MELICONI Easytel 2+ User manual

Easytel 2+
Thank you for choosing a Meliconi remote control.
The Easytel 2+ remote control is designed to command a TV and a DECODER (satellite or digital terrestrial).
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the 5button and check that the LED remains on
continuously until the button is released. If the light is off or blinks, the inserted batteries are low,
therefore they need replacement.
WARNING:
As the remote control is capable of controlling 2 devices, during setup (and also during normal use), you must select the
operation mode; then define which device you want to control. (TV / STB)
To select the operation mode, press the button quickly and repeatedly until the LED corresponding to
the device you want to operate is switched on. (TV = red led / STB = green led)
Before using the remote control, for each device you wish to control, it is essential to set a specific code, it matched.
Identify the specific code and set it into the remote control using one of the following ways:
MANUAL
SEARCH
SMARTPHONE
TABLET - WEB
ACTIVATION OF REMOTE CONTROL
SELECTION OF OPERATING MODE
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, fire
or the like.
The product is not a toy. Keep out of reach of children or domestic animals.
Keep this booklet for future reference

Use the qr-code on the side or connect to the www.cme.it page and follow the instructions.
Once you have found the specific code for your device, set it in the remote control as described in the
ENTERING THE CODE DIRECTLY chapter.
ATTENTION: searching for the suitable code could last up to 5 minutes.
•Stand in front of the device to be controlled and make sure it is ON (not in stand-by). If necessary, switch
it on using the original remote control (if this is still working) or the buttons present on the device itself. (on
TVs they can be on the side or the top)
•On the MELICONI remote control select the operating mode and then press and hold the button
until the LED of the remote control lights up; release.
•Pointing the remote control towards the device, PRESS AND HOLD the ON/OFF button and wait
(even up to 5 minutes) for the device to switch off or that a shutdown menu appears.
•PAY ATTENTION, when the device turn off, IMMEDIATELY RELEASE the button.
•Three final flashes indicate that the operation has been completed successfully.
(only to be performed if you know the specific code to be set)
•On the MELICONI remote control select the operating mode and then press and hold the button
until the LED lights up; release.
•Immediately enter the previously identified specific code.
•Three final flashes indicate that the operation has been completed successfully.
If the remote control does NOT carry out the three final flashes, the setting is NOT successful; repeat the procedure.
If still unsuccessful, it means that the code is not included in the remote control, contact the ASSISTANCE.
ENTERING THE CODE DIRECTLY
VERIFY
Check that the MELICONI remote control operates your device in the main functions; if it does not, REPEAT the
procedure.
NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains off.
If no results are obtained, try using the procedure described in the SMARTPHONE - TABLET - WEB chapter or contact
the ASSISTANCE.
MANUAL SEARCH
SMARTPHONE - TABLET - WEB
watch
the video
watch
the video

The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, connect to the www.cme.it page, use the on-line tool ACTIVATION OF REMOTE CONTROL and continue
until you see the list matching buttons between the original remote control and the MELICONI remote control.
If the functions you want to play are matched with an number in orange color, operate as follows:
1. On MELICONI remote control select the operating mode and then press and hold the button until
the LED turn on; release the button.
2. Enter the code 0707.
3. While the LED remains on, enter the previously identified number corresponding to the function you
want to play.
4. While the LED flashes, within 30 seconds, on the MELICONI remote control press the desired button to
match the function obtained.
5. Repeat the procedure from point 3 for each function you want to add on MELICONI remote control.
6. To end the procedure, hold down the button and wait for three flashes of the LED indicating that
the storage has been completed; release the button (the used buttons loses their original function that
will be called by setting again the activation code).
For any future activation of the remote control, it is advisable to extract and note the code in use, operate as follows:
•On the MELICONI remote control select the operating mode and then press and hold the
button until the LED lights up; release.
•Enter the code 0010.
•After a pause of several seconds, the LED produces four sets of flashes, spaced out,
corresponding to the code to be obtained. Count the number of flashes. Each set of flashes
corresponds to one digit in the code. Ten flashes correspond to the digit zero “0”.
(example code obtained = 1701)
•Make a note of the code obtained. You may need it in future.
If you want to delete the function in combination with a single button, operate as follows:
1. On MELICONI remote control select the operating mode and then press and hold the button until the LED turn on;
release the button.
2. Enter the code 0707.
3. While the LED remains on, enter the code 1600.
4. While the LED flashes, within 30 seconds, on the MELICONI remote control press the button which you want to delete
the function
5. Repeat the procedure from point 3 for each function you want to delete on MELICONI remote control.
6. To end the procedure, hold down the button and wait for three flashes of the LED indicating that the storage has
been completed; release the button (to recall the original functions, setting again the activation code).
DELETE FUNCTION BY SINGLE BUTTON
DISPLAY CODE IN USE
BUTTONS AND FUNCTIONS
watch
the video

Using the MELICONI remote control to command 2 devices (TV and DECODER) it is often necessary to select the operating
mode before to operate on the corresponding device.
To avoid this uncomfortable and frequent operation, it is possible to combine in a single keyboard two different modes of use.
Automatically the V+ V- keys will control the TV, while the remaining keys will be the DECODER.
Operate as follows:
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0069.
•Three final flashes indicate that the operation has been completed successfully.
To obtain a function related to the other mode of use, for example the ON/OFF function of the DECODER, press and
hold the button and press the desired key ( + ).
To return to operate in the two distinct mode of use, carry out the procedure using the code 0096.
By activating the CHILD MODE, the remote control only enables the main functions:
NUMBERS V+ V- P+ P- EXIT
All other functions are blocked.
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0123.
•Three final flashes indicate that the operation has been completed successfully.
To restore all the original functions, insert code 0123 on the Meliconi remote control..
If necessary it is possible to completely reset the remote control and bring it back to the initial conditions.
WARNING : All user settings will be lost. Operate as follows:
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0279.
•Three final flashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
CHILD MODE
COMBINED KEYPAD
watch
the video

●IF THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK
It is possible that the code set in the remote control is incorrect for the device that you want to control. Check that you have
carried out all the settings procedures correctly. If necessary repeat them, following all the steps indicated carefully.
Consult the website www.cme.it to identify the specific code associated with your device or contact the ASSISTANCE.
●IF THE REMOTE CONTROL IS NO LONGER ABLE TO CONTROL THE DEVICE
Disconnect the device from the electric socket and leave it without power for a few minutes; switch the device on again.
Remove the batteries from the remote control, press the ON/OFF button twice and insert NEW batteries.
Make sure that the remote control is pointing at the device without any obstacles between them.
When pressed (even unintentionally) the button , you put the remote control to command a certain type of device.
Be sure to operate in the mode corresponding to the device to be controlled; select the correct operating mode and check if
the remote control resumes working.
If necessary try to the RESET OF THE REMOTE CONTROL and carry out a new activation.
●IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL
Usually the MELICONI remote control makes available only the present functions on his keyboard, provided they are
available also on the original remote control.
If some of the MAIN functions are not available, you are probably using an incorrect code. Find and set a more suitable code
as described in the ACTIVATION OF REMOTE CONTROL chapter.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, operate as described in the BUTTON AND FUNCTIONS chapter.
●HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals; use a camera (even that of the mobile phone).
Aim the infrared LED located in front of the remote control (not the red LED above) and press and hold on the remote control
the 5button.
If you see through the camera, the LED light with short white / light blue flashes means that the remote control works and
emits infrared.
web: www.cme.it e-mail: t[email protected]
IMPORTANT! To obtain technical assistance, it is essential to indicate the BRAND and MODEL of the appliance you intend
to control and the name of the MELICONI remote control you are using.
WARRANTY: 2 year Always keep your sales receipt as proof of the validity of the product’s warranty. The warranty is
voided if the product is tampered with or used improperly.
Meliconi SpA, Via Minghetti 10 - 40057 Cadriano di Granarolo Emilia, (BO) Italy
web: www.meliconi.com email: t[email protected]
ASSISTANCE
ATTENTION!
Most problems are caused by using insufficiently charged batteries.
We recommend checking and replace them as shown in the INSERTING THE BATTERIES chapter.
TROUBLESHOOTING (F.A.Q.)

The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the
end of its useful life the product must be collected separately from other waste. Therefore, at the end of the
device’s life, you must take it to appropriate centres for the differentiated collection of electrical and electronic
waste, or return it to the retailer when purchasing a new device of equivalent type. Suitable differentiated
collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible
treatment and disposal, help to prevent any negative effects on the environment and health and to promote
the recycling of the materials of which the device is made.
CAUTION: Batteries must not be disassembled, thrown into fire or released into the environment. Improper
use can cause damage to the environment and health. The symbol of the bins, indicating that the batteries
should be disposed of according to current regulations; inquire on collection of spent batteries and
accumulators in force in your country.