ICT Bill Validator S7 Series User manual

4 - Way Acceptance
Low Maintenance
Easy Installation
Re - Programmable
Flash ROM
Auto Self -Adjusting
Sensor System
Saving Power
B V or
ill alidat B V or
ill alidat
S7 Series
Installation Guide
2003 International Currency Technologies Corporation
Vol. 6.0 Part Number : H4524E-R

S7 Bill Validator Specifications ........................................ 2
The Front LED ................... ............................................. 4
The Back LED Status ...................................................... 4
S7 Pin-out Assignments (M.D.B. System for 12V DC) ............. 5
S7 Pin-out Assignments (Service Pulse for 12V DC) ..................... 6
S7 Wake_ up Signal ......................................................... 7
S7 Service Signal ............................................................. 7
Cable ............................................................................... 8
WEL-V705
WEL-S702
Switch Settings ....................................................(Appendix)
ContentsContents

S7 Bill Validator Specifications
Acceptance Rate
Bill insertion
Acceptance Speed
Interfaces
Bill box Capacity
96% or greater
4-way Acceptance
Approx. 3 seconds (including bill stacking)
M.D.B. (Multi-Drop Bus)
Pulse
Approx. 200 bills (200~300)
400 bills (300~500)
800 bills (750~850)
- 2 -
Power Sources
Weight
Environment Range
12V DC ± 10% (9V ~15V DC)
Power Consumption
Approx. 2kg (shipping)
Operating Temperature : -10 C~50 C
Storage Temperature : -30 C~70 C
Humidity : 30%~85% RH (no condensation)
Action mode 12V , 2A (peak), 650mA (average)
Standby mode 9V~15V DC
Power saving mode 12V , approx. 40 A
( ) We recommend the input has to be 12V DC.
If the input is lower than 9V DC, the machine may be shut down.
If the input is higher than 15V DC, the machine may be break down.
- 3 -
S7
Unit : :mm
( ) : in
51.0(2.008")
95.0(3.740")
69.5(2.736")
4.0(0.157")
134.0(5.276")
7.5(0.295")
126.5(4.980")
78.5(3.091")
78.5(3.091")
6-R2.65(R0.104") 232.0(9.134")
19.5(0.768")
10.0(0.394")
400 pcs.
800 pcs.
200 pcs.
100 pcs.
9.0(0.354") 23.5(0.925")
59.0(2.323") 52.0(2.047")
179.5(7.067") 200 bills 161.5(6.358") 100 bills 194.5(7.657") 400 bills
254.5(10.020") 800 bills
94.0(3.70")
83.0(3.27")
116.0(4.57")8.0(0.31") 115.0(4.53")
50.8(2.00")
239.0(9.41")
132.0(5.20")
13.0(0.51")
48.6(1.31")
107.0(4.21")
115.0(4.53") 200bills
97.0(3.82") 100bills
200 pcs.
100 pcs.
130.0(5.12") 400bills
400 pcs.
190.0(7.48") 800bills
800 pcs.

- 4 -
DIAGNOSTICS (GREEN LED)
LED LED OFF=POWER OFFON=OK
FLASHES STATUS
1 bill jammed
2 disabled from system
3 sensor problem
4 reserved
5 bill box is removed
6 bill box is full of money
The two LED lights located at the front of the unit will show the operational
status of the bill validator. The LED lights will flash ON and OFF (in 500ms
intervals) when the unit is ready to accept bills. The LED lights will be OFF
if the unit is disabled, out of service or in power saving mode.
The bill validator can only accept one bill at a time. The LED lights will be
OFF and will not accept another bill while a bill is being validated in the unit.
The LED lights will start to flash normally when the bill validator is ready to
accept the next bill. In power saving mode, although the LEDs are off, the
bill validator in still ready for accepting a bill.
The Front LED
The Back LED Status
Figure 1
Note:
In addition to the 30-pin connector, there is also an 8-pin RJ-45 connector on
the side of the bill validator designed for the purpose of downloading programs
and updating validation software. The connector will be kept open under
normal operation of the bill validator. It will only be used when a new software
or programs need to be downloaded into the flash ROM. The pin-out
assignments of the 8-pin RJ-45 connector are as follows:
Pin 1 - GND Pin 5 - /RESET
Pin 2 - TXD2 Pin 6 - VCC
Pin 3 - RXD2 Pin 7 - RXD1
Pin 4 - PROGRAM Pin 8 - TXD1
Option Switches Back LED
- 5 -
For the MDB interface S7 bill validator, connect the 30-pin peripheral connector
on one end of the harness to the side of the unit and the standard 6-pin MDB
connector to the power/interface connector.
The standard 6-pin MDB connector pin-out assignments:
Pin 1 - +12 VDC (POWER IN)
Pin 2 - GND (POWER RETURN)
Pin 3 - WAKE_UP
Pin 4 - MASTER RECEIVE (MDB_MASTER_RxD)
Pin 5 - MASTER TRANSMIT (MDB_MASTER_TxD)
Pin 6 - COMMUNICATIONS COMMON (MDB_GND)
Dual-in-line 30-pin peripheral connector (S7, MDB) pin-out assignments:
S7 Pin-out Assignments (M.D.B. System for 12V DC)
1 2 3 4 5 6 7 8 9 10
2519
11
2620
12
2721
13
282216
14
292317
15
302418
456
3
2
1
CAUTION: Turn off the power before connecting or disconnecting the
bill validator.
Pin 16 - Reserved
Pin 17 - WAKE_UP
Pin 18 - Reserved
Pin 19 - Reserved
Pin 20 - GND
Pin 21 - Reserved
Pin 22 - Reserved
Pin 23 - Reserved
Pin 24 - Reserved
Pin 25 - Reserved
Pin 26 - Reserved
Pin 27 - Reserved
Pin 28 - MDB_GND
Pin 29 - Reserved
Pin 30 - Reserved
Pin 1 - Reserved
Pin 2 - Reserved.
Pin 3 - +12 VDC
Pin 4 - Reserved
Pin 5 - Reserved
Pin 6 - MDB_MASTER_RxD
Pin 7 - Reserved
Pin 8 - Reserved
Pin 9 - Reserved
Pin 10 - Reserved
Pin 11 - Reserved
Pin 12 - Reserved
Pin 13 - Reserved
Pin 14 - MDB_MASTER_TxD
Pin 15 - Reserved
Cable Order No. : WEL-V705(3-BA-A7V7-51)
*

- 6 -
S7 Pin-out Assignments (Service Pulse for 12V DC)
1 2 3 4 5 6 7 8 9 10
2519
11
2620
12
2721
13
282216
14
292317
15
302418
For the 12V DC version of the S7 bill validator, the harness(WEL-S702) has
a dual-in-line 30-pin peripheral connector at one end and a 9-pin mating
connector at the other end.
9-pin mating connector pin-out assignments:
Pin 1 INHIBIT + Pin 6 Reserved
Pin 2 INHIBIT - Pin 7 CREDIT+
Pin 3 SERVICE + Pin 8 Reserved
Pin 4 Reserved Pin 9 CREDIT- & GND
(Power Return )
Pin 5 +12V DC
(Power In)
Dual-in-line 30-pin peripheral connector pin-out assignments:
Cable Order No. : WEL-S702
123
65
4
78 9
CAUTION: Turn off the power before connecting or disconnecting the
bill validator.
Pin 16 - Reserved
Pin 17 - Reserved
Pin 18 - INHIBIT -
Pin 19 - Reserved
Pin 20 - GND (Power Return)
Pin 21 - KEY
Pin 22 - SERVICE+
Pin 23 - Reserved
Pin 24 - Reserved
Pin 25 - Reserved
Pin 26 - Reserved
Pin 27 - Reserved
Pin 28 - Reserved
Pin 29 - Reserved
Pin 30 - Reserved
Pin 1 - CREDIT-
Pin 2 - CREDIT+
Pin 3 - +12V DC(Power In)
Pin 4 - INHIBIT +
Pin 5 - KEY
Pin 6 - Reserved
Pin 7 - Reserved
Pin 8 - Reserved
Pin 9 - Reserved
Pin 10 - Reserved
Pin 11 - Reserved
Pin 12 - Reserved
Pin 13 - Reserved
Pin 14 - Reserved
Pin 15 - Reserved
*
- 7 -
1. Mode 1 & Mode 1+2 :
When S7 takes the bill, it sends a signal through 〝Wake_up〞pin as
below:
2. Mode 2 & Mode 1+2 :
When S7 is in the modes, S7 can be woken up throughWake_uppin
by the following signal :
S7 Wake_up Signal
Normal
Normal
Wake up
Wake up
DC 0~1 V
DC 0~1 V
DC+ 5~12 V
DC+ 5~12 V
100 ms
10~100 ms
1. Condition 1 : When B.A. wakes up and does not take any bill.
2. Condition 2 : When B.A. takes a true bill.
3. Condition 3 : When B.A. rejects a fake note.
S7 Service Signal
Close
Close
Close
Sleep
Sleep
Sleep
Stacking
Reject the bill
Wake up
Wake up
Wake up
Bill input
Bill input
giving credit Idle few secs
Open
Open
Open

- 8 -
Cable
(MDB for 12V DC)
- 9 -
DC 12V
#WEL-S702
++
++
+ + +
+ +
AMP 172340-1 BACK VIEW
+AMP
3 2 1
9 8 7
1 2 3 4 5 6 7 8 9
1
16
2
17
3
18
4
19
5
20
6
21
7
22
8
23
9
24 10 25
11
26 12 27 13 28 14 29 15 30
PIN 1 CREDIT+ BROWN
PIN 2 CREDIT- PURPLE
PIN 3 +12VDC RED
PIN 4 INHIBIT+ BLUE
PIN18 INHIBIT- GREEN
PIN20 GED WHITE
PIN22 SERVICE+ YELLOW
PIN 1 INHIBIT+.......................................BULE
PIN 2 INIHBIT-.....................................GREEN
PIN 3 SERVICE.................................YELLOW
PIN 4 Reserved
PIN 5 +12V DC.........................................RED
PIN 6 Reserved
PIN 7 CREDIT+..................................PURPLE
PIN 8 Reserved
PIN 9 CREDIT- & GND.......WHITE & BROWN
WEL-S702WEL-S702
AMP 172340-1
BLK-15*2
* *
2464 22 AWG 7C CABLE