30 minutes. 2P = PHOTON runs 8
program cycle (One cycle = PHOTON ON 30 minutes OFF 30 minutes). -P (PHOTON OFF for FAR INFRARED and/or PEMF functions only).
The display may also show OF, ickering or static -- if the Power Button  is not pressed or the connection between the controller and
the vest is lost. Press Power Button  to turn ON all other controller functions or reconnect the controller to the vest tightly to resume.
6Adjust Temperature Dial – Use to increase or decrease heat 30–70°C (86–158°F). The dial range is marked, indicating the
desired temperature in °F.
7PEMF Program Button – Choose P- (PEMF o) one of 13 automatic Program options P1, P2, P3, P4, P5, P6, P7, P8, P9, PA,
PC, PE, PF shown on display  or switch to manual frequency adjust mode PO. Press and hold for 3 seconds to quickly return to
P- (PEMF o). Please, check the controller user guide for details.
8Adjust PEMF Frequency Dial – Use to increase or decrease magnetic pulsation frequency from 1 to 30 times per second. You
can try dierent frequencies to nd what works better for you.
9Adjust PEMF Frequency Dial ON Indicator – Lights up when PEMF manual adjust dial is ON, frequency is chosen in manual
mode, PEMF is ON, OFF when it stops.
10
PEMF ON Indicator – Lights up when PEMF function is ON, OFF when it stops.
11 PEMF PROGRAM CYCLE Indicator – Lights up when PEMF is auto cycled by the program, OFF when the whole program is over.
12
PHOTON Program Button – Choose one of three PHOTON program settings. 1P turns ON Red Light LEDs for 30 minutes. 2P runs an eight
cycles program (One cycle = PHOTON ON 30 minutes, OFF 30 minutes). -P (PHOTON OFF for FAR INFRARED and/or PEMF functions only).
13 PHOTON ON Indicator – Lights up when the Red Light LEDs are ON, OFF when PHOTON function stops.
14
PHOTON PROGRAM CYCLE Indicator – Lights up when Red Light is auto cycled by the program, OFF when the whole Program is over.
CONTROLLER H-60PVA for vests with PEMF and PHOTON
1. Consult your health professional to make sure that you can use red light, hot stones, FIR
sauna, and PEMF (pulsed electromagnetic elds). Take extra care if you have any health
issues.
2. Read the USER GUIDE, safety instructions, «use with caution», and contraindication
sections to be sure that the vest is OK for you, especially if you will use it use it on high
heat settings or sleep with it.
3. Drink a lot of water, juices, herbal teas before, during, and aer sessions, and replenish
minerals such as calcium, potassium, sodium, magnesium, and others lost with sweat or
urine.
4. Create a relaxing surrounding atmosphere.
5. Put the vest on your bed or the oor with crystals facing up.
6. If you have a regular connector, please connect the controller to the vest to t snugly. If
your device comes with an in-line connector, connect it so that the male plugs go inside
the female pins. Then screw the connector so that it’s tight.
7. Turn the controller ON and set the timer, only then set the max temperature to test the
vest for an hour. While it is cooling down, test PEMF functions for 15-20 minutes. Do
not put the protector on the vest or lay on it during this time.
8. Cover the vest ENTIRELY with a blanket to pre-heat the stones for 30-60 minutes to
set level. If the vest is covered only PARTIALLY, it may cause dierent temperatures in
dierent parts of the vest, sensors disruption, and controller malfunction.
9. The vest is rather exible, but it is essential not to apply excessive pressure to the
amethyst pad; never stand on the vest or bend it too much.
10. If the vest is too hard for you, or you sweat a lot and get wet, put on your T-shirt or pajama
under the vest. It will also cushion it and eliminate the crystals’ pressure. You may use a
towel instead if necessary. For more Red Light, try a plain vest for 15-30 minutes.
11. Start with the vest on the lowest heat settings, 35-40°C or 96-112°F, and short
sessions only for 15-20 minutes (do not forget to pre-heat the vest, it will be slightly
warm); watch how your body reacts.
12. If you enjoy shorter sessions and your body reacts well, move up to longer or more
intensive and frequent sessions.
13. Gradually increase the temperature by several degrees and session time by 5 minutes
each other day, and only if you feel comfortable and want a more intensive experience.
14. You should choose the length, intensity, and frequency of the sessions to feel comfortable
and refreshed. If your mat is equipped with an adjustable frequency controller, it is
suggested to start PEMF at a low frequency such as 4 Hz then increase to 8, 10, or 14 Hz.
Usually, lower frequencies have more calming eects, while higher frequencies provide
more stimulation and promote activity.
15. You should also have some rest between the sessions and never start with more than
three a week before you are better informed about how they inuence you.
16. You can also try the PEMF function, on the lowest heating levels, for 20-30 minutes to
check how your body reacts. Later if necessary, you will be able to use all the functions
or any of their combinations together. However, we recommend not using PEMF on high
heat to avoid overstimulating.
17. You should not feel any discomfort — but if there is any, rest several days and restart
with the temperature, length, and frequency set to the lowest possible.
18. Unplug your controller from the wall socket always when not in use. But do not
disconnect the controller from the vest more frequently than necessary to avoid the
connection becoming loose.
Regular connector
for controller plug
In-line screw connector
between the vest and controller
OR
QUICK START GUIDE
THERMOGEM™ BIO-MAGNETIC AMETHYST TOURMALINE JADE LONG VEST