MELICONI SPEEDY 110 User manual

4
Thank you for choosing Meliconi.
This simplified universal remote control contains all the main functions of most
TV remote controls. Insert the batteries and program your remote control before using it.
Keep your Instructions Booklet for future reference.
USING THE KEYS AND FUNCTIONS
FITTING THE BATTERIES
GB
SET-UP
Read these instructions carefully before programming your remote control!
To use the remote control with your appliances, you must first program Speedy 110 as described below.
You can also visit our Internet site www.meliconi.com to have access to interactive instructions for easier
and faster remote control programming
• Batteries must be changed once a year.
• Change the batteries if the light indicator starts to flash during use. The batteries are low.
• When removing batteries, insert the new ones within 5 minutes or you may have to
reprogram your remote control.
• Make a note of the code for your TV on the adhesive label supplied inside the battery
compartment cover. This note will be handy if you have to reprogram your remote
control.
The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown:
ON/OFF to turn OFF your TV and, in
some cases, to turn ON your TV.
Control the volume using
+ .
To select an external terminal.
To select the next programme or to turn
ON your TV.
Mute key.
Press them together to turn ON your
TV on programme 1.
To select the previous programme
or to turn ON your TV.
Control the volume using - .
Light indicator.
Istr SPEEDY 110+ guscio V4.qxd 12-12-2007 17:09 Pagina 4

5
When you have programmed Speedy 110 Meliconi, note down the code on the label in the battery
compartment cover.
To find the code for your remote control:
1. Hold down the and keys simultaneously until the light indicator at the top starts to flash
indicating that the remote control is searching for the code.
2. Release the keys and, within 12 seconds, press and simultaneously.
3. Release and and pay attention to the flashing of the LED: a long flash corresponds to a +while
a short flash corresponds to a -. Note the sequence of the 9 flashes and note them down on the label
in the battery compartment cover, from left to right.
PROGRAMMING YOUR REMOTE CONTROL
1. Make sure that the TV is ON.
2.Hold down the and keys simultaneously until the light indicator at the top starts to flash indicating
that the remote control is in programming mode.
3. Press key four times then point the remote control at the appliance. Press and release the key
slowly several times. STOP when your TV goes OFF.
4.When your TV is OFF, press the and keys simultaneously. When you release the keys, three
flashes indicate that the search operation has been completed correctly.
Additional check
Check that all 7 keys are operating correctly. If the commands work incorrectly or erratically, you have
probably entered a code for a similar but different remote control.
In this case, repeat the search procedure from point 2 until all keys respond correctly to the commands sent.
IF YOU DO NOT HAVE THE PROGRAMME SELECTION KEYS ON YOUR ORIGINAL REMOTE CONTROL
If your remote control does not have the programme selection keys (e.g. / , +/-, CH+/-..etc) once you
have programmed Speedy 110, you can still select the programmes from 0 to 9, as follows:
•Hold down the and keys simultaneously until the light indicator starts to flash indicating that
the remote control is in programming mode.
•Release the keys and press 9 times within 12 seconds. Three flashes indicate that
the operation has been completed correctly.
•Make sure you can change programmes from 0 to 9 using the and keys. If not, repeat the search
operation, starting from point 2.
Identify and take note of the TV code which you have searched for, following the code noting
procedure (see "PROGRAMMED CODE NOTING" section).
NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY.
THE LIGHT INDICATOR STOPS FLASHING AND YOUR REMOTE CONTROL LEAVES
PROGRAMMING MODE IN THE FOLLOWING CASES:
•if no keys are pressed for 12 seconds
•if you press keys other than those indicated
•if the code search list is completed. In this case, visit www.meliconi.com or contact the call center.
PROGRAMMED CODE NOTING
P
-
+
P
P
-
+
P
P
-
P
-
+
P
P
-
+
P
+
P
Istr SPEEDY 110+ guscio V4.qxd 12-12-2007 17:09 Pagina 5

6
Once you have programmed Speedy 110, you can turn ON your TV in three ways:
•Press or .
•Press .
•Press and simultaneously: this sends the code for programme 1.
If the remote control is no longer programmed because it has been left without batteries for a long time
or has flat batteries, you can re-program it quickly as follows:
1. Hold down the and keys simultaneously until the light indicator at the top starts to flash
indicating that the remote control is programming.
2. Release the keys and, within 12 seconds, using the and keys, enter the nine-sign code which
you noted down before. At the end, three flashes indicate that the code has been saved correctly.
If not, try the code entry procedure again from point 1.
USING YOUR REMOTE CONTROL
To return to programme 1 directly, press and simultaneously.
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN
WARRANTY: 2 years
The warranty ceases to be valid if the product is tampered with or
used incorrectly.
Remote control model Speedy 110
Purchase date
PROBLEM
The TV does not respond and the light
indicator does not light up when you
press a key.
The TV or VCR does not respond but the
light indicator does light up.
The TV does not respond and the light
indicator flashes.
Not all remote control commands are
working correcting.
The and keys do not select the
programmes.
TROUBLESHOOTING
SOLUTION
Check that the batteries are fitted correctly. If necessary,
replace them with 2 new 1.5 V AAA/LR03 alkaline
batteries.
Check that the batteries are new and that the remote
control is pointing at the appliance without any obstacles
in the way. If required, reset the remote control code by
repeating the programming procedure.
Batteries are low. Replace them.
You may have used the wrong code. Reset the remote
control code, following the programming procedure.
The original remote control may not have had this
function. In this case, set the code (press 9 times) as
described in the PROGRAMMING YOUR REMOTE
CONTROL section above.
If you have any queries about Speedy 110:
•read this booklet carefully – this will help you to solve almost all problems
•consult our Internet site www.meliconi.com to answer all your queries easily and quickly.
INFO-LINE
Agent's stamp
P
-
+
P
P
-
+
P
P
-
+
P
+
PP
-
+
PP
-+
P
Istr SPEEDY 110+ guscio V4.qxd 12-12-2007 17:09 Pagina 6