Meinberg IMS-HPS-100 User manual

MANUAL
IMS-HPS-100 Setup Guide
Hot-Plug Module
14th November 2019
Meinberg Funkuhren GmbH & Co. KG

Table of Contents
1 Imprint 1
2 Safety Instructions for hot pluggable Modules 2
2.1 Additional Safety Hints ........................................... 3
2.2 Supply Voltage ................................................ 3
2.3 Cabling ..................................................... 4
3 Replacement or Installation of a Hot-pluggable IMS Module 5
4 HPS-100: PTP / SyncE / Hardware NTP Interface 6
4.1 HPS100 - Global Configuration ...................................... 8
4.2 Option: Output Configuration ........................................ 9
4.3 Firmware Update via Web Interface .................................... 10
Date: 14th November 2019 IMS-HPS-100 Setup Guide

1 Imprint
1 Imprint
Meinberg Funkuhren GmbH & Co. KG
Lange Wand 9, 31812 Bad Pyrmont / Germany
Phone: + 49 (0) 52 81 / 93 09 - 0
Fax: + 49 (0) 52 81 / 93 09 - 230
Internet: https://www.meinbergglobal.com
Mail: [email protected]
Date: 2016-05-03
IMS-HPS-100 Setup Guide Date: 14th November 2019 1

2 Safety Instructions for hot pluggable Modules
Check before every maintenance work on the system:
•If a data backup is required?
•Is a backup required, verify the data recovery which is done by this backup.
•Make sure to avoid any static discharge while working - use a grounding cable and/or antistatic gloves
during installation and removal of hot pluggable components.
•If you are replacing a hot pluggable power supply, unplug the power cable prior to removing the module
from the case.
•Never open a power supply. In power supplies dangerous voltages can still remain even after disconnection
from the power supply. Always send power supplies back to the manufacturer for maintenance.
Exchange of hot-swap components
•Ensure that components which will be replaced during operation, always be treated with the utmost care.
Avoid contact with live components.
•Electrostatic discharge can damage electronic components. For this reason, ensure protection against
electrostatic discharges by wearing anti-static shoes while working with the system.
•Take care when removing and installing the hot-plug modules. Always work with the utmost caution.
Touch the modules only at the edges.
•Place the module out of the box or after removal from the system with the component side to the top on
a grounded and static-free surface.
•Storage of an IMS module must be done in a dry place.
•Installation or removal from hot-swap components only by authorized personnel!
2 Date: 14th November 2019 IMS-HPS-100 Setup Guide

2 Safety Instructions for hot pluggable Modules
2.1 Additional Safety Hints
This manual contains important information for the installation and operation of this device as well as for your
safety. Make sure to read carefully before installing and commissioning the device.
Certain operating conditions may require the observance of additional safety regulations not covered by this
manual. Nonobservance of this manual will lead to a significant abatement of the security provided by this
device. Security of the facility where this product is integrated lies in the responsibility of the installer.
The device must be used only for purpose named in this manual, any other use especially opteration above the
limits specified in this document is considered as improper use.
Keep all documents provided with the device for later reference.
This manual is exclusively for qualified electricians or by a qualified electrician trained personnel who are
familiar with the applicable national standards and specifications, in particular for the construction of high
voltage devices.
2.2 Supply Voltage
WARNING!
This device is powered by a dangerous voltage. Nonobservance of the safety instructions of this manual may
lead to serious damage to persons and property and to danger to life! Installtion, commissioning, maintenance
and operation of this device are to be carried out by qualified personnel only.
The general safety instructions and standards ( e.g. IEC, DIN, VDE, EN ) for installation and work with
high voltage equipment as well as the respective national standards and laws must be observed.
NONOBSERVANCE MAY LEAD TO SERIOUS DAMAGE TO PERSONS AND PROPERTY AND TO DAN-
GER TO LIFE!
The device may not be opened. Repair services may only be carried out by the manufaturer.
Supply lines for this decice must be equipped via an appropriate switch that must be mounted close to the
device and must be marked as a mains switch for the device.
To ensure safe operation supply mains connected to this decice must be equipped with a fuse and a fault-
current circuit breaker according to the applicable national standards for safe operation.
The device must be connected to a protective earth with low grounding resistance according to the applicable
national rules.
IMS-HPS-100 Setup Guide Date: 14th November 2019 3

2.3 Cabling
WARNING!
DANGER TO LIFE BY ELECTRICAL SHOCK! NO LIVE WORKING!
Wiring or any other work done the connectors particularly when connectors are opened may never be carried out
when the installation is energized. All connectors must be covered to prevent from accidental contact to life parts.
ALWAYS ENSURE A PROPER INSTALLATION!
4 Date: 14th November 2019 IMS-HPS-100 Setup Guide

3 Replacement or Installation of a Hot-pluggable IMS Module
3 Replacement or Installation of a Hot-pluggable
IMS Module
If the system is supplied with an antenna and antenna cable, it is advisable to first mount the antenna in a
suitable location (see chapter Antenna Mounting) and lay the antenna cable.
Please use a Torx screwdriver (T8 x 60) for removal and installation of the module.
1. Follow the safety instructions at the beginning
of this manual!
1. Remove the two marked Torx screws from the
module holder plate or the cover plate of
the empty slot.
2. (Only for an already built-in module)
Pull the module carefully out of the holding
rail. Note that the module is firmly anchored
in the connector block of the housing. You need
a certain amount of force to release the module
from this link. Once the connection to the
connector block of the system’s backplane is
loosened, the module can be easily pulled out.
3. When installing the new IMS module, please ensure that the board is correctly inserted into the
two guide rails of the system housing. Non-observance can cause damage to the module and the chassis.
Make sure that the module is securely locked into the connector block before you fasten the two screws.
4. Now you can put the installed module into operation.
Attachment points of an 1U IMS system
IMS-HPS-100 Setup Guide Date: 14th November 2019 5

4 HPS-100: PTP / SyncE / Hardware NTP
Interface
IEEE 1588 v2 compatible
Profiles: IEEE 1588v2 Default Profile
IEEE 1588v1 (option)
Enterprise Profile
IEC 61850-9-3 Power Profile
IEEE C.37.238-2011 Power Profile
IEEE C.37.238-2017 Power Profile
ITU-T G.8265.1 Telecom Frequency Profile
ITU-T G.8275.1 Telecom Phase / Time Profile (full timing support)
ITU-T G.8275.2 Telecom Phase / Time Profile (partial timing support)
SMPTE ST 2059-2 Broadcast Profile
IEEE 802.1AS TSN/AVB Profile
AES67 Media Profile
DOCSIS 3.1
PTP Modes: Multicast/Unicast Layer 2 (IEEE 802.3)
Multicast/Unicast Layer 3 (UDP IPv4/IPv6)
Hybrid Mode
E2E / P2P Delay Mechanism
Up to 128 messages/second per client
NTP Mode: NTP Server mode (8 ns time stamp accuracy)
NTPD Software Service (15,000 req./s)
1588 Clock Mode: 1-Step, 2-Step for both Master and Slave operation
Synchronous Ethernet: Master and Slave Capability
Compliant to ITU-T G.8261, G.8262 and G.8264
Ethernet Synchronization Messaging Channel (ESMC)
Network Protocols: IPv4, IPv6
DHCP, DHCPv6
DSCP
IEEE 802.1q VLAN filtering/tagging
IEEE 802.1p QOS
Ethernet Interface: Combo Port: 1 x 100/1000BASE-T RJ45, 1 x GBIT SFP - Slot
USB Interface: USB 1.1 / USB 2.0 full-speed, Micro USB female connector
Signal Outputs: 2x SMA, TTL (50 Ohm) connectors
configurable signals: 1PPS, 10MHz, 2048kHz
CPU: 825 MHz Cortex A9 Dual Core on SOC
Time Stamp Accuracy: 8 ns
HPS
SYNC
100
Out 2Out 1
6 Date: 14th November 2019 IMS-HPS-100 Setup Guide

4 HPS-100: PTP / SyncE / Hardware NTP Interface
LED Indicators
LED St: Init lights blue during initialisation,
off in normal operation mode
LED In: red Error - TSU does not work correctly,
PTP services stopped
yellow No link, but initialized
green link up
red stopped
LED A - LED B: Shows the current State of the TSU
yellow - yellow Listening
green - off Master Mode
off - green Slave Mode
yellow - off Passiv Mode
off - yellow uncalibrated
red - red stopped
Performance Level Options:
Option Unicast Delay NTP PTPv1 PTP
Clients Req./s Req./s Monitoring
————————————————————————————————————————————-
PL-A 8 1024 1600 NO NO
PL-B 256 32768 51200 NO NO
PL-C 512 65536 102400 YES NO
PL-D 1024 131072 204800 YES YES
PL-E 2048 262144 409600 YES YES
A detailed configuration guide you will find in the corresponding firmware manual of the system. See chapter
"The Web Interface -> Configuration: PTP V2".
IMS-HPS-100 Setup Guide Date: 14th November 2019 7

4.1 HPS100 - Global Configuration
Operating Mode
If supported, there is an option to run a NTP service in Server mode with hardware timestamp support. Select
between PTP and NTP mode at this step. It is not possible to run both modes at the same time on one TSU card.
Select Profile
User can choose among preselected sets of PTP parameters defined in profiles usually used in different indus-
tries. If the default setting “Custom“ is selected, the user can select any parameter combination available in the
global configuration section as long as the PTP standard allows it. Depending on the selected profile, there
might be profile specific parameters available which can be found in the “Profile Specific Parameters“ section
below the standard PTP parameters sections.
8 Date: 14th November 2019 IMS-HPS-100 Setup Guide

4 HPS-100: PTP / SyncE / Hardware NTP Interface
There are six different presets currently supported on PTP cards:
In Multicast and Unicast Mode: Default E2E IEEE 1588-2008
Default P2P IEEE 1588-2008
Power IEEE C37.238
Telecom ITU-T G.8275.1
In Unicast
Master / Slave Mode: Telecom ITU-T G.8265.1
In Unicast or Multicast
Master / Slave Mode: SMPTE ST 2059-2
More information about the settings of the HPS unit can be found in the current LANTIME firmware manual.
4.2 Option: Output Configuration
The HPS100 module is equipped with one Gigabit Ethernet SFP/RJ45 Combo Port for network synchronization
and two SMA ouput connectors. The following list shows the available output signals:
•Off (inactive - no signal selected)
•PPS (generated locally on the HPS100, inverted)
•10 MHz (generated locally on the TSU)
•2.048 MHz (taken from active internal clock module)
•10 MHz (taken from active internal clock module)
•PPS (taken from active internal clock module)
Per default no output signal is active on both outputs.
IMS-HPS-100 Setup Guide Date: 14th November 2019 9

4.3 Firmware Update via Web Interface
If you need to update the software of your HPS100 time stamp unit, you need a specific update file. You can
download the latest HPS100 firmware version from our website: https://www.meinbergglobal.com/english/sw/refclock-
updates.htm
The update file can be uploaded to the HPS100 by first choosing the file on your local computer with the
"Browse" button and then press "Start Update". Afterwards you are prompted to confirm the start of the update
process.
10 Date: 14th November 2019 IMS-HPS-100 Setup Guide