Meinberg IMS-REL1000 User manual

SETUP GUIDE
IMS-REL1000
Hot-Plug Module
15th April 2021
Meinberg Funkuhren GmbH & Co. KG

Table of Contents
1 Imprint 1
2 Introduction 2
3 Important Safety Hints 3
3.1 AdditionalSafetyHints ........................................... 4
3.2 PreventionofESDDamage......................................... 5
3.3 SupplyVoltage ................................................ 6
3.4 Cabling..................................................... 6
4 Front Connectors IMS-REL1000 7
4.1 IMS-REL1000-StatusLEDs........................................ 8
4.2 ErrorRelay .................................................. 9
5 Before you start 10
5.1 ScopeofDelivery............................................... 10
5.2 DisposalofPackagingMaterials...................................... 11
5.3 Pre-selection ................................................. 11
6 System Installation 12
6.1 Important Hints for hot-pluggable IMS Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.2 Installation of hot-pluggable IMS modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.3 ConnectingtheSystem ........................................... 14
7 Configuration of the IMS-REL1000 15
7.1 Events ..................................................... 15
7.2 Settingrelaysmanually........................................... 16
8 RoHS and WEEE 17
Date: 15th April 2021 IMS-REL1000

1 Imprint
1 Imprint
Meinberg Funkuhren GmbH & Co. KG
Lange Wand 9, 31812 Bad Pyrmont / Germany
Phone: + 49 (0) 52 81 / 93 09 - 0
Fax: + 49 (0) 52 81 / 93 09 - 230
Internet: https://www.meinbergglobal.com
Mail: [email protected]
Date: 15.04.2021
IMS-REL1000 Date: 15th April 2021 1

2 Introduction
This Setup Guide is a systematically structured guideline which supports you during the set-up of your Mein-
berg product.
The IMS-REL1000 is used as an error relay module that can be used to switch a variety of operating states
(e.g. Clock Not Sync, Antenna Faulty, etc.). If the internal hardware clock is running synchronously to the
reference source, the relay will switch to NO (Normaly Open) mode. In the event of an error, the relay will
switch to NC (Normaly Closed) mode.
Functionality.
Depending on the IMS system, is redundant with two reference clocks and IMS-RSC module (switching unit) or
with one reference clock and SPT module, different relay states can be switched. There is also the possibility
to set the relays A + C by different events.
The LANTIME firmware manual provides a complete description of all configurations and status monitoring
options of your Meinberg product.
Download LTOS7 Firmware manual:
http://www.mbg.link/doce-fw-ltos
Compatibility
The IMS-REL1000 is an IMS module that is compatible with the following systems of the IMS family. Further-
more the module can be used in the following slots.
M500
M1000
M1000 S
M2000 S
M3000
M3000 S
M4000
MRI
ESI
I/O
Compatibility - IMS REL1000
IMS-Systems
Compatible
Applicable
IMS-Slot
2 Date: 15th April 2021 IMS-REL1000

3 Important Safety Hints
3 Important Safety Hints
Please make sure that IMS modules that can be exchanged during operation are always handled with utmost
care.
Before any maintenance work on the system:
•Backup of stored configurations is recommended (e.g. via USB stick or Web UI)
•Please note the chapter "Prevention of ESD damage".
•Please note the chapter "Supply voltage".
IMS-REL1000 Date: 15th April 2021 3

3.1 Additional Safety Hints
This manual contains important information for the installation and operation of this device as well as for your
safety. Make sure to read carefully before installing and commissioning the device.
Certain operating conditions may require the observance of additional safety regulations not covered by this
manual. Nonobservance of this manual will lead to a significant abatement of the security provided by this
device. Security of the facility where this product is integrated lies in the responsibility of the installer.
The device must be used only for purpose named in this manual, any other use especially opteration above the
limits specified in this document is considered as improper use.
Keep all documents provided with the device for later reference.
This manual is exclusively for qualified electricians or by a qualified electrician trained personnel who are
familiar with the applicable national standards and specifications, in particular for the construction of high
voltage devices.
4 Date: 15th April 2021 IMS-REL1000

3 Important Safety Hints
3.2 Prevention of ESD Damage
ATTENTION!
The designation ESD (Electrostatic Sensitive Devices) refers to measures which are used
to protect electrostatically endangered components from electrostatic discharge and thus
to prevent destruction. Systems and assemblies with electrostatically endangered components
usually have the following characteristics:
Indicator for assemblies with electrostatic endangered components
The following measures protect electrostatically endangered components from destruction:
Prepare removal and installation of assemblies
Unload yourself (for example, by touching a grounded object) before touching assemblies.
Ensure that you wear a grounding strap on the wrist when working with such assemblies, which
you attach to an unpainted, non-conductive metal part of the system.
Use only tools and devices that are free from static electricity.
Transporting Assemblies
Assemblies may only be touched at the edge. Do not touch any pins or conductors on assemblies.
Installing and Removing Assemblies
Do not touch persons who are not grounded while removing or installing components. This could
result in a loss of grounding protection from your electrostatic discharge.
Storing Assemblies
Always keep assemblies in ESD protective covers. These protective covers must be undamaged.
ESD protective covers, which are extremely wrinkled or even have holes, no longer protect against
electrostatic discharge.
ESD protective covers must not be low-resistance and metallically conductive if a lithium battery
is installed on the assembly.
IMS-REL1000 Date: 15th April 2021 5

3.3 Supply Voltage
WARNING!
The IMS system in which the module is used operates at a dangerous voltage. The specific safety instruc-
tions can be found in the manual of the respective IMS System.
If the module is a hot-pluggable power supply unit, disconnect its power cable before removing it from the
IMS System.
Never open a power supply unit cause dangerous voltages can even exist after it has been disconnected from
the electrical supply. If a power supply is not working anymore, e.g. due to a defect, please send it back to
Meinberg for necessary repairs.
Non-observance of these safety instructions can cause serious personal injury and material damage. Installation,
initial start-up and operation of the IMS System may only be performed by qualified technical experts.
3.4 Cabling
WARNING!
Danger to life through electric shock! Never work with voltage applied! When working on the plugs and
terminals of connected cables, always disconnect both sides of the cables from the respective devices!
6 Date: 15th April 2021 IMS-REL1000

4 Front Connectors IMS-REL1000
4 Front Connectors IMS-REL1000
1
2
IMS-REL1000 Date: 15th April 2021 7