MEI Conlux CV1000 User manual

CV1000
BILL VALIDATOR
Status LED
A Status LED assists in diagnosing the condition of
the Series CV1000. The following is a description
of the LED codes, their meanings, and suggested
remedial actions.
Signal Meaning Solution
LED ON Indicates the unit is enabled and
ready to accept a bill. No action necessary.
LED OFF Indicates that no power has
been applied to the unit.
Check to ensure that power is applied.
1 Flash Indicates that something is
obstructing the bill path. Remove the magazine and LED housing;
inspect for foreign material
2 Flashes Indicates the unit is not enabled. Verify conguration.
Check the coin tube levels in the coin
changer. There must be coins in each tube.
Note: Many machines disable the bill
Validator if the machine door is open and
the door switch is not activated or if the
machine is out of product.
3 Flashes Indicates that the bill path
needs cleaning for optimum
performance.
Remove the magazine and LED housing
and follow cleaning instructions to clean
the bill path.
4 Flashes Indicates that something is
obstructing the cross channel
sensor.
Remove the LED housing and look at the
bill path on the housing and inside the unit
for foreign material; clean as necessary.
5 Flashes Indicates that the magazine is
removed (the unit will not accept
bills without the magazine
attached).
Reinstall the magazine.
Slow
Flashes Unit is defective. Replace the unit.
Fast
Flashes The magazine is full of money. Remove money from the magazine.
Status LED
Conguration
Button
© MEI 2012 P/N 252657005
MEI
Suite 200, 3222 Phoenixville Pike
Malvern, Pa. 19355
Technical Support:
1-800-345-8172
www.meigroup.com
The CONLUX series CV1000 Bill Validator will
accept the Conlux Free vend, Conlux Value
vend, Conlux low cost Free vend coupons, the
Pepsi coupon, and the Aramark $1.00 coupons.

Installation
The Series CV1000 has been designed for
ease of mounting onto existing studs provided
by Original Equipment Manufacturers (OEMs).
Some machines may require brackets or
faceplates to mount the unit. Refer to your
machine operation manual or contact your
distributor/OEM for more model-specic
mounting information.
1. Disconnect all power to the machine.
2. Secure the unit to the mounting studs
with the appropriate hardware.
3. Connect the interface harnesses from the
machine to the unit.
4 - 11/32 nuts
4. Apply power to the machine.
5. Check the Status LED for the “Steady
ON” condition. If the LED is ashing,
refer to the Status LED Chart.
6. Insert a bill to check acceptance. If
enabled, the bill will be accepted.
7. Make a vend to ensure credit is received
and proper change is paid out for the
bill.
The Series CV1000 is precongured during
manufacture to accept U.S. 1.00’s. The
Series CV1000 can be manually congured
using an option coupon or by inserting a bill
of the desired denomination . If the Series
CV1000 is reprogrammed using a coupon
with a different conguration, the new
conguration will be the default. The coupon
conguration will remain in memory even with
the power off.
COUPON CONFIGURATION
PROCEDURE
1) Carefully copy the coupon from the Installation
Guide. Make copies of the coupon with a
standard, carbon-based, non-color copier.
The copies of the coupon must be the size of a
U.S. $1 dollar bill.
2) Use a #2 pencil to ll in the blocks for desired
options.
For correct operation, all 3 sections must be
completed. Fill in only one block per line. Do
not mark anywhere else or on the back of the
coupon.
Complete section 1 to enable desired
bill denominations. Enable 1 or 2 direction
face up, or 4 way acceptance (which allows
acceptance in all directions).
Complete section 2 to enable desired
bill denominations. Fill in one block for
each denomination. Be sure to mark all the
denominations.
Off will reject bills of the selected denomination.
ACCEPT will accept bills of the selected
denomination.
Section 3 - Not Applicable
Section 4 - Not Applicable
Complete section 5 to control the Bezel
Lights.Flashing or constantly ON may
be selected.
3) Locate the blue conguration button on the
back of the unit. Depress the button once to
enter programming mode. The red LED Status
light will ash rapidly. Depressing the button
again will exit the mode.
4) Insert the coupon face up and verify the
settings were accepted.
ACCEPTED: Coupon returned imediately and
the LED and the green arrows on the front of
the bill validator ash 10 times when coupon is
pulled out.
REJECTED: Coupon returned after ten
seconds. The red LED and the green arrows on
the front of the bill validator ash the number of
times corresponding to the section improperly
lled out. Example: two ashes for improper
section two.
Bill Conguration
An alternative to using the programming coupon
is to program a CV1000 with a particular
denomination of currency:
Press the Blue conguration Button on the back
of the CV1000 Validator. The red LED status
light, next to the blue conguration button, will
switch from steady ON to RAPIDLY FLASHING.
Insert a bill of the denomination you wish to
enable or disable. The bill will be returned to you.
If it is enabled, the red LED status light and the
green arrows on the front of the bill validator will
ash 10 times.
If the bill is already enabled, it will be disabled, it
will be returned to you, and the red LED status
light and the green arrows will ash 3times.
Repeat the process to return to the former setting.
7Flashes means the programming was not
accepted.
IMPORTANT!!
DO NOT leave the machine until the
Status LED returns to steady ON.